Ricoh Projector PJ WX4141N User Manual

							ItemDefaultProjection ModeSelect the projection method according to how the projector is
positioned.
• Standard Select this mode when the projector is placed in front of a screen.
• Rear Select this mode when the projector is placed behind a screen.
• Ceiling Select this mode when the projector is mounted on the ceiling in front
of a screen.
• Rear Ceiling Select this mode when the projector is mounted on the ceiling behind
a screen.StandardRemote Control ID
Select the projector remote control ID. Specify the ID for each projectorwhen operating multiple projectors using one remote control.
• 1
• 2
• 3
• 41Power On Method
Select the power on method of the projector.• Manual Turn the projector on when the [Power] button is pressed.
• Auto. Automatically turn on the projector when the power cord is
connected.ManualStart on Input Detection
Specify whether or not to start projecting automatically if the image
signals are input while in standby.OnDefault Settings 2 Menu
119  
						

							ItemDefaultHigh Altitude ModeThe number of fan rotations is high when set to [On]. The air is thin at high
elevations, so the cooling efficiency of the projector is reduced. Select
[On] when using the projector at an altitude of more than 1,500 meters
(4,921 feet). Do not select [On] when the altitude is less than 1,500
meters (4,921 feet).OffKey Lock
Specify whether or not to lock the buttons on the control panel. You canchange this setting to [Off] by pressing the [AV Mute] button on the
projector's control panel for 10 seconds.OffReset All
Reset all menus to their defaults.
This function cannot restore the default settings of [User Logo] in [Default Settings 1], [Current Time] and [Startup Password] in [Default Settings 2],[Administrator Authentication] and [Administrator Password] in [NetworkApplication Settings].-Startup Password > Register Password
Enter a 6-digit password. The current password is required to change thepassword.000000Startup Password > Password Protect
Specify whether or not to enter a password when the projector is turnedon. If this is selected, a password must be entered when the projector is turned on after the power cord has been unplugged. However, a
password is not required when turning the projector on from the standby mode.
A password is required to change this setting.Off7. Changing the Projector Settings
120  
						

							USB Settings Menu
This section explains the items in the USB Settings menu under the Network/USB Settings menu tab.
You can also specify and check the items in the USB Settings menu using Web Image Monitor.
However, the following items are available only on the menu screen.
• [Remove USB Mem.] in [Settings]
• [USB Memory Free Space (KB)] and [USB Memory Access Status] in [Display Status]
On Web Image Monitor, you can check [Network/USB Func. Firmware Version] and [Energy Saving
IO Firmware Version] on the top page.
For details about Web Image Monitor, see page 159 "Managing the Projector Using Web Image Monitor".
Settings
Still Image
ItemDefaultDisplay Effect Select the display effect for switching the image.• None
• Push The current image is pushed off by the next image.
• Wipe The current image is wiped off by the next image.
• Fade The current image fades out and the next image fades in.NoneDisplay Interval (sec.)
Enter the slide show switching interval from 5 to 999 seconds.5 seconds
Moving Image
ItemDefaultRepeat Specify whether or not to repeat video playback.OffUSB Settings Menu
121  
						

							CommonItemDefaultAuto Start SlideshowSpecify whether or not to start a slide show automatically when the
projector is connected to the USB device.OffRemove USB Mem.
The USB device can be removed when this command is executed.-
Display Status
USB Memory
ItemDefaultUSB Memory Free Space (KB)Display the space available on the USB device (Displayed in KB).-USB Memory Access Status Display whether or not the USB device can be accessed.-
Firmware Version
ItemDefaultNetwork/USB Func. Firmware VersionDisplay the firmware version of the network and USB functions.-Energy Saving IO Firmware Version Display the energy-saving IO firmware version.-7. Changing the Projector Settings
122  
						

							Network Settings Menu
This section explains the items in the Network Settings menu under the Network/USB Settings menu tab.
You can also specify and check the items in the Network Settings menu using Web Image Monitor.
However, the following items are available only on the menu screen.
• [Simple Wireless LAN Setup] and [Reset Wireless LAN Settings] in [Wireless LAN]
• [Import Device Certificate] and [Certificate List] in [LAN Common] • [Network Setting Wizard] in [Setup Wizard]
On Web Image Monitor, you can check [Network/USB Func. Firmware Version] and [Energy Saving IO Firmware Version] on the top page.
For details about Web Image Monitor, see page 159 "Managing the Projector Using Web Image Monitor".
Wired LAN
Wired LAN Settings
ItemDefaultTransmission Speed Select a wired LAN speed that matches your network environment. Itis recommended that [Auto-Negotiation] be selected.
• Auto-Negotiation
• 10BASE-T Full Duplex
• 10BASE-T Half Duplex
• 100BASE-TX Full Duplex
• 100BASE-TX Half DuplexAuto-Negotiation
TCP/IP Settings
ItemDefaultDHCP
Specify whether to enable or disable DHCP.
The IP address is allocated automatically from the DHCP server when
[Enable] is selected. When [Disable] is selected, enter the IP address,
subnet mask, and default gateway manually.EnableNetwork Settings Menu
123  
						

