Sanyo Plc Xp100l Projector User Manual

71

ON-SCREEN DISPLA yRESOLUTIONH-Freq .  (kHz) V-Freq  . (Hz)
VGA 1640x48031.470 59.880 
VGA 2720x40031.470 70.090 
VGA 3640x40031.470 70.090 
VGA 4640x48037.860 74.380 
VGA 5640x48037.860 72.810 
VGA 6640x48037.500 75.000 
VGA 7640x48043.269 85.000 
MAC LC13640x48034.970 66.600 
MAC 13640x48035.000 66.670 
480p640x48031.470 59.880 
575p768x57531.250 50.000 
575i768x576(Interlace)15.62550.000 
480i640x480(Interlace)15.73460.000
SVGA 1800x60035.156 56.250 
SVGA 2800x60037.880 60.320 
SVGA 3800x60046.875...

7

ON-SCREEN 
DISPLA yRESOLUTIONH-Freq .  (kHz) V-Freq  . (Hz)
D-VGA640x48031.470 59.940 
D-480p720x48031.470 59.880 
D-575p720x57531.250 50.000 
D-SVGA800x60037.879 60.320 
D-XGA1024x76843.363 60.000 
D-WXGA 11366x76848.360 60.000 
D-WXGA 21360x76847.700 60.000 
D-WXGA 31376x76848.360 60.000 
D-WXGA 41360x76856.160 72.000 
D-WXGA 51366x76846.500 50.000 
D-WXGA 61280x76847.776 59.870 
D-WXGA 71280x76860.289 74.893 
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq .  (kHz) V-Freq  . (Hz)
D-WXGA 91280x80049.600...

7

Technical Specifications
Mechanical Information  
 Projector Type   Multi-media Projector 
 
Dimensions (W x H x D)
 
14.56” x 7.36” x 17.32” (370 mm x 187 mm x 440 mm) (Not including raised portions)
 
 
Net Weight
 
25.8 lbs (11.7 kg)
 
 
Feet Adjustment
 
0˚ to 6.5˚
           
               
Panel Resolution 
 LCD Panel System   1.3” TFT Active Matrix type, 3 panels  
 
Panel Resolution
 
1,024 x 768 dots
 
 
Number of Pixels
 
2,359,296 (1,024 x 768 x 3 panels)...

74

Optional Parts
Lens Replacement
The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector 
for wide variety of uses.
For installation and replacement of the lens, always contact the sales dealer. The projector lens must be 
installed or replaced by well-trained sales or service engineers. Do not attempt to install and replace the lens by 
yourself as it may cause injury.
Do not hold the lens when carrying or lifting the projector. It may cause...

75

Configurations of Terminals
ANALOG/ MONITOR OUT (Mini D-sub 15 pin)
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5

4

6
7
8
+5V Power
Horiz. sync.
Ground (Vert. sync.)
DDC Data
Sense 0
Vert. sync.
DDC Clock
9
1
10
1
11
14
15
CONTROL PORT CONNECTOR (D-sub 9 pin)
-----
R X D
T X D
-----
SG
-----
RTS
CTS
Serial
1


4
5
6
7
8
DIGITAL DVI-D (DVI   4 PIN)
1917
21018
31119
41220
51321...

76

Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or 
lost the number and unable to operate the projector, contact the service station. 
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
*   S h o u l d   t h e   fo u r- d i g i t   n u m b e r   b e 
changed,  the  factory  set  number  will 
be invalid.
Put the label below (supplied) on in a prominent place of 
the projector’s body while it is locked with a PIN code.
While the...

77

Dimensions
3.94 (100)
14.57 (370.0)
5.75 (146)
17.32 (440)13.58 (345)
4.13 (105)5.20 (132)
4.33 (110)4.33 (110)7.36 (187)
6.5º MAX
Screw Holes for Ceiling MountScrew: M6Depth: 0.393 (10.0)
2.05 (52)
Unit: inch (mm)
Appendix 

78

Serial Control Interface
AppendixAppendix
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial 
port.
Connect a RS-232C serial cross cable to CONTROL 
PORT on the projector and serial port on the PC.
 (See p.20)
Launch a communication software provided with PC 
and setup the communication condition as follows:
1
2
3
Baud rate  : 9600 / 19200 bps
Parity check   : none
Stop bit
   : 1
Flow control
  : none
Data bit
   : 8
Type the command...

79

The command is sent from PC to the projector with 
the format below;
     'C' [Command] 'CR'
       
Command: two charactors (refer to the 
command table below.
-The projector decodes the command and returns the 
'ACK' with the format below;
     'ACK'  'CR'
-When the projector can not decode the command, it 
returns with format below.
     ‘?’  ‘CR’ 
Format
Appendix
Functional Execution Command
CommandFunction
C00Turn the projector ON
C01Turn the projector...

80
Status Read Command
Appendix
The command is sent from PC to the projector with 
the format below;
     'CR' [Command] 'CR'
       
Command: one character (refer to the command 
table below.
The projector decodes the command and returns the 
'Charactor string' with the format below;
Format
CommandFunctionProjector 
ReturnProjectro status
CR0Status Read
00Power On
80Stand-by mode
40Countdown
20Cooling down
10Power Malfunction
28Cooling down at the temperature anomaly
24Cooling...