Ricoh Projector PJ WX4141N User Manual

							2.Connect the USB device to the USB port on the projector.
Check the port orientation before connecting.
3. Press the [Power] button.
The confirm screen appears.
4. Press the [Power] button.
The projector beeps and enters the standby mode.
• For details about the USB devices and files supported by the projector, see page 47 "Requirements for Projecting Images from a USB Device".
• Do not disconnect the power cord when using the power timer function. The projector cannot start if the power cord is disconnected.
Customizing a Slide Show
You can customize the display effect and display interval for a slide show. These functions are useful for
decorating shop windows more effectively.
Changing the display effect for a slide show
You can change the display effect for switching images. The available display effects are the following:
Push
The current image is pushed off by the next image.
Projecting Images in a Slide Show
59CZE121     
						

							WipeThe current image is wiped off by the next image.
FadeThe current image fades out and the next image fades in.
1.Press the [Menu] button.
2. Select [Network/USB Settings], and then press the [
] button.
3.Select [USB Settings], and then press the [Enter] button.
4. Select [Settings], and then press the [
] button.
5. Select [Display Effect], and then press the [Enter] button.
4. Useful Functions
60CZE163 CZE164 CZE165  CZE158    
						

							6.Select a display effect, and then press the [Enter] button.
7.Press the [Menu] button.
8. Select [Reflect], and then press the [Enter] button.
9. Press the [Menu] button to close the menu screen.
Adjusting the slide show switching interval
You can adjust the slide show switching interval from 5 to 999 seconds. 1. Press the [Menu] button.
2. Select [Network/USB Settings], and then press the [
] button.
3.Select [USB Settings], and then press the [Enter] button.
4. Select [Settings], and then press the [
] button.
Projecting Images in a Slide Show
61CZE161  CZE158    
						

							5.Select [Display Interval (sec.)], and then press the [Enter] button.
6. Specify a slide show switching interval.
7. Press the [Menu] button.
8. Select [Reflect], and then press the [Enter] button.
9. Press the [Menu] button to close the menu screen.4. Useful Functions
62  
						

							Specifying the Sound Quality
You can select a sound quality setting for the built-in speaker that is applicable for the type of audio that
you are playing. This makes it easier to hear the audio that is playing.
Setting the Sound Quality for Giving a Presentation
If [Narration] is specified for the sound quality, the projector plays dialog clearly. This mode is useful
when you give a presentation using the microphone connected to the projector, for example.
1. Press the [Sound] button.
The sound quality selection screen appears at the bottom of the screen.
2. Select [Narration] (
) using the [] and [] buttons.
Setting the Sound Quality for Playing Music
If [Music] is specified for the sound quality, the projector plays music dynamically. This mode is useful for music videos, for example. This mode is also useful if you want to decorate a shop window with video
and music.
1. Press the [Sound] button.
The sound quality selection screen appears at the bottom of the screen.
2. Select [Music] (
) using the [] and [] buttons.
Specifying the Sound Quality
63        
						

							4. Useful Functions
64  
						

							5. Using the Projector via a Network
This chapter explains the settings for using the projector via a network. This chapter also explains the
operations that use QuickProjection.
Before Connecting to a Network
Connecting an Ethernet Cable
• Do not place the power cord and connection cable in a way that might cause someone to trip and fall. The machine might fall over and cause an injury.
The projector is compatible with 10BASE-T, 100BASE-TX, and 1000BASE-T Ethernet interfaces.
Status of the network connection
You can confirm the status of the network connection by the patterns in which the LEDs on the
Ethernet interface light up. If the projector is not connected to a network, no LEDs light up.
1. When 1000BASE-T is active (orange and green LEDs light up)
2. When 100BASE-TX is active (orange LED lights up) 3. When 10BASE-T is active (green LED lights up)
65 CLB072
123   
						

