Samsung LCD TV 530 User Manual

							English - 
Using the Energy Saving Feature
This feature adjusts the brightness of the TV in order to reduce power consumption. When watching TV at night, set the 
"Energy Saving “ mode option to “High” to reduce eye fatigue as\
 well as power consumption.
1.
   Press the MENU button to display the menu.  
Press the ▲ or ▼ button to select “Setup”, then press the  ENTER  button.
2.   Press the ▲ or ▼ button to select “Energy Saving”, then press the  
ENTER  button. Select the required option (Off, Low, Medium, High, Auto) 
by pressing the ▲ or ▼ button.
  Press the ENTER  button.
Off: Turns off the energy saving function. 
Low: Sets the TV to low energy saving mode.
Medium: Sets the TV to medium energy saving mode.
High: Sets the TV to high energy saving mode.
Auto: Automatically adjusts the brightness of the TV screen in 
accordance with the scenes.•
•
•
•
•
  Press the EXIT button to exit.
Setup
External SettingsEntertainment  : Off 
Energy Saving : Off	 ►
PIP
SW Upgrade
Setup
External SettingsEntertainment  : Off 
Energy Saving : Off	 ►
PIP
SW Upgrade
Off
Low
Medium
High 
Auto
BN68-01392D-01Eng-0221.indd   592008-02-22   ¿ÀÈÄ 5:44:48 
						

							English - 60
Upgrading the Software
Samsung may offer upgrades for TV's firmware in the future. Please contact the Samsung call center at 1-800-SAMSUNG 
(726-7864) to receive information about downloading upgrades and using\
 a USB drive. Upgrades will be possible by 
connecting a USB drive to the USB port located on your TV. 
1.
   Insert a USB drive containing the firmware upgrade into the SERVICE port on the rear of the TV.
2.
    Press the MENU button to display the menu.  
Press the ▲ or ▼ button to select “Setup”, then press the  ENTER  button.
3.   Press the ▲ or ▼ button to select “SW Upgrade”, then press the ENTER  button.
4.
    Press the ENTER  button. 
The message “Scanning for USB... It may take up to 30 seconds.” is\
 
displayed.
5.
   The message “Upgrade version XXXX to version XXXX? The system will be 
reset after upgrade.” is displayed.   
Press the ◄ or ► to select the “OK”, then press the  ENTER 
 button.
   Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically 
after completing the firmware upgrade. Please check the firmware version 
after the upgrades are complete. When software is upgraded, video and 
audio settings you have made will return to their default (factory) se\
ttings. We 
recommend you write down your settings so that you can easily reset them\
 
after the upgrade.
Setup
Energy Saving  : OffPIP
SW	Upgrade	 	 ►
Software Upgrade
Scanning for USB.....
It may take up to 30 seconds.
Software Upgrade
Upgrade version XXXX to version XXXX? The system will   
be reset after upgrade.
OKCancel
TV Rear Panel
USB Drive
BN68-01392D-01Eng-0221.indd   602008-02-22   ¿ÀÈÄ 5:44:48 
						

							English - 61
What is Anynet+
?
Anynet +
 is a function that enables you to control all connected Samsung devices\
 that support Anynet +
 with your Samsung 
TV’s remote.
About Anynet +
Connecting Anynet +
 Devices
The Anynet +
 system can be used only with Samsung devices that have the Anynet +
 feature. To be sure your Samsung 
device has this feature, check if there is an Anynet +
 logo on it.
To connect to a TV
TVAnynet +
 Device 1 Anynet +
 Device 2 Anynet +
 Device 
HDMI 1. Cable HDMI 1. Cable
HDMI 1. CableConnect the [HDMI 1], 
[HDMI 2] or [HDMI 3] 
jack on the TV and the 
HDMI OUT jack of the 
corresponding Anynet +
 
