Ricoh Aficio MP2510SP User Manual

							Network Settings
33
1
❖[Network] → [NW Frame Type] → [Ethernet 802.2]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[Network] → [NW Frame Type] → [Ethernet 802.3]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[Network] → [NW Frame Type] → [Ethernet SNAP]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[Network] → [SMB Computer Name]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[Network] → [SMB Work Group]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[Network] → [Ethernet Speed]
 Web Image Monitor: Cannot be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[Network] → [LAN Type] → [Ethernet]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[Network] → [LAN Type] → [IEEE 802.11b]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting the Machine
34
1
❖[Network] → [Ping Command]
 Web Image Monitor: Cannot be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[Network] → [Permit SNMP V3 Communication] → [Encryption Only]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[Network] → [Permit SNMP V3 Communication] → [Encryption / Clear Text]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[Network] → [Permit SSL / TLS Communication] → [Ciphertext Only]
 Web Image Monitor: Cannot be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[Network] → [Permit SSL / TLS Communication] → [Ciphertext Priority]
 Web Image Monitor: Cannot be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[Network] → [Permit SSL / TLS Communication] → [Ciphertext / Clear Text]
 Web Image Monitor: Cannot be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[Network] → [Host Name]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Can be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[Network] → [Machine Name]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Settings
35
1
❖[IEEE 802.11b] → [Communication Mode]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[IEEE 802.11b] → [SSID Setting]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[IEEE 802.11b] → [Channel]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[IEEE 802.11b] → [WEP (Encryption) Setting]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[IEEE 802.11b] → [Transmission Speed]
 Web Image Monitor: Cannot be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Can be used for specifying the setting.
❖[File Transfer] → [SMTP Server]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [SMTP Authentication]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [POP before SMTP]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting the Machine
36
1
❖[File Transfer] → [Reception Protocol]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [POP3 / IMAP4 Settings]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [Administrators E-mail Address]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [E-mail Communication Port]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [E-mail Reception Interval]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [Max. Reception E-mail Size]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [E-mail Storage in Server]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [Default User Name / Password (Send)]
 Web Image Monitor: Can be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Settings
37
1
❖[File Transfer] → [Fax E-mail Account]
 Web Image Monitor: Cannot be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [Scanner Recall Interval Time]
 Web Image Monitor: Cannot be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
❖[File Transfer] → [Number of Scanner Recalls]
 Web Image Monitor: Cannot be used for specifying the setting.
 SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
 telnet: Cannot be used for specifying the setting.
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting the Machine
38
1Connecting the Machine to a Telephone 
Line and TelephoneThis section describes how to connect the machine to the telephone lines and se-
lect the line type.
Connecting the Telephone Line
This section describes how to connect the machine to the telephone lines.
To connect the machine to a telephone line, use a snap-in modular type connector.
Important
❒Make sure the connector is the correct type before you start.
1.External telephone connector
2.G3 (analog) line interface connector
3.Extra G3 line interface connector
Selecting the Line Type
This section describes how to select the line type.
Select the line type to which the machine is connected. There are two types: tone
and pulse dial.
Select the line type using Administrator Tools.
Note
❒This function is not available in some regions.
Reference
p.108 “Select Dial / Push Phone”
ARM003S
Downloaded From ManualsPrinter.com Manuals 
						

							39
2. System Settings
This chapter describes user tools in the System Settings menu. For details on
how to access System Settings, see Accessing User tools (System Settings).
General Features
This section describes the user tools in the General Features menu under System
Settings.
Default settings are shown in bold type.
❖Panel Tone
The beeper (key tone) sounds when a key is pressed.
The default setting is On.
❖Warm Up Notice (copier/Document Server)
You can have the beeper sound when the machine becomes ready to copy af-
ter leaving Energy Saver mode, or when the power is turned on.
The default setting is On.
❖Copy Count Display (copier/Document Server)
The copy counter can be set to show the number of copies made (count up) or
the number of copies yet to be made (count down).
The default setting is Up (count up).
❖Function Priority
Specify the mode to be displayed immediately after the operation switch is
turned on, or when System Reset mode is turned on.
The default setting is Copier.
❖Print Priority
Print Priority is given to the mode selected.
When [Interleave] is selected, the current print job will be interrupted after a
maximum of five sheets.
The default setting is Display Mode.
When [Interleave] is selected, the current print job will be interrupted after a
maximum of five sheets.
When the Internal Tray 2 (1 bin tray), Shift Sort Tray, 500–sheet finisher, or
1000–sheet finisher is installed on the machine, you can specify an output tray
for each documents are delivered. For details about how to specify an output
tray for each function, see Output: coier, Output: Document Server, Out-
put: Facsimile, Output: Printer.
Downloaded From ManualsPrinter.com Manuals 
						

