Ricoh Aficio MP2510SP User Manual

Tray Paper Settings
43
2
The paper guide for the optional LCT is fixed for A4K, 81/2×11K size pa-
per. Contact your service representative if you need to change the paper size.
If the paper size set for the selector in paper tray is different to the paper size
for this setting, the paper size of the dial has priority.
If you load paper of a size not indicated on the paper size selector in the paper
tray, set the dial to  .
❖Paper Type: Bypass Tray
Sets the display so you can see what type of paper is...

System Settings
44
2
❖Slip Sheet Tray
Allows you to specify and display the paper tray that is inserting slip sheets.
After selecting the paper tray, you can also specify the display timing and
copy method for two-sided copying.
The default setting for Tray to Program is Off.
When [At Mode Selected] is selected, slip sheet tray settings only appear when
the cover function or slip sheet function is selected.
❖Printer Bypass Paper Size
Specify the size of the paper in the bypass tray when printing data...

Timer Settings
45
2 Timer Settings
This section describes the user tools in the Timer Settings menu under System
Settings.
Default settings are shown in bold type.
❖Auto Off Timer
After a specified period has passed, following job completion, the machine
automatically turns off, in order to conserve energy. This function is called
Auto Off. The machine status after the Auto Off operation is referred to as
Off mode, or Sleep mode. For the Auto Off Timer, specify the time to
elapse before Auto Off.
The...

System Settings
46
2
❖Printer Auto Reset Timer (printer)
Specifies the time to elapse before the printer function resets.
If [Off] is selected, the machine does not automatically switch to the user code
entry screen.
The time can be set from 10 to 999 seconds, using the number keys.
The default setting is On, 60 seconds.
❖Scanner Auto Reset Timer (scanner)
Specifies the time to elapse before the scanner function resets.
If [Off] is selected, the machine will not automatically switch to the user code...

Interface Settings
47
2 Interface Settings
This section describes the user tools in the Interface Settings menu under System
Settings.
Default settings are shown in bold type.
Network
This section describes the user tools in the Network menu under Interface Set-
tings.
❖IP Address
Before using this machine in the network environment, you must specify the
IP address and subnet mask.
When you select [Specify], enter the IP Address and subnet mask as
xxx.xxx.xxx.xxx (x indicates a number).
The default...

System Settings
48
2
❖Effective Protocol
Select the protocol to use in the network.
The default setting for TCP/IP is Effective.
The default setting for NetWare is Effective.
The default setting for SMB is Effective.
The default setting for AppleTalk is Effective.
❖NCP Delivery Protocol
Select the protocol for NCP delivery.
The default setting is TCP / IP Priority.
❖NW Frame Type
Select the frame type when you use NetWare.
The default setting is Auto Select.
❖SMB Computer Name
Specify the SMB computer...

Interface Settings
49
2
❖Ping Command
Check the network connection with ping command using given IP address.
If you fail to connect to the network, check the following, and then retry the
ping command.
 Make sure that “TCP/IP” in [Effective Protocol] is set to “Effective”.
 Check that the machine with assigned IP address is connected to the net-
work.
 There is a possibility that the same IP address is used for the specified
equipment.
❖Permit SNMP V3 Communication
Set the encrypted communication of...

System Settings
50
2
Parallel Interface
This section describes the user tools in the Parallel Interface menu under Inter-
face Settings.
[Parallel Interface] is displayed when this machine is installed with the IEEE 1284
interface board.
❖Parallel Timing
Specify the timing for the parallel interface. Normally, you do not need to
change this setting.
The default setting is ACK Outside.
❖Parallel Communication Speed
Sets the communication speed for the parallel interface. If the speed is too
high, data may...

Interface Settings
51
2
IEEE 802.11b
This section describes the user tools in the IEEE 802.11b menu under Interface
Settings.
[IEEE 802.11b] is displayed when this machine is installed with the wireless LAN
interface board.
Be sure to make all settings simultaneously.
❖Communication Mode
Specifies the communication mode of the wireless LAN.
The default setting is 802.11 Ad hoc.
❖SSID Setting
Specifies SSID to distinguish the access point in infrastructure mode or 802.11
ad hoc mode.
The characters that...

System Settings
52
2
Print List
This section describes how to print the configuration page.
You can check items related to the network environment.
The configuration page shows the current network settings and network infor-
mation.
APress [System Settings].
BPress [Interface Settings].
CPress [Print List].
DPress the {Start} key.
The configuration page is printed.
EPress [Exit].
FPress the {User Tools/Counter} key.
Note
❒You can also exit by pressing [Exit] on the User Tools main menu.
Downloaded From...