device using an HDMI 
cable.
To connect to Home Theater
TV Anynet+
 Device 1 Anynet +
 Device 2
Anynet+ Device 
HDMI 1. Cable
HDMI 1. Cable
HDMI 1. Cable
Optical Cable Home Theater
HDMI 1. Cable1.    Connect the 
[HDMI 1], [HDMI 
2] or [HDMI 3] 
jack on the TV 
and the HDMI 
OUT jack of the 
corresponding 
Anynet +
 device 
using an HDMI 
cable.
2.    Connect the 
HDMI IN jack of 
the home theater 
and the HDMI 
OUT jack of the 
corresponding 
Anynet +
 device 
using an HDMI 
cable.
Connect the Optical cable between the Digital Audio Out (Optical) jack on your TV and the Digital Audio Input on the 
Home Theater.
When following the connection above, the Optical jack only outputs 2 cha\
nnel audio. You will only hear sound from the 
Home Theater’s Front Left and Right speakers and the subwoofer. If you want to hear 5.1 channel audio, connect the 
DIGITAL AUDIO OUT (OPTICAL) jack on the DVD player or Cable/Satellite Box (ie Anynet Device 1 or 2) directly to 
the Amplifi er or Home Theater, not the TV.
Connect only one Home Theater.
You can connect an Anynet +
 device using the HDMI 1.3 cable. Some HDMI cables may not support Anynet +
 functions.
Anynet +
 works when the AV device supporting Anynet +
 is in the Standby or On status.
Anynet +
 supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
➣
➣
➣
➣
➣
➣
BN68-01392D-01Eng-0221.indd   612008-02-22   ¿ÀÈÄ 5:44:49 
						

							English - 62
Setting Up Anynet+
 
The following settings help set the Anynet +
 functions.
To use the Anynet+ Function, Anynet +
 (HDMI-CEC) must be set to On
1.
   Press the MENU button. Press the ▲ or ▼ button to select “Application”, 
then press the ENTER  button.
2.   Press the ▲ or ▼ button to select “Anynet +
 (HDMI-CEC)”, then press the 
ENTER  button.
3. Press the ENTER  button to select “Anynet+  (HDMI-CEC)”.
4.
  Press the ▲ or ▼ button to select “On”, then press the ENTER  button.
The “Anynet +
 (HDMI-CEC)” function is enabled.
If you select Off, “Anynet +
 (HDMI-CEC)” is disabled.
When the “Anynet +
 (HDMI-CEC)” function is disabled, all the Anynet +
 
related operations are deactivated.
Setting an Anynet +
 Device to turn Off Automatically when the TV is Turned Off
1.
    Press the ▲ or ▼ button to select “Auto Turn Off”, then press the ENTER  button.
2.
  Press the ▲ or ▼ button to select “On”, then press the ENTER  button.
The “Auto Turn Off” function is enabled.
If you select “Off”, the “Auto Turn Off” function is canceled.
  Press the EXIT button to exit.
The active source on the TV remote must be set to TV to use the Anynet +
 
function.
If you set “Auto Turn Off” to “On”, connected external devices are also turned 
off when the TV is turned off. If an external device is still recording, it may or 
may not turn off. 
➣
➣
➣
➣
➣
➣
➣
Scanning and Switching between Anynet +
 Devices
1.    Press the TOOLS  button.  
Press the ▲ or ▼ button to select “Device List”, then press the ENTER  button.
Anynet+ devices connected to the TV are listed.
If you cannot find a device you want, press the red button to scan for devices .
2.
    Press the ▲ or ▼ button to select to a particular device and press the ENTER  button. It is switched to the selected device.
Only when you set “Anynet +
 (HDMI-CEC)” to On in the “Application” menu, the 
“Device List” menu appears.
Switching to the selected devices may take up to 2 minutes. You cannot cancel the operation during the switching 
operation.
The time required to scan for devices is determined by the number of con\
nected devices. 
When the device scan is complete, the number of devices found are not di\
splayed.
Although the TV automatically scans devices when it is turned on using the  POWER button, devices connected when 
the TV is already on are not displayed in the device list. In this case, sel\
ect the Searching Connections menu to search 
devices.
If you have selected external input mode by pressing the  SOURCE button, you cannot use the Anynet+ function. Make 
sure to switch to an Anynet+ device by using the  TOOLS button.
➣
➣
➣
➣
➣
➣
➣
➣
Anynet+ (HDMI-CEC)
Anynet+ (HDMI-CEC)  : ON Auto Turn Off :Off
On
ReturnEnterMove
Application 
Anynet+	(HDMI-CEC)	 ►	 
Anynet+ (HDMI-CEC) 
Anynet+ (HDMI-CEC) : On Auto Turn Off :Off
On
ReturnEnterMove
TOOLS
  Device List  Record  Timer Recording  Receiver : OffPicture Mode  : StandardSound Mode  : CustomSleep Timer  : OffChannel Add/Delete▼
e  ExitEnter
Move
BN68-01392D-01Eng-0221.indd   622008-02-22   ¿ÀÈÄ 5:44:50 
						

