Sanyo Plc Xe40 Projector User Manual

11
Part Names and Functions
Part Names & Functions
q
e
w
w Button 1-3
Used for Antitheft alarm setting.
e ALARM indicator
Blinks red to indicate the battery condition or key operation.
q F button
Used for Antitheft alarm setting.
Antitheft Alarm Setting Buttons
These buttons are used for Antitheft alarm function.  (pp. 50-52) 

12
Part Names and Functions
To ensure safe operation, please observe the following
precautions :
–  Do not bend, drop the remote control or expose the
remote control to moisture or heat.
–  For cleaning, use soft dry cloth.  Do not apply benzene,
thinner, splay or any chemical material.
t
e
!0
i
!4
r
!5
!3
qPOWER ON-OFF button 
Turn the projector on or off.  (pp. 19, 20)
wVIDEO button
Select VIDEO input source.  (pp. 24, 35)
eCOMPUTER button
Select COMPUTER input source.  (pp. 24, 26, 36)
rMENU button...

13
Part Names and Functions
123
To insure safe operation, please observe the following precautions:
●Use (2) AA or LR6 type alkaline batteries.
●Always replace batteries in sets.
●Do not use a new battery with a used battery.
●Avoid contact with water or liquid.
●Do not expose the remote control to moisture or heat.
●Do not drop the remote control.
●If the battery has leaked on the remote control, carefully wipe the case clean and install new 
batteries.
● Risk of explosion if a battery is replaced by an...

14
✔Note:
• This projector is not equipped with optical zoom.  To adjust the screen size, change the throw distance.
• The brightness in the room has a great influence on picture quality.  
It is recommended to limit the ambient lighting in order to get the best image.
• The values below are approximate and may vary from the actual sizes. 
64”70”78”80”
60”
 A
B
3.38 (1.03m)
3.28 (1.00m)
2.92 (0.89m)
2.66 (0.81m) A : B  =  10 : 1.2
Screen Size
(W x H) mm
4 : 3 aspect ratio
Throw distance
60”
1219 x 914...

15
NOTE ON THE POWER CORD
AC power cord must meet requirement of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If supplied AC power cord does not match your AC outlet, contact your sales dealer.
To power cord 
connector on your 
projector.
Projector sideAC outlet side
Ground
To the AC outlet.
(120 V AC)
For Continental EuropeFor the U.S.A. and Canada
This projector uses nominal input voltages of 100-120 V or
200-240 V AC....

16
Installation
Connecting to a Computer
ON ON
S-VIDEO IN  
MONITOR  OUTCOMPUTER IN 2 / 
COMPUTER / COMPONENTAUDIO  IN
R
VIDEO INL(MONO)
(VARIABLE)
AUDIO  OUTCOMPUTER  IN  1/ COMPONENT INUSBSERVICE PORT RESET
Cables used for connection 
• VGA Cables (Mini D-sub 15 pin) (Only one cable is supplied.) 
•USB Cable 
• Audio Cables (Mini Plug: stereo) 
(Not all the cables are suppled with this projector.)
External Audio Equipment
VGA cable   USB cable 
Audio cable
(stereo) 
Audio cable 
(stereo) Monitor...

17
S-VIDEO IN  
MONITOR  OUTCOMPUTER IN 2 / 
COMPUTER / COMPONENTAUDIO  IN
R
VIDEO INL(MONO)
(VARIABLE)
AUDIO  OUTCOMPUTER  IN  1/ COMPONENT INUSBSERVICE PORT RESET
Installation
Connecting to Video Equipment
Cables used for connection  
• Video and Audio Cable (RCA x 3) 
• S-VIDEO Cable 
• Audio Cable (Mini Plug: stereo) 
(Not all the cables are suppled with this projector.)
✔Note:
• When connecting AUDIO OUT to external audio equipment, the
projectors built-in speaker is disconnected.
• See p. 65 for...

18
Installation
Connecting to Component Video Equipment
S-VIDEO IN  
MONITOR  OUTCOMPUTER IN 2 / 
COMPUTER / COMPONENTAUDIO  IN
R
VIDEO INL(MONO)
(VARIABLE)
AUDIO  OUTCOMPUTER  IN  1/ COMPONENT INUSBSERVICE PORT RESET
Cables used for connection
• Audio Cables (Mini Plug :stereo) 
• Scart-VGA Cable  
• Component Cable 
• Component-VGA Cable  
(Not all the cables are suppled with this projector.)
✔Note:
• When connecting AUDIO OUT to external audio equipment, the
projectors built-in speaker is...

19
Connect the projectors AC power cord into an AC
outlet.  The POWER indicator becomes red.
Press the POWER ON-OFF button on the remote
control.  The POWER indicator becomes green and the
cooling fans start to operate.  The preparation display
appears on the screen and the count down starts. 
2
3
1
16
The preparation display disappears after 30
seconds.
4After the countdown, the input source that was
selected last and the Lamp mode status icon (see p.
46) appear on the screen.
If the projector is locked...

20
Basic Operation
Press the POWER ON-OFF button on the remote
control, and Power off? appears on the screen.  
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator starts to blink red, and
the cooling fans keep operating.  (You can select the
level of fan quietness and rotation speed. See p. 49.)
At this time you can disconnect the AC power cord
even if the fans are still running.
1
2
TO MAINTAIN THE LIFE OF THE LAMP, ONCE
YOU TURN THE PROJECTOR ON, WAIT AT
LEAST 5 MINUTES...