Sanyo Pdg Det100l Projector User Manual

71
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described \
on pages 20–21.
2.  Check the cable connection. Make sure that all computers, video equipment, and power cords are properly 
connected.
3.  Make sure that all power is switched on.
4.  If the projector still does not produce an image, restart your computer.
5.  If an image still does not appear,...

72
	
appears on the screen
–  The end of lamp life is approaching. Replace the lamp with a new one promptly.
   (See page 66)
appears on the screen
–   The filter is out of scroll. Replace the filter cartridge with a new one promptly.
   (See pages 62-63)
The image is out of focus.
– Adjust the focus of the projector.
– Check Projection Lens to see if it needs cleaning.
 ✔Note:   Moving  the  projector  from  a  cool  temperature  location  to  a  warm  temperature 
location  may  result  in  moisture...

73
wARNING: 
High voltages are used to operate this projector  . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, contact the dealer where you purchased the projector 
or  the  service  center.  Specify  the  model  number  and  explain  about  the  problem. We  will  advise  you  how  to  obtain 
service.
This  symbol  on  the  nameplate  means  the  product  is  Listed  by  Under writers 
Laboratories  Inc.  It  is  designed  and  manufactured...

74
Menu Tree
InputRGB (PC analog)Go to System (1)Input 1
Y, Pb/Cb,Pr/Cr
Computer Input/Video Input
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
Input 3
RGB Go to System (1)
Go to System (3)
Go to System (2)Video
S-video
Input 2
Go to System (1)
Input
H-sync freq.
V-sync freq.
Projector
Information
Key lock
ScreenLanguageLamp mode
Power managementSecurity
Color wheel type
Quit0–63
0–63
Off/On/Film
Image AdjustContrastBrightnessColor ✽Tint ✽
RedGreenBlue
Sharpness
ResetStore
Gamma
Progressive ✽
0–63
0–63...

75
Computer Input
System (1)Mode 1
Mode 2Image SelectStandard
Real
DICOM
ScreenNormal
True
Wide
Digital zoom +
Digital zoom -PC AdjustAuto PC adj.
Fine sync.
Total dots
Position H
Position V
Clamp
Display area - H
Display area -  V
Reset
Mode free
Store
Quit
0–31
Yes/No
Mode 1
Mode 10
Quit
✽ System displayed in the System Menu varies depending on the input signal.
✔Note:
•The Menu display varies depending on the input signal.
SVGA 1
SVGA 2
SVGA 3
Rear
Keystone
Ceiling Reset
StoreOn/Off
On/Off
CustomH &...

76
Computer Input/Video Input
Appendix
SettingFan control
All/Front & Top/Top & Back/Front & Back/
Front/Top/Back Normal/Max
Power managementRC sensor
Off/Ready/Shut down
1–30 Min.
Quit
On/Off
On start
Key lock
SecurityOff
Projector
Remote Control
PIN code lock Off/On1/On2
PIN code change
Used timeFilter counter
Yes/NoFactory default
Code 1Remote Control
Code 8
Quit
Yes/No
Quit
8 test patterns providedTest pattern
Quit
Quit
Projector ID
ShutterProtection
Management
Remote controlOn / Off
ProjectorOn /...

77
Indicators and Projector Condition
Check the indicators for the projector condition.
The projector is operating normally .
• • • on
• • • off• • •  
blinking at the normal rate       
(approx. 1 second ON,         
1 second OFF)
• • • dim
• • •  blinking slow           
(approx. 2 seconds ON, 
2 seconds OFF)
• • • blinking fast              
(approx. 0.5 seconds ON,  
0.5 seconds OFF)
Appendix
Indicators
Projector ConditionPOWER
green LAMP
red WARNING
TEMP.
red WARNING
FILTER
orange SHUTTER
blue LAMP...

78
Appendix
The projector is detecting abnormal condition .
Indicators
Projector ConditionPOWERgreen LAMP
red WARNING
TEMP.
red WARNING
FILTER
orange SHUTTER
blue LAMP 1/2
REP.
orange
The temperature inside the projector is elevated 
close to the abnormally high level.
The temperature inside the projector is abnormally 
high. The projector cannot be turned on. When 
the projector is cooled down enough and the 
temperature returns to normal, the POWER 
indicator lights green and the projector can be...

79
Appendix
The projector is detecting abnormal condition .
Indicators
Projector ConditionPOWERgreen LAMP
red WARNING
TEMP.
red WARNING
FILTER
orange SHUTTER
blue LAMP 1/2
REP.
orange
If the Filter counter reached a time set in the timer 
setting, a Filter replacement icon (Fig.2) appears 
on the screen and the WARNING FILTER indicator 
on the top panel lights up. Replace the filter as 
soon as possible. If the filter is out of scroll and the 
projector reaches a time set in the timer setting, Fig. 
3...

80
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below 
and less than 230 MHz of Dot Clock.
Appendix
✽“True”  cannot  be  selected  when WUXGA1, WXGA+2,  UXGA1,  UXGA2,  UXGA3,  UXGA4  and  UXGA5  are 
selected. (p.40)
ON-SCREEN DISPLA yRESOLUTION
H-Freq .(kHz)V-Freq .(Hz)
VGA 1 640x480 31.470 59.880 
VGA 2 720x400 31.470 70.090 
VGA 3 640x400 31.470 70.090 
VGA 4 640x480 37.860 74.380 
VGA 5 640x480 37.860...