							English - 6
Anynet+
 Menu
The Anynet +
 menu changes depending on the type and status of the Anynet +
 devices connected to the TV.
Anynet +
 Menu Description
View TV Switches from Anynet+
 to TV broadcast mode.
Device List Displays the Anynet+
 device list.
Record Starts a recording. (This menu works only for a device supporting recor\
ding.) 
Menu on Device Shows the menu of the connected device.   
Example: When a DVD Recorder is connected, the DVD Recorder’s title menu 
appears.
Device Operation Shows the play control menu of the connected device.   
Example: When a DVD Recorder is connected, the play control menu of the \
DVD 
Recorder appears.
Timer Recording Allows reserving a recording. (This menu works only for a device suppor\
ting 
recording reservations.)
Stop Recording Stops recording.
Receiver Sound is output through the receiver (home theater).
Setup You can set the Anynet+ (HDMI-CEC), auto turn off, and searching connections for 
using Anynet+.
TV Remote Control Buttons Available in Anynet +
 Mode
Device Type Operating Status Available Buttons
Anynet +
 Device After switching to the device, when the 
menu of the corresponding device is 
displayed on the screen.
Numeric buttons
▲/▼/◄/►/
ENTER 
 buttons
Color buttons / EXIT button
After switching to the device, while 
playing a file
 (Backward search) /  (Forward search)
 (Stop) /  (Play) /  (Pause)
Device with built-in Tuner After switching to the device, when you 
are watching a TV program  CH 
/ CH  button
Audio Device When Receiver is activated VOL –/ VOL +/ MUTE button
The Anynet +
 function only works when the active source on the TV remote control is set to TV.
The 
 button works only while in the recordable state.
You cannot control Anynet+ devices using the buttons on the TV. You can control Anynet +
 devices only using the TV 
remote control.
The TV remote control may not work under certain conditions. In this case, r\
eselect the Anynet +
 device.
The Anynet +
 functions do not operate with other manufacturers’ products.
The 
,  operations may differ depending on the device.
➣
➣
➣
➣
➣
➣
Recording
You can make a recording of a TV program using a Samsung recorder.
1.
  Press the TOOLS  button.
2.
    Press the ▲ or ▼ button to select Recording Immediately and press the ENTER  button. Recording begins.
When there is more than one recording device
When multiple recording devices are connected, the recording devices are\
 listed. 
Press the ▲ or ▼ button to select a recording device and press the  ENTER 
 button. Recording begins.
When the recording device is not displayed
Select “Device List” and press the red button to search devices.
 Press the EXIT button to exit.
You can record the source streams by selecting “Record” after press\
ing the  TOOLS button.
Pressing the  
 button will record whatever you are currently watching. If you are watch\
ing video from another 
device, the video from the device is recorded.
Before recording, check whether the antenna jack is properly connected t\
o the recording device. To properly connect 
an antenna to a recording device, refer to the recording device’s users manual.
➣
➣
➣
TOOLS
  Device List  Record  Timer Recording  Receiver  : OffPicture Mode  : StandardSound Mode  : CustomSleep Timer  : OffChannel Add/Delete▼
e  ExitEnter
Move
BN68-01392D-01Eng-0221.indd   632008-02-22   ¿ÀÈÄ 5:44:50 
						

