Sanyo Plc Xp100l Projector User Manual

11

Rear Terminal
t	R/C  j ACK
  When using the wired remote control, connect the 
wired remote control to this jack with a remote 
control cable (not supplied).
y	USB CONNECTOR (Series B)
 
Use this connector when controlling a computer 
with the remote control of the projector. Connect 
the USB terminal of your computer to this 
connector with the supplied USB cable (p.20).
i	 S-VIDEO INPUT  j ACK
  Connect the S-VIDEO output signal from video 
equipment to this jack (p.21).
o	MONITOR OUT TERMINAL...

1

w	INPUT button
 
Select an input source (pp.31–33).
q	ON/STAND-B y  button
 
Turn the projector on or off (pp.23–24).
e	LENS button
 
Enter the focus, zoom, and lens shift adjustment 
mode (p.27).
r	Point ed7 8 buttons
 
–
 
Select an item or adjust the value in the On-
Screen Menu (p.25).
 
–
 
Pan the image in Digital zoom + mode (p.40).
!1	WARNING TEMP  .  indicator
 
Blink red when the internal temperature of the 
projector exceeds the operating range (pp.63, 69-
70 ).
t	MENU button
 
Open...

1

o
t
y
q STAND-B y  button
  Turn the projector off (p.24).
r  ON button
  Turn the projector on (p.23).
t INPUT 1 –    buttons
  Select an input source (INPUT 1 – INPUT 3) 
  (pp.31–33).
y	AUTO PC button
 
Automatically adjust the computer image to its 
optimum setting (pp.28, 35).
i	 P OINT ed 7 8 buttons
 
–
 
Select an item or adjust the value in the On-
Screen Menu (p.25).
 
–
 
Pan the image in Digital zoom + mode (p.40).
r
Remote Control
!0
u
!2
q
!2 L- C LICK button
 
Act as the left...

14

Remote Control
!6
!4
!5
!9
!7
!8
!3  MENU button
  Open or close the On-Screen Menu (p.25).
!6	ZOOM ed buttons
 
Zoom in and out the images (p.28).
!5	 D  . ZOOM button
 
Select the Digital zoom +/- mode and resize the 
image (p.40).
@0	FOCUS buttons
 
Adjust the focus (p.28).
!8	FILTER button
 
 Scroll the filter (p.29).
!4	P-TIMER button
 
Operate the P-timer function (p.29).
@1	NO SHOW button
 
Temporarily turn off the image on the screen (p.29).
@2	KE y STONE button
 
Correct keystone distortion...

15

Remote Control Battery Installation
123
Open the battery 
compartment lid.
Install new batteries into 
the compartment.
Replace the 
compartment lid.
Press the lid downward and slide it.Two AAA size batteriesFor correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.
To insure safe operation, please observe the following precautions :
 ●   Use two (2) AAA or LR03 type alkaline batteries.
 
●   Always replace batteries in sets.
 
●   Do not use a new battery...

16

The eight different remote control codes (Code 1–Code 8) are assigned to this pro\
jector. Switching the remote 
control codes prevents interference from other remote controls when several projectors or video equipment 
next to each other are operated at the same time. Change the remote control code for the projector first before 
changing that for the remote control. See “Remote control” in the Setting Menu on page 51.
Press and hold the MENU and a number button (1–8) 
for more than five seconds to...

17

ADJUSTABLE FEET
Projection angle can be adjusted up to 6.5 degrees with the 
adjustable feet. 
Rotate the adjustable feet and tilt the projector to the proper 
height; to raise the projector, rotate the both feet clockwise.
To lower the projector or to retract the adjustable feet, rotate the 
both feet counterclockwise.
To correct keystone distortion, press the KEYSTONE button on the 
remote control or select Keystone from the menu (see pages 14, 
29, 40, 44).
Adjustable Feet
Installation 

18

When replacing the lens or using an optional lens, install the lens by following the instructions below. Ask the 
sales dealer for detailed information of the optional lens specifications. 
Lens Installation
While pressing the top cover release button on 
the top cover, slide the top cover toward front to 
remove it
Shift the lens to the center position by using the 
Lens shift function (p. 27).1
2
Removing the lensTop cover release button
CAUTION
Be careful when handling the lens. Do not 
drop....

19

NOTES ON LENS INSTALLATION
 
●
 
Do not touch or remove any parts except the lens and related parts. It may result in     
 
malfunctions, electrical shock, fire hazard or other accidents.
 
●
 
Before installing or replacing the lens, check that the Model No. of the Projection Lens   
 
matches to the projector.
 
●
 
For details of the lens and installation, contact the sales dealer where you purchased the  
 
 projector.
Fit the lens to the projector. Make sure that the 
lens is fully inserted to...

0

Monitor Output
BNCcable
Connecting to a Computer (Digital and Analog RGB)
Monitor Output
G   B   R   H/V   V
DVI-Digital cableVGA cableVGA cableUSB cable
USB port
Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables.
Cables used for connection  (✽ = Cables not supplied with this projector.)
• VGA Cable (One cable is supplied.) 
• DVI-Digital Cable ✽ 
• BNC Cable ✽ 
• Serial Cross Cable✽
• USB Cable
Monitor Output
DIGITAL INANALOG...