							ItemDefaultIP AddressEnter the projector's IP address.0.0.0.0Subnet MaskEnter the subnet mask.0.0.0.0Default GatewayEnter the default gateway.0.0.0.0
Wireless LAN
Simple Settings
ItemDefaultSimple Wireless LAN SetupAcquire the wireless LAN settings registered in the access point, and
specify infrastructure mode wireless LAN settings for the projector
automatically.
This function may not work depending on the access point.-
Wireless LAN Settings
ItemDefaultCommunication Mode
Select the wireless LAN communication mode.• Infrastructure Select this mode when you want to connect the projector to a
wireless LAN network. You need to specify [SSID] and items in
[Security] and [TCP/IP Settings] in this mode.
• Adhoc Select this mode when you want to connect the projector and
the computer directly. The projector specifies [SSID] and items in
[Security] and [TCP/IP Settings] automatically in this mode.Adhoc7. Changing the Projector Settings
124  
						

							ItemDefaultSSIDEnter the SSID to connect to a wireless LAN network when
[Infrastructure] is selected. Enter up to 32 characters.(blank)Channel
Select the channel to use when [Adhoc] is selected.
Select the channel that matches the type of wireless LAN being used.
The channels available might differ depending on the country. • 2.4 GHz: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 1111
Security
ItemDefaultAuthentication Method
Select the wireless LAN authentication method.• Open System
• WEP Shared Key
• WPA-PSK
• WPA2-PSKOpen SystemEncryption Method
Select the wireless LAN encryption method.
If you select [No Encryption], the communication is not encrypted.
[No Encryption] is selectable only when you select [Open System] in
[Authentication Method].
Select [WEP] when you select [Open System] or [WEP Shared Key]
in [Authentication Method].
Select [TKIP] or [CCMP] when you select [WPA-PSK] or [WPA2-PSK]
in [Authentication Method].
• No Encryption
• WEP
• TKIP
• CCMPNo EncryptionNetwork Settings Menu
125  
						

							ItemDefaultTransmission WEP Key NumberSelect the key number used to authenticate and encrypt transmissions
when you select [WEP] in [Encryption Method].
• 1
• 2
• 3
• 41Network Key
Enter the WEP key when you select [WEP Shared Key] or [Open
System] in [Authentication Method] and select [WEP] in [Encryption Method].
When using 64 bit WEP, up to 10 characters can be used for hexadecimal and up to 5 characters for ASCII. When using 128 bitWEP, up to 26 characters can be used for hexadecimal and up to 13characters for ASCII.
Enter PSK when [WPA-PSK] or [WPA2-PSK] is selected in
[Authentication Method].
When using a PSK, up to 64 characters can be used for hexadecimal
and 8 to 63 characters for ASCII.(blank)
TCP/IP Settings
ItemDefaultDHCP
Specify whether to enable or disable DHCP.
The IP address is allocated automatically from the DHCP server when
[Enable] is selected. If you select [Disable], manually enter the IP
address, subnet mask, and default gateway.DisableIP Address
Enter the projector's IP address.0.0.0.0Subnet MaskEnter the subnet mask.0.0.0.07. Changing the Projector Settings
126  
						

							ItemDefaultDefault GatewayEnter the default gateway.0.0.0.0
Reset Wireless LAN Settings
ItemDefaultReset Wireless LAN SettingsRestore all the wireless LAN settings to their defaults.-
LAN Common
Specify the wired LAN and wireless LAN settings.
Network Interface
ItemDefaultNetwork Interface
Select the network interface to be used.• Wired LAN
• Wireless LAN
• Wired LAN Priority Give priority to wired LAN if connected to the network via anEthernet cable. Disconnect the Ethernet cable when using a
wireless LAN.
• DisableWired LAN Priority
DNS Settings
ItemDefaultPrimary DNS Server Address
Enter the IP address of the primary DNS server.0.0.0.0Secondary DNS Server AddressEnter the IP address of the secondary DNS server.0.0.0.0Network Settings Menu
127  
						

							ItemDefaultHost NameDisplay the projector's host name.
The [Projector Name] in [Projector ID] is used as the projector’s host
name.-Domain Name
Enter the projector's domain name. Enter up to 63 characters.(blank)
Projector Search Settings
ItemDefaultProjector SearchSpecify whether or not to search for the projector automatically whenthe projector and the device connected to the projector are on the
same network.Enable
HTTP Client Settings
ItemDefaultHTTP Proxy Server Port
Enter an HTTP proxy server port that is between 1 and 65535.80HTTP Proxy Server NameEnter an HTTP proxy server name that is up to 128 characters.(blank)HTTP Proxy User Name Enter an HTTP proxy user name that is up to 31 characters.(blank)HTTP Proxy PasswordEnter an HTTP proxy password that is up to 31 characters.(blank)
HTTP Server Settings
ItemDefaultHTTP PortEnter an HTTP port that is between 1 and 65535.807. Changing the Projector Settings
128