							English - 64
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1.
   Press the TOOLS  button. Press the ▲ or ▼ button to select “Receiver”.
2.
    Press the ◄ or ► button to select to “On”. 
Now you can listen to sound through the receiver.
3.
  Press the EXIT button to exit.
If your receiver supports audio only, it may not appear in the device list.
The receiver will work when you have properly connected the Optical IN j\
ack of the 
receiver to the Optical Out jack of the TV.
When the receiver (home theater) is set to On, you can hear sound outp\
ut from the 
TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 
channel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected 
to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
When listening through the receiver, there are restrictions for using the PIP and audio-related (MTS, Preferred 
language) menus.
If there is a power interruption to the TV when the “Receiver” is set to “On” (by disconnecting the\
 power cord or a 
power failure), the “TV Speaker” may be set to “Off” when you turn the TV on again. (see page 32)
➣
➣
➣
➣
➣
Troubleshooting for Anynet +
 
Symptom Solution
Anynet +
 does not work. Check if the device is an Anynet+ device. The Anynet +
 system supports Anynet +
 
devices only.
Connect only one receiver (home theater).
Check if the Anynet +
 device power cord is properly connected.
Check the Anynet +
 device’s Video/Audio/HDMI 1.3 cable connections.
Check whether Anynet +
 (HDMI-CEC) is set to On in the Anynet +
 setup menu.
Check whether the TV remote control is in TV mode.
Check whether it is Anynet +
 exclusive remote control.
Anynet +
 doesn’t work in certain situations. (Searching channels, Plug & Pla\
y, etc.)
When connecting or removing the HDMI 1.3 cable, please make sure to sear\
ch 
devices again or turn your TV off and on again.
Check if the Anynet +
 Function of Anynet +
 device is set on.
•
•
•
•
•
•
•
•
•
•
I want to start Anynet +
. Check if the Anynet +
 device is properly connected to the TV and check if the 
Anynet +
 (HDMI-CEC) is set to On in the Anynet +
 Setup menu.
Press the TV button on the TV remote control to switch to TV. Then press the 
TOOLS  button to show the Anynet +
 menu and select a menu you want.•
•
I want to exit Anynet +
. Select View TV in the Anynet +
 menu. 
Press the SOURCE button on the TV remote control and select a device other 
than Anynet +
 devices.
Press CH, CH LIST, PRE-CH, and FAV.CH to change the TV mode. 
(Note that the channel button operates only when a tuner-embedded Anynet +
 
device is not connected.)•
•
•
The message Connecting to 
Anynet +
 device... appears on the 
screen. You cannot use the remote control when you are configuring Anynet+ or 
switching to a view mode.
Use the remote control when the Anynet
+
 setting or switching to view mode is 
complete.•
•
The Anynet +
 device does not play. You cannot use the play function when Plug & Play is in progress.
The connected device is not 
displayed. Check whether or not the device supports Anynet
+
 functions. 
Check whether or not the HDMI 1.3 cable is properly connected.
Check whether Anynet +
 (HDMI-CEC) is set to On in the Anynet +
 setup menu.
Search Anynet +
 devices again.
You can connect an Anynet +
 device using the HDMI 1.3 cable only. Some HDMI 
cables may not support Anynet +
 functions.
If it is terminated by an abnormal situation such as disconnecting the H\
DMI cable 
or power cord or a power failure, please repeat the device scan.
•
•
•
•
•
•
The TV program cannot be 
recorded. Check whether the antenna jack on the recording device is properly conne\
cted.
The TV sound is not output 
through the receiver. Connect the optical cable between TV and the receiver.
TOOLS
  Device List  Record  Timer Recording  Receiver 
◄ Off ►Picture Mode  : StandardSound Mode  : CustomSleep Timer  : OffChannel Add/Delete▼
e  Exit
MoveAdjust
BN68-01392D-01Eng-0221.indd   642008-02-22   ¿ÀÈÄ 5:44:50 
						

