Ricoh Projector PJ WX4141N User Manual

2.Connect the USB device to the USB port on the projector.
Check the port orientation before connecting.
3. Press the [Power] button.
The confirm screen appears.
4. Press the [Power] button.
The projector beeps and enters the standby mode.
• For details about the USB devices and files supported by the projector, see page 47 "Requirements for Projecting Images from a USB Device".
• Do not disconnect the power cord when using the power timer function. The projector cannot start if the power cord is...

WipeThe current image is wiped off by the next image.
FadeThe current image fades out and the next image fades in.
1.Press the [Menu] button.
2. Select [Network/USB Settings], and then press the [
] button.
3.Select [USB Settings], and then press the [Enter] button.
4. Select [Settings], and then press the [
] button.
5. Select [Display Effect], and then press the [Enter] button.
4. Useful Functions
60CZE163 CZE164 CZE165  CZE158    

6.Select a display effect, and then press the [Enter] button.
7.Press the [Menu] button.
8. Select [Reflect], and then press the [Enter] button.
9. Press the [Menu] button to close the menu screen.
Adjusting the slide show switching interval
You can adjust the slide show switching interval from 5 to 999 seconds. 1. Press the [Menu] button.
2. Select [Network/USB Settings], and then press the [
] button.
3.Select [USB Settings], and then press the [Enter] button.
4. Select [Settings], and then press the...

5.Select [Display Interval (sec.)], and then press the [Enter] button.
6. Specify a slide show switching interval.
7. Press the [Menu] button.
8. Select [Reflect], and then press the [Enter] button.
9. Press the [Menu] button to close the menu screen.4. Useful Functions
62  

Specifying the Sound Quality
You can select a sound quality setting for the built-in speaker that is applicable for the type of audio that
you are playing. This makes it easier to hear the audio that is playing.
Setting the Sound Quality for Giving a Presentation
If [Narration] is specified for the sound quality, the projector plays dialog clearly. This mode is useful
when you give a presentation using the microphone connected to the projector, for example.
1. Press the [Sound] button.
The sound quality...

4. Useful Functions
64  

5. Using the Projector via a Network
This chapter explains the settings for using the projector via a network. This chapter also explains the
operations that use QuickProjection.
Before Connecting to a Network
Connecting an Ethernet Cable
• Do not place the power cord and connection cable in a way that might cause someone to trip and fall. The machine might fall over and cause an injury.
The projector is compatible with 10BASE-T, 100BASE-TX, and 1000BASE-T Ethernet interfaces.
Status of the network...

1.Insert the Ethernet cable into the LAN port.
2.Connect the other end of the Ethernet cable to a network device such as a hub.
• Use an Ethernet cable that is shielded.
Precautions for Using a Wireless LAN
• Do not use a wireless LAN if there is electromagnetic interference from other equipment. Doing so may cause an accident due to the other equipment malfunctioning from the electromagnetic
interference.
Wireless uses radio waves to exchange information instead of an Ethernet cable. The wireless LAN...

Connecting the Projector to a Network
To connect the projector to a network, you must specify network settings such as an IP address. The required settings differ depending on the network environment and how you use the projector.
You can configure the required settings easily by using Network Setting Wizard. For details about how
to open Network Setting Wizard, see page 68 "Opening Network Setting Wizard".
To connect to a wired LAN
Connect an Ethernet cable to the projector, and then configure...

Opening Network Setting Wizard
You can open Network Setting Wizard on the menu screen.1. Press the [Menu] button.
2. Select [Network/USB Settings], and then press the [
] button.
3. Select [Network Settings], and then press the [Enter] button.
4. Select [Setup Wizard], and then press the [
] button.
5. Select [Network Setting Wizard], and then press the [Enter] button.
Network Setting Wizard appears.
Configuring the Wired LAN Settings
Connect an Ethernet cable to the projector before configuring the...