Ricoh Mp 6002 User Guide

MessageCausesSolutions"Connection with the
remote machine has failed.
Check the remote machine
status."A network error occurred
while using the remote fax
function.• Check that the remote machine supports the remote fax function.
• Check that the remote machine is working normally.
• Check that the correct IP address or host name is set for the remote
machine in [System Settings]. For
details about these settings,
contact your administrator.
• Check that the LAN cable is correctly connected to...

MessageCausesSolutions"Remote fax is not available
because [User Code
Authentication] is active."The remote fax function does
not support User Code
Authentication.When using the remote fax function,
disable User Code Authentication. For
details about user code authentication,
see Security Guide
.
"Transfer error has occured.
Check the status of the
remote machine."A network error occurred
during transfer.• Check that the correct IP address or host name is set for the remote
machine in...

MessageCausesSolutions"Transmission cannot be
performed because the
certificate used for the S/
MIME signature is not
currently valid."The device certificate (S/
MIME) has expired.A new device certificate (S/MIME)
must be installed. For details about
how to install a device certificate (S/
MIME), see Security Guide
.
"The program contains a
destination(s) with a
certificate that is not
currently valid. The
destination(s) cannot be
recalled."The user certificate
(destination certificate)...

MessageCausesSolutions"E-mail TX Result cannot beset because the specified
destination's certificate is
not currently valid."The user certificate
(destination certificate) has
expired.For details about the user certificate
(destination certificate), see Security
Guide
.
"The program contains a
destination(s) that does not
have a certificate."There is no user certificate
(destination certificate).For details about the user certificate
(destination certificate), see Security
Guide
....

MessageCausesSolutions"XXX cannot be recalled
because there is a problem
with the device certificate
used for the S/MIME
signature."
(XXX indicates the e-mail
destination(s) or
destination(s) for E-mail TX
Result.)There is no device certificate
(S/MIME), or the certificate
is invalid.For details about the device certificate
(S/MIME), see Security Guide
.
"The PDF Digital Signature's
device certificate is not
currently valid. The e-mail
destination(s) which is
registered to the program...

• If "Check whether there are any network problems." appears, the machine is not correctlyconnected to the network or the settings of the machine are not correct. If you do not need to
connect to a network, you can specify the setting so this message is not displayed, and then the [Check Status] key no longer lights. For details about how to do this, see "Parameter Settings", Fax
. If you reconnect the machine to the network, be sure to set "Display" by configuring the
appropriate...

MessageStatus"Offline"The machine is offline."Please wait."This message might appear for a second or two while the machine is
preparing, performing initial adjustments, or adding toner. Wait a
while."Printing..."The machine is printing. Wait a while."Ready"This is the default ready message. The machine is ready for use. No
action is required."Resetting job..."The machine is resetting the print job. Wait until "Ready" appears on
the display...

MessageCausesSolutions"Cannot connect with the
Bluetooth interface. Check
the Bluetooth interface."• The Bluetooth interface unit was installed while
the machine was turned
on.
• The Bluetooth interface unit was removed while
the machine was turned
on.Turn off the main power switch, and then confirm that the Bluetooth
interface unit was installed correctly.
And then, turn on the main power
switch again. If the message appears
again, contact your service
representative."Hardware Problem:...

MessageCausesSolutions"Hardware Problem:
Wireless Card"
(A "wireless LAN board" or
"Bluetooth interface unit" is
referred to as a "wireless
card".)• The Bluetooth interface unit was connected
while the machine was
turned on.
• The Bluetooth interface unit was removed whilethe machine was turned
on.Turn off the main power switch, and
then confirm the Bluetooth interface unit
is inserted correctly. And then, turn on
the main power switch again. If the
message appears again,...

MessageCausesSolutions"Problem: Printer Font Error"An error has occurred in the
font settings.Contact your service representative."Problems with the wireless
card. Please call service."
(A "wireless LAN board" or
"Bluetooth unit" is referred to
as a "wireless card".)The machine has detected a
Bluetooth failure, or it could
not detect a Bluetooth unit. It
may be incorrectly installed.Check that the Bluetooth unit is installed
properly, or contact your service...