Ricoh Mp 6002 User Guide

ProblemCausesSolutionsMisfeeds occur frequently.Paper of undetectable size
has been loaded.• Remove misfed paper. For details about removing jammed paper,
see "Removing Jammed Paper",
Troubleshooting
.
• If you load a paper size that is not selected automatically, you need
to specify the paper size with the
control panel. For details about
specifying paper size with the
control panel, see "Changing to a
Size That Is Not Automatically
Detected", Paper Specifications
and Adding Paper
....

ProblemCausesSolutionsCannot print in duplex
mode.You have selected a paper
tray that is not set for duplex
printing.Change the setting for "Apply Duplex"
in [System Settings] to enable duplex
printing for the paper tray. For details
about setting the "Apply Duplex", see
"Tray Paper Settings", Connecting the
Machine/ System Settings
.
Cannot print in duplex
mode.You have selected a paper
type that cannot be used for
duplex printing.In [Tray Paper Settings], select a paper
type...

ProblemCausesSolutions"Shutting down... Please
wait. Main power will be
turned off automatically.
Maximum waiting time: 3
minute(s)" appears.The shut down procedure
has begun because the main
power switch was turned off
while the machine was in
standby mode or performing
an operation.Follow the message that appears and
wait until the machine has shut down.
Do not turn on the main power switch
while this message is displayed. If the
main power switch has been turned on,
follow the message that...

• Using curled paper often causes misfeeds, soiled paper edges, or slipped positions whileperforming staple or stack printing. When using curled paper, take the stiffness out of the paper
with your hands to straighten out the curl, or load the paper up side down. Also, lay paper on a flat
surface to prevent paper from curling, and do not lean it against the wall.10. Troubleshooting
162  

When Messages Are Displayed on the Control
Panel
Messages Displayed When Using the Copy/Document Server Function
This section describes the machine's main messages. If other messages appear, follow their instructions.
• If you cannot make copies as you want because of the paper type, paper size or paper capacity problems, use recommended paper. For details about recommended paper, see p.135"Recommended Paper Sizes and Types".
• For messages that are not listed here, see p.156 "When You...

MessageCausesSolutions"Cannot punch this paper
size."The Punch function cannot
be used with paper size
selected.For details about paper, see
"Specifications for Punch Unit (Finisher
SR4060, Booklet Finisher SR4070)" or
"Specifications for Punch Unit (Finisher
SR4080)", Maintenance and
Specifications
.
"Cannot staple paper of this
size."The Staple function cannot
be used with paper size
selected.Select a proper paper size. For details
about paper, see "Specifications...

MessageCausesSolutions"Magazine or Booklet mode
is not available due to mixed
image mode."You selected the
"Magazine" or "Booklet"
function for originals
scanned using different
functions, such as copy and
printer.Make sure originals for the
"Magazine" or "Booklet" function are
scanned using the same function."Maximum number of sets is
n."
(A figure is placed at n.)The number of copies
exceeds the maximum copy
quantity.You can change the maximum copy...

MessageCausesSolutions"Rotate Sort is not available
with this paper size."A size of paper for which
Rotate Sort is not available is
selected.Select a proper paper size. For details
about paper, see "Sort", Copy/
Document Server
.
"Stapling capacity
exceeded."The number of sheets per set
is over the staple capacity.Check the stapler capacity. For details
about the stapler capacity, see
"Specifications for Finisher SR4060",
"Specifications for Booklet Finisher...

MessageCausesSolutions"Cannot print from the sub-
machine. Check the status of
the sub-machine."The sub-machine's User
Tools menu is open.Press the [User Tools/Counter] key to
close the User Tools menu."Cannot print from the sub-
machine. Sub-machine will
be disconnected."The sub-machine has
stopped due to power
failure or communication
error.Continue copying using the main
machine."Fold is available only when
Sort mode is selected in
Connect Copy."Sort has not been selected...

When the memory becomes full while using the copy/document server functionMessageCausesSolutions"Memory is full. nn originals
have been scanned. Press
[Print] to copy scanned
originals. Do not remove
remaining originals."
"n" in the message
represents a changeable
number.The scanned originals
exceed the number of pages
that can be stored in
memory.Press [Print] to copy scanned originals
and cancel the scanning data. Press
[Clear Memory] to cancel the scanning
data and not copy."Press...