Ricoh Aficio MP2510SP User Manual

73
3. Copier / Document Server
Features
This chapter describes user tools in the Copier / Document Server Features
menu. For details on how to access Copier / Document Server Features, see Ac-
cessing User Tools (System Settings).
General Features
This section describes the user tools in the General Features menu under Copier /
Document Server Features.
Default settings are shown in bold type.
❖Auto Paper Select Priority
Auto Paper Select is the default setting. You can cancel this setting.
The default...

Copier / Document Server Features
74
3
❖Original Type Priority
You can select the original type effective when the power is turned on, or
modes cleared.
The default setting is Text.
❖Original Type Display
You can have the original types shown on the initial display.
The default setting is Display.
If you select [Hide], the display is as below.
❖Auto Image Density Priority
You can set whether Auto Image Density is On or Off when the machine
is turned on, reset, or modes are cleared.
The default setting...

General Features
75
3
Pale
Adjust the quality level for the finish of a pale original with normal density.
The default setting is Normal.
Custom Setting is the value set during service setup.
 Generation Copy
Adjust the quality level so as not to thicken the lines of the finish image.
The default setting is Normal.
Custom Setting is the value set during service setup.
❖Image Density
You can select one of seven original image density levels for each original
type (Text, Text/Photo, Photo, Pale,...

Copier / Document Server Features
76
3
❖Job End Call
You can choose whether or not the beeper sounds when copying is complete.
The default setting is On.
If Panel Tone of User Tools (System Settings) settings is [On], the machine
beeps to notify you that it did not complete a job for reasons such as copying
was interrupted, the paper tray ran out of paper, or a paper jam occurred.
❖Copy Function Key: F1-F5
You can assign frequently used functions to function keys F1 to F5.
The default setting for Copy...

Reproduction Ratio
77
3 Reproduction Ratio
This section describes the user tools in the Reproduction Ratio menu under Cop-
ier / Document Server Features.
Default settings are shown in bold type.
❖Shortcut R / E
You can register up to three frequently used Reduce/Enlarge ratios other
than the fixed Reduce/Enlarge ratio and have them shown on the initial dis-
play. You can also change registered Reduce/Enlarge ratios.
If no Reduce/Enlarge ratio has been set when selecting [Shortcut R / E 1], [Short-
cut R...

Copier / Document Server Features
78
3
❖Reduce 1-6
You can customize available reduction ratios by pressing [Reduce / Enlarge],
followed by [Reduce].
The default setting for Reduce 1 is 25% (Metric version) / 25% (Inch version).
The default setting for Reduce 2 is 50% (Metric version) / 50% (Inch version).
The default setting for Reduce 3 is 65% (Metric version) / 65% (Inch version).
The default setting for Reduce 4 is 71% (Metric version) / 73% (Inch version).
The default setting for Reduce 5 is 75%...

Edit
79
3 Edit
This section describes the user tools in the Edit menu under Copier / Document
Server Features.
Default settings are shown in bold type.
Enter the width of the binding margin with the number keys as follows:
 Metric version: 0–30 mm (in increments of 1 mm)
 Inch version: 0-1.2 (in increments of 0.1 inch)
Enter the width of the erased margin with the number keys as follows:
 Metric version: 2–99 mm (in increments of 1 mm)
  Inch version: 0.1-3.9 (in increments of 0.1 inch)
An image of...

Copier / Document Server Features
80
3
❖Erase Border Width
Specify the width of erased border margins using this function.
The default setting is 10 mm (Metric version) / 0.4 (Inch version).
❖Erase Original Shadow in Combine
In Combine Copy or Booklet/Magazine Copy mode, you can specify whether
to erase a 3mm, 0.1 bounding margin around all four edges of each original.
The default setting is Yes.
❖Erase Centre Width
Specify the width of the erased centre margins with this function.
The default setting is...

Edit
81
3
❖Double Copies Separation Line
You can select a separation line using the Double Copies function from: None,
Solid, Broken A, Broken B, or Crop Marks.
None
 Solid
Broken A
Broken B
 Crop Marks
The default setting is None.
Selecting solid or broken lines might produce a blank area of approximately
1.5 mm (0.06) in width along the separation line.
Downloaded From ManualsPrinter.com Manuals 

Copier / Document Server Features
82
3
❖Separation Line in Combine
You can select a separation line using the Combine function from: None, Sol-
id, Broken A, Broken B, or Crop Marks.
None
 Solid
Broken A
Broken B
 Crop Marks
The default setting is None.
Selecting solid or broken lines might produce a blank area of approximately
1.5 mm (0.06) in width along the separation line.
❖Copy on Designating Paper
Specify whether to copy onto slip sheets.
The default setting is Yes.
❖Front Cover Copy in...