							English - 6
Troubleshooting
If the TV seems to have a problem, first try this list of possible problems and solutions. If none of these troubleshooting tips 
apply, call Samsung customer service at 1-800-SAMSUNG.
ProblemPossible Solution
Poor picture. Try another channel.
Adjust the antenna.
Check all wire connections.
Poor sound quality. Try another channel.
Adjust the antenna.
No picture or sound. Try another channel.
Press the SOURCE button.
Make sure the TV is plugged in.
Check the antenna connections.
No sound or sound is too low at 
maximum volume. First, check the volume of units connected to your TV (digital broadcasting 
receiver, DVD, cable broadcasting receiver, VCR, etc.). Then, adjust the TV 
volume accordingly.
Picture rolls vertically. Check all wire connections.
The TV operates erratically. Unplug the TV for 30 seconds, then try operating it again.
The TV won’t turn on. Make sure the wall outlet is working.
Remote control malfunctions. Replace the remote control batteries.
Clean the upper edge of the remote control (transmission window).
Check the battery terminals.
“Check signal cable” message. Ensure that the signal cable is firmly connected to the PC source.
“Not Supported Mode” message. Check the maximum resolution and connected device’s Video frequency.
Compare these values with the data in the Display Modes.
Digital broadcasting screen problem. Please check the digital signal strength and input antenna.
The image is too light or too dark. Adjust the Brightness and Contrast.
Adjust the Fine tuning.
Black bars on the screen. Make sure the broadcast you’re receiving is High Definition (HD).
HD channels sometimes broadcast Standard Definition (SD) programming, 
which can cause black bars.
Set your cable/satellite box to stretch or widescreen mode to eliminate \
the bars.
Picture has a Red/Green or Pink tint. Make sure the Component cables are connected to the correct jacks.
Closed Captioning not working. If you are using a Cable/Satellite box, you must set Closed Captioning o\
n the 
box, not your TV.
Snowy picture. Your cable box may need a firmware upgrade. Please contact your Cable 
company.
Ghosting on picture. This is sometimes caused by compatibility issues with your cable box.
Try connecting Component cables instead.
Horizontal bars appear to flicker, jitter 
or shimmer on the image. Adjust the Coarse tuning and then adjust the Fine tuning.
Vertical bars appear to flicker, jitter or 
shimmer on the image. Adjust the Coarse tuning and then adjust the Fine tuning.
Screen is black and power indicator 
light blinks steadily. On your computer check: Power, Signal Cable.
The TV is using its power management system.
Move the computer's mouse or press any key on the keyboard.
Appendix
BN68-01392D-01Eng-0221.indd   652008-02-22   ¿ÀÈÄ 5:44:50 
						

							English - 66
ProblemPossible Solution
Image is not stable and may appear 
to vibrate when you have a computer 
connected to the PC input. If the setting is not correct, use your computer utility program to chan\
ge the 
display settings.
Your TV supports multiscan display functions within the following 
frequency domain:
Horizontal frequency (kHz) 30~60
Vertical frequency (Hz) 60~75
PC Maximum refresh rate (at 60 Hz) 1920 x 1080
➣
Image is not centered on the screen. Adjust the horizontal and vertical position.
The screen position must be adjusted on the output source (i.e. STB) w\
ith a 
digital signal.
The picture appears distorted in the 
corner of the screen. If “Just Scan” is selected with some external devices, the picture\
 may appear 
distorted in the corner of the screen. This symptom is caused by the external 
devices, not TV.
The “Resets all settings to the default 
values.” message appears. This appears when you press and hold the 
EXIT button for a while. The product 
settings are reset to the factory defaults.
This TFT LCD panel uses a panel consisting of sub pixels (6 220 800) which req\
uire sophisticated technology to produce. 
However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of 
the product.
BN68-01392D-01Eng-0221.indd   662008-02-22   ¿ÀÈÄ 5:44:51 
						

							English - 67
Installing the Stand
1. Attach your LCD TV to the stand.Two or more people should carry the TV. 
Make sure to distinguish between the front and back of the stand  when attaching it.
To make sure the TV is installed on the stand at a proper level, do not apply excess downward pressure to the 
upper left of right sides of the TV.
2.
  Fasten two screws at position 1 and then fasten two screws at position 2.
Stand the product up and fasten the screws. If you fasten the screws wit\
h the LCD TV placed down, it may lean to 
one side.
➣
➣
➣
➣
Disconnecting the Stand
1.  Remove four screws from the back of the TV.
2. Separate the stand from the TV.
Two or more people should carry the TV. 
3.
 Cover the bottom hole with the cover.
 
