Sanyo Plc Xe40 Projector User Manual

Multimedia Projector 
MODELPLC-XE40
Owner’s Manual 

2
Features and Design
◆Large Screen in Limited Space
- Short focus lens allows you to project large images
from short distance.  (p. 14)
◆Antitheft Alarm Function
This projector is equipped with an Antitheft alarm
function which sounds when a vibration is detected.
(pp. 48, 50 - 52)
◆Security Features
- The projector cannot be operated without remote
control.  Keep the remote control securely at hand
to minimize the risk of theft. 
- Easily identifiable orange cabinet for security. 
- The PIN cord lock...

3
Table of Contents
Trademarks
Each name of corporations or products in this book is either a registered trademark or a trademark of its respective
corporation.
Features and Design  . . . . . . . . . . . . . . . . . . .2
Table of Contents  . . . . . . . . . . . . . . . . . . . . . .3
To the Owner  . . . . . . . . . . . . . . . . . . . . . . . . .4
Safety Instructions  . . . . . . . . . . . . . . . . . . . .5
Air Circulation 6
Installing the Projector in Proper Position 6
Moving the Projector 6
Compliance...

4
To the Owner
CAUTION : T O  REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK).  NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNERS MANUAL WITH
THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before operating this...

5
Safety Instructions
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for later
use.  Unplug this projector from AC power supply before
cleaning.  Do not use liquid or aerosol cleaners.  Use a damp
cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time,...

6
Safety Instructions
USE CAUTION IN CARRYING OR 
TRANSPORTING THE PROJECTOR
–Do not drop or bump the projector, otherwise
damages or malfunctions may result.
–When carrying the projector, use a suitable carrying
case.
–Do not transport the projector by using a courier or
transport service in an unsuitable transport case.  This
may cause damage to the projector.  To transport the
projector through a courier or transport service, consult
your dealer for their information.
–
Do not put the projector in a...

7
AC Power Cord for the United Kingdom :
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.  Should the
fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus  .  If the fuse cover is
detachable, never use the plug with the cover omitted.  If a replacement fuse cover is required, ensure it is of the same colour as that visible
on the pin face of the plug (i.e. red or orange)....

8
Bottom Back
qAntitheft alarm setting buttons
wFocus Lever
eProjection Lens
rLens Cover
(See p. 54 for attaching)
tu
!6
!2!4
!0!1CAUTION
Hot air is exhausted from the exhaust
vent.  Do not put heat-sensitive objects
near this side.
eyrt
Front
Part Names and Functions
o
i
!5
CAUTION
Do not turn on the projector with putting
the lens cover on.  The light beam may
damage lens cover and result in fire
hazard.
Attach the lens cover while the projector
is not in use to avoid scratching the lens
surface....

9
Part Names and Functions
RESET button
A built-in micro processor which controls this unit may
occasionally malfunction and need to be reset.  Press the
RESET button with a pen, then the projector shuts down and
restarts.  Do not use the RESET function excessively.
Rear Terminal
S-VIDEO IN  
MONITOR  OUTCOMPUTER IN 2 / 
COMPUTER / COMPONENT
AUDIO  IN
R
VIDEO INL(MONO)
(VARIABLE)
AUDIO  OUT
COMPUTER  IN  1/ COMPONENT INUSBSERVICE PORT RESET
qwerty
i
u
t S-VIDEO IN
Connect the S-VIDEO output from video...

10
Part Names and Functions
REPLACEPOWER WARNINGLAMP 
qwe
e LAMP REPLACE indicator
Turn yellow when the life of the projection lamp draws to an
end.  (pp. 56, 62)
w WARNING indicator
Emit a red light when the projector detects abnormal condition.
This also blinks red when the internal temperature of the
projector exceeds the operating range.  (pp. 53, 62)
q POWER indicator
It turns red when the projector is in the stand-by mode.  
It remains green while the projector is under operation.  
(pp. 19, 20,...