Ricoh Projector PJ WX4141N User Manual

5.Turn the power switch of the electronic pen to "On".
The communication indicator on the electronic pen will then flicker.
If the communication indicator fails to flicker, check that the rechargeable battery is installed in the electronic pen. If a battery is installed, recharge it. For about the electronic pen, see page 92
"Using the Electronic Pen".
6. Point the pen nib toward the projected screen.
• If registration succeeds
The projected computer screen pointer moves according to the...

• If the electronic pen is not recognized correctly after the direction of the pen is correctedor even when you hold the electronic pen correctly, check the procedure from Step 1 by
referring to page 98 "When You Cannot Use the Interactive Function".
Installing RICOH PJ Interactive Software
RICOH PJ Interactive Software allows you to write and draw on a projection screen. When you use
RICOH PJ Interactive Software, install it on a computer. For details about how to use RICOH PJ Interactive...

7.Select "I accept the terms in the license agreement", and then click [Next].
8. Specify the installation folder, and then click [Next].
9. Click [Install].
10. Click [Finish].
• If the [User Account Control] dialog box appears during the installation procedure, click [Yes] or
[Continue].
• To uninstall RICOH PJ Interactive Software, use the program delete function in [Control Panel] to delete "RICOH PJ Interactive Software".
Preparations for Using the Interactive Function
91   

Using the Electronic Pen
This section introduces the names of the parts of the electronic pen and explains how to charge it.
After you finish setting up the interactive function, insert the computer USB adapter into the computer.
After the computer recognizes the electronic pen, you can use it to perform operations on the projected
screen. For details about the electronic pen, see page 88 "Enabling the Projector to Recognize the
Electronic Pen".
Communication between the electronic pen, the...

When the projector recognizes the electronic pen, the indicator lights up in green or flickers rapidly.
7. USB connecter Used to connect the electronic pen charge cable. See page 97 "Recharging the Electronic Pen".
8. Power switch Switches the power of the electronic pen between on and off.
How to Use the Electronic Pen
When the pen nib is pointed toward the screen projected by the projector in Interactive Mode, the electronic pen is recognized and the pointer on the projected computer screen can...

To align the point position of the electronic pen with the pen nib switch, and not the center of the
pen, use the point adjustment button to move the point position up.
When the projector is installed on a wall or ceiling
When the projector is installed on a wall or ceiling, hold the electronic pen upside down to
eliminate the shadow that appears on the screen.
To align the point position with the pen nib switch while holding the electronic pen upside down,
use the point adjustment button to move the...

• The electronic pen can only be used while the projector is in Interactive Mode. For details abouthow to configure the projector, see page 84 "Enabling Interactive Mode".
Installing a Rechargeable Battery into the Electronic Pen
• For safe operation, follow the warnings below regarding the batteries. If you use the batteries incorrectly, it may result in fire or injury due to batteries leaking or exploding.
• Do not use batteries other than the ones specified.
• Do not mix and use batteries that...

1.Check the electronic pen to make sure that the power is off.
2.Push down A and slide the battery cover to remove it.
3.Install a battery.
Check that the battery has been installed in the right direction.
6. Using the Interactive Function (RICOH PJ WX4141NI only)
96CWD029 A                 
CWD025 CWD026   

4.Re-install the battery cover.
• For details about what to do if a battery has leaked, see page 147 "Operating Precautions".
Recharging the Electronic Pen
Insert an electronic pen charge cable into a USB port on the computer and connect the electronic pen.
The battery indicator keeps lighting while charging and goes off when the charge is completed.
Using the Electronic Pen
97CWD027  CWD009   

When You Cannot Use the Interactive Function
If you cannot use the interactive function, follow the steps below in the specified order to troubleshoot
the problem.StepCheck itemSolutions1Check the projector to make
sure that power is supplied
to it.If the projector is not supplied with power, check the power
cord for connection and turn on the power. To connect the
cord and turn on the power correctly, see page 35 "Turning
On the Projector".2Check to see whether the
projector is in Interactive...