Sanyo Pdg Det100l Projector User Manual

81
Appendix
ON-SCREEN DISPLA yRESOLUTION
H-Freq .(kHz)V-Freq .(Hz)
1080p 1920x1080
33.75030.000
1920x1080 28.12525.000
1920x1080 27.00024.000
1920x1080 67.50060.000
1920x1080 56.25050.000
1080psf/30 1920x1080 33.75060.000
1080psf/25 1920x1080 28.12550.000
1080psf/24 1920x1080 27.00048.000
When an input signal is digital from the DVI terminal, refer to the chart below.
✔Note:
•Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.
•Specifications...

82
Appendix
On-BoardOptional Interface Board
Input1Input2DsubDsub
-DVI Component
-S-video Component HDCP
-DVI SDI
Analog 
PC
Scart
Digital
Analog 
PC
Component Video/
S-Video Analog 
PC
Analog 
PC
Scart
Digital
Analog 
PC
Component Video/
S-video Analog 
PC
Component Analog 
PC
Scart
Digital Digital
On-Board
Input1 Analog PC
o    
o    o    o    o    o    o    o    o    o    o    o    o    o    o    o     o    
Scarto    o    o     -        -        -        -        o     -        -        -        -...

83
Technical Specifications
Mechanical Information 
 Projector Type  Multi-media Projector 
  Dimensions (W x H x D)  15.75” x 9.55” x 20.61” (400.0 mm x 242.5 mm x 523.5 mm) 
  Net Weight  43.65lbs (19.8 kg) 
  Feet Adjustment  0˚ to 5˚           
          
DLP Chip 
 Projection System  0.95” Single DLP chip, High brightness color wheel x 2   
  Number of Pixels  1,470,000 pixels (1,400 x 1,050 dots)           
         
Signal Compatibility 
 Color System PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N...

84
Optional Parts
     Model No.
Wired Remote Cable(30m)     : POA-CA-RC30 
Optional Interface Board (DVI)     : POA-MD18DVI
Optional Interface Board (5-BNC)     : POA-MD16VD1
Optional Interface Board (D-sub 15)  : POA-MD04VGA
Optional Interface Board (Dual-SDI)  : POA-MD17SDID
Optional Interface Board (DVI / D-sub 15)  : POA-MD23ADI
Optional Interface Board (5-BNC / VIDEO)  : POA-MD25VD3
Optional Interface Board (WARP & BLENDING)  : POA-MD21WARP
The parts listed below are optionally available. When...

85
Configurations of Terminals
ANALOG (Mini D-sub 15 pin)
512341096781514131 112
Red Input
Ground (Horiz.sync.)
Green Input
No Connect
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V Power
Horiz. sync.
Ground (Vert. sync.)
DDC Data
Ground
Vert. sync.
DDC Clock
9
13
10
12
11
14
15
CONTROL PORT CONNECTOR (D-sub 9 pin)
-----
R X D
T X D
-----
SG
-----
RTS
CTS
Serial
1
2
3
4
5
6
7
8
DIGITAL DVI-D (DVI 24 PIN)
1917
21018
31 119
41220
51321
61422
71523
81624
T.M.D.S. Data2–
No Connect...

86
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or 
lost the number and unable to operate the projector, contact the service station. 
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
*  S h o u l d   t h e   fo u r- d i g i t   n u m b e r   b e 
changed,  the  factory  set  number  will 
be invalid.
Put the label below (supplied) on in a prominent place of 
the projector’s body while it is locked with a PIN code. While the...

87
Dimensions
Unit: inch (mm)
Appendix
0.28(7.0)
9.21(234.0)9.55(242.5)
4.45(113.0)
20.47(520.0)
20.61(523.5)
15.75(400.0)
8.31(211.0)
5.0º
5.0º
19.96(507.1)
96.0º
6.02(153.0) 5.63(143.0)
6.81(173.0) 6.81(173.0)
5.08(129.0)4.65(118.0)
2.64(67.0)
4.25(108.0)
12.48(317.0)
5.79(147.0)4.92(125.0)
6.50(165.0)6.50(165.0)
14.29(363.0)
Screw Holes f or Ceiling Mount
Scre w: M8
Depth:  0.393 (10.0) 

88
Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial 
port.Connect a RS-232C serial cross cable to SERIAL 
PORT IN on the projector and serial port on the PC.
 (See p.11)
Launch a communication software provided with PC 
and setup the communication condition as follows:
1
2
3Baud rate  : 9600 / 19200 bps
Parity check  : none
Stop bit   : 1
Flow control  : none
Data bit   : 8
Type the command for controlling the...

89
Status Read Command
Appendix
The command is sent from PC to the projector with 
the format below;
     'CR' [Command] 'CR'
        Command: one character (refer to the command 
table below.
The projector decodes the command and returns the 
'Character string' with the format below; Format
Command
FunctionProjector 
Return Projector status
CR0
Status Read 00
Power On
80 Stand-by mode
40 Countdown
20 Cooling down
10 Power Malfunction
28 Cooling down at the temperature anomaly
02...

90
AppendixHow to adjust multiple screens
With the Edge blending and Color matching functions, you can seamlessly display the images from more than two 
projectors. Follow the steps below to adjust multiple projector images. 
Confirm if you use the same type of color wheel (high brightness or rich color reproduction color wheel) for each 
projector, and set the same screen size and image level.1
4Adjust the position, focus and zoom of each image if necessary, and then overlap the shaded areas by using...