							System Settings
40
2
❖Function Reset Timer
You can set the length of time the machine waits before changing modes
when using the multi-access function.
This is useful if you are making many copies and have to change settings for
each copy. If you set a longer reset period, you can prevent interruption from
other functions.
The Function Reset Timer setting is ignored if [Interleave] is set for Print Priority.
The default setting is Set Time.
When you select [Set Time], enter the time (3–30 seconds, in 1 second incre-
ments) using the number keys.
The default setting for Set Time is 3 seconds.
❖Output: Copier (copier)
Specify a tray to which documents are delivered.
1. Internal Tray 1
2. Internal Tray 2
3. Finisher Upper Tray
4. Finisher Shift Tray
The default setting is Internal Tray 1.
❖Output: Document Server (Document Server)
Specify a tray to which documents are delivered.
The default setting is Internal Tray 1.
❖Output: Facsimile (facsimile)
Specify a tray to which documents are delivered.
The default setting is Internal Tray 1.
❖Output: Printer (printer)
Specify a tray to which documents are delivered.
The default setting is Internal Tray 1.
The output trays set on the printer driver have priority over the output tray
specified above.
AHR009S
Downloaded From ManualsPrinter.com Manuals 
						

							General Features
41
2
❖Size Setting
Currently three types of F size are available; 81/2×13L, 81/4×13L and
8×13L. The ADF or exposure glass cover sensor cannot distinguish these
three types of originals. This function sets the F size from the ADF or expo-
sure glass cover sensor. Auto Paper Select or Auto Reduce/Enlarge can be
used for F size originals based on this setting.
The default setting is 8
1/2×13L.
Reference
p.3 “Accessing User Tools”
Function Compatibility, Copy/Document Server Reference
Output tray settings
Important
❒You cannot interrupt the current job with a different function job that speci-
fies stapling or sorting.
❒You can interrupt the current job with an ordinary copy job or facsimile re-
ception. The output tray used when the job is interrupted varies depending
on the type of finisher shift tray and output tray specified for interruption.
❖When 500–sheet finisher is the finisher shift tray:
 When the output tray specified for the interrupting job is the finisher tray,
the interrupting job will be delivered to internal tray 1.
 When the output tray specified for the interrupting job is not the finisher
tray, the interrupting job will be delivered to the specified output tray.
❖When 1000–sheet finisher is the finisher shift tray:
 When the output tray specified for the interrupting job is the finisher tray,
the interrupting job will be delivered to the finisher upper tray.
 When the output tray specified for the interrupting job is not the finisher
tray, the interrupting job will be delivered to the specified output tray.
When the 500–sheet finisher or 1000–sheet finisher is installed and stapling is
specified for a job, the job will be delivered to the finisher shift tray, regardless
of the output tray specified.
Downloaded From ManualsPrinter.com Manuals 
						

							System Settings
42
2Tray Paper Settings
This section describes the user tools in the Tray Paper Settings menu under Sys-
tem Settings.
Default settings are shown in bold type.
Important
❒If the specified paper size differs from the actual size of the paper loaded in
the paper tray, a misfeed might occur because the correct paper size was not
detected.
❖Paper Tray Priority: Copier (copier/Document Server)
Specify the tray to supply paper for output.
The default setting is Tray 1.
❖Paper Tray Priority: Facsimile (facsimile)
Specify the tray to supply paper for output.
The default setting is Tray 1.
❖Paper Tray Priority: Printer (printer)
Specify the tray to supply paper for output.
The default setting is Tray 1.
❖Tray Paper Size: Tray 1-4
Select the size of the paper loaded in the paper tray.
 The paper sizes you can set for tray 1, 3 and 4 are as follows:
A3L, B4 JISL, A4K, A4L, B5 JISK, B5 JISL, A5L, 8KL, 16KK, 16KL
11×17L, 8
1/2×14L, 81/2×11K, 81/2×11L, 51/2×81/2L,
71/4×101/2L, 8×13L, 81/2×13L, 81/4×13L, 11×14L,
81/4×14L, 8×101/2L, 8×101/2K, custom size (140-297 mm 
(5.52-11.69) wide x 182-432 mm (7.17-17.00) long)
 The paper sizes you can set for tray 2 are as follows:
A3L, B4 JISL, A4K, A4L, B5 JISK, B5 JISL, A5L, B6 JISL, A6L, 
PostcardL, 8KL, 16KK, 16KL
11×17L, 8
1/2×14L, 81/2×11K, 81/2×11L, 51/2×81/2L,
71/4×101/2L, 71/4×101/2K, 8×13L, 81/2×13L, 81/4×13L,
11×14L, 11×15L, 10×14L, 10×15L, 81/4×14L, 8×101/2L,
8×101/2K, 8×10L, 8×10K, C5 EnvL, C6 EnvL, DL EnvL,
37/8×71/2L, 41/8×91/2L, custom size (100-297 mm (3.97-11.69) 
wide x 148-432 mm (5.83-17.00) long)
The default setting for Tray 1 is A4K / 8
1
2 × 11K.
The default setting for Tray 2 is A3L / 11 × 17L.
The default setting for Tray 3 is B5 JISK / 8
1/2 × 11L.
The default setting for Tray 4 is B4 JISL / 81/2 × 14L.
Downloaded From ManualsPrinter.com Manuals