							1.Insert the Ethernet cable into the LAN port.
2.Connect the other end of the Ethernet cable to a network device such as a hub.
• Use an Ethernet cable that is shielded.
Precautions for Using a Wireless LAN
• Do not use a wireless LAN if there is electromagnetic interference from other equipment. Doing so may cause an accident due to the other equipment malfunctioning from the electromagnetic
interference.
Wireless uses radio waves to exchange information instead of an Ethernet cable. The wireless LAN
radio waves pass through barriers such as walls within a fixed area, so the following problems may
occur:
Leak of Personal Information
• Information such as IDs, passwords, credit card numbers, and the contents of e-mails, etc.,may be stolen by a third party.
Illegal Access to the Network
• Data and systems may be corrupted or manipulated by a virus.
• An imposter may access information illegally. • Confidential information may be accessed illegally.
To minimize the possibility of these problems occurring, it is recommended to check the functions built into the wireless LAN devices, such as the projector and wireless LAN access points, and to specify
security settings.
5. Using the Projector via a Network
66CZE122     
						

							Connecting the Projector to a Network
To connect the projector to a network, you must specify network settings such as an IP address. The required settings differ depending on the network environment and how you use the projector.
You can configure the required settings easily by using Network Setting Wizard. For details about how
to open Network Setting Wizard, see page 68 "Opening Network Setting Wizard".
To connect to a wired LAN
Connect an Ethernet cable to the projector, and then configure the network settings in [Wired LAN]
on Network Setting Wizard. For details about how to configure the wired LAN network settings,
see page 68 "Configuring the Wired LAN Settings".
To connect to a wireless LAN in infrastructure mode
In infrastructure mode, the projector can communicate with networks in which both wireless and
wired LAN devices are connected via a wireless LAN access terminal. It is necessary to use greater security since all communication is via a network. Use infrastructure mode in environments in whicha wireless LAN has already been configured.
Configure the network settings in [Wireless LAN (Infrastructure)] on Network Setting Wizard. The
setting method differs depending on the network environment.
• Configuring the settings by Simple Wireless LAN Setup If the access point is compliant with the simple wireless LAN setup function, you can configure
the network settings easily. This function acquires the wireless LAN settings registered in the access point, and configures those settings for the projector automatically. You can configure
the settings without entering the SSID and the network key manually. For details, see
page 69 "Configuring the settings by Simple Wireless LAN Setup".
• Configuring the settings manually You can configure the network settings by selecting the network to connect to from the
available network list. Up to 10 networks are displayed in the list in radio field intensity order.
If you want to connect to a network that is not displayed in the list or is not broadcasting its
SSID, enter the SSID manually. For details, see page 70 "Configuring the settings manually".
To connect to a wireless LAN in ad hoc mode
In ad hoc mode, the projector can communicate with the computer directly, and not via an access
point. No other equipment is required, so this mode is suited for locations that have no network
environment. As the radio wave range is limited, use an office or conference room with a good line
of sight.
Configure the network settings in [Wireless LAN (Adhoc)] on Network Setting Wizard. For details
about how to configure the network settings for a wireless LAN in ad hoc mode, see page 71
"Configuring the Wireless LAN Settings for Ad Hoc Mode".
Connecting the Projector to a Network
67  
						

							Opening Network Setting Wizard
You can open Network Setting Wizard on the menu screen.1. Press the [Menu] button.
2. Select [Network/USB Settings], and then press the [
] button.
3. Select [Network Settings], and then press the [Enter] button.
4. Select [Setup Wizard], and then press the [
] button.
5. Select [Network Setting Wizard], and then press the [Enter] button.
Network Setting Wizard appears.
Configuring the Wired LAN Settings
Connect an Ethernet cable to the projector before configuring the settings.
Contact your network administrator for the information required for configuring network settings.
1. Select [Wired LAN] on Network Setting Wizard, and then press the [Enter] button.
2.Select [Disable DHCP (Manual Settings)] or [Enable DHCP (Auto Settings)], and then press
the [Enter] button.
If you select [Enable DHCP (Auto Settings)], proceed to Step 6.
3. Specify the projector's IP address.
4. Specify the subnet mask.
5. Using the Projector via a Network
68