➣
BN68-01392D-01Eng-0221.indd   672008-02-22   ¿ÀÈÄ 5:44:51 
						

							English - 68
Auto Wall-Mount Adjustment (Sold separately) 
Once the auto wall mount is installed, your TV’s position can be easily adjusted.
TV Rear PanelAuto Wall-Mount
EX-LINK Cable  (Not supplied)
Entering the menu
1.   Press the ▲, ▼, ◄ or ► button on your remote control.
The Wall Mount Adjustment screen is displayed.
If the Wall Mount Adjustment screen is not displayed when clicking on 
a direction button while watching your TV, use the menu to display that 
screen. 
Press the MENU button to display the menu. Press the ▲ or ▼ button to select 
“Setup”, then press the ENTER 
 button. 
Press the ▲ or ▼ button to select “External Settings”, then press the ENTER 
 
button.
Press the ▲ or ▼ button to select “Wall-Mount Adjustment”, then press the 
ENTER 
 button.
Remembering the Position
2.   Adjust to the desired position using the ▲,▼,◄,► buttons. If you press an arrow button when no OSD is displayed on the TV screen, 
the Adjustment screen appears.
Press the INFO button to reset. Press the ◄ or ► button to select “Yes”, 
then press the ENTER 
 button. The position is initialized to the default 
setting.
3.   Press the Blue button. Press the ▲ and ▼ buttons to select a save mode from either Position 1, 
Position 2 or Position 3 in order to save the current position.
To not save the current position, press the  RETURN button. 
When selecting a save mode, you cannot use the Color buttons.
4.   Press the ENTER 
 button to save.
When Position1 is selected, the message “Current position saved as 
Position1” is displayed.
5.   Press the ENTER 
 button.
The saved Position appears on the left side of the OSD.
Moving to the remembered position
1.   Complete Step 1 of “Entering the menu”.
2.   Pressing a Color (Red, Green, Yellow) button moves the auto wall mount to  the saved position.
You can move the wall mount to one of the 3 pre-set positions by pressing\
 the Red (Position 1), Green (Position 2) 
or Yellow (Position 3) buttons.
If you adjust the position after moving to a pre-set position, the posit\
ion display will disappear.
For installation, refer to the Installation Manual provided with the wal\
l mount.
For product installation and the installation and moving of the wall mou\
nt, make sure to consult a specialized 
installation company.
This installation manual is to be used when attaching the wall mount to \
a wall. When attaching to other building 
materials, please contact your nearest dealer.
The auto wall mount will not work when Anynet +
 is operating.
LN37A530P1F, LN40A530P1F and LN46A530P1F models are not compatible with the older wall mount model 
(WMN5090A).
➣
➣
•
•
•
➣
➣
➣
➣
➣
➣
➣
➣
➣
➣
➣
➣
➣
Setup
V-Chip 
Caption
External	Settings	 	 ►
Entertainment  : Off
Energy Saving  : Off
PIP
SW Upgrade
External Settings
Melody  : 
 Medium
Wall-Mount Adjustment
Return
Enter
Move
Save
Select a mode to Save.
Position1
Position2
Position
 Adjust    Enter Return
Wall-Mount Adjusment
Adjust   Save  CenterINFO   1    2    Position
Wall-Mount Adjusment
Adjust  Save  CenterINFO   1    2    
Position1
Position
BN68-01392D-01Eng-0221.indd   682008-02-22   ¿ÀÈÄ 5:44:53