Panasonic Wma Mp3 Cd Player Receiver Cq C8803u Operating Instructions

							CQ-C8803U
English
11
Although most of the functions of this unit are executable
with both the main unit and remote control, the following
functions are excluded.
Operations executable only with main unit
¡Face panel’s opening, closing, tilting, and removal
actions (apage 15)
¡Disc ejection (apage 15)
¡Dimmer (apage 17)
¡CS AUTO on, off, and adjustment (apage 18)
¡SQ on, off, and adjustment (apage 19)
¡Direct memory setting and calling (apage 23)
Operations executable only with remote control
¡Preset station calling with one-touch operation 
(apage 21)
¡Direct access to tracks on CDs (apage 25, 27)
¡Random and repeat play with one-touch operation 
(apage 25, 27)
¡Scan playback (apage 25, 27)
Controls Layout
Remote Control Unit Operations executable only with main unit/
operations executable only with remote control
SELSELSRCSRC
BANDBANDMUTEMUTE
23 1
5
8
06 4
9 7
#
VOLVOL
DISP
CAR AUDIO
MENU
SEL POWER
SOURCE
SRC
SET
BAND MUTE
23 1
5
8
06 4
9 7
#
VOL
RANDOM
NUMBER TUNE TUNESCAN REPEAT
DISP
POWER
SRC (SOURCE)
MUTE
SBC-SW Super Bass
Control-Subwoofer BAND
Pause/Play
SET
APM 
Auto Preset
Memory
SELSelect
MENUVOLVolume
}:Up
{:Down
DISPDisplay
0
4RANDOM
5SCAN
6REPEAT
7
9
#NUMBER
Number Buttons
–
Number
RANDOM0 to9
SCAN
REPEAT
9
TUNE
TRACK(FILE)
P·SET
(Preset)
DISC (FOLDER)
8
0 
						

							12
Preparation
CQ-C8803U
Cancellation of demonstration screen Remote Control Preparation
Preparation Before Initial Use
Pull the insulation film out
from the backside of
remote control gently.
Battery Replacement
qw
qRemove the battery holder
with the remote control unit
placed on a flat surface.
qStick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
wPull it out in the direction
of the arrow using a
tough pointed object.
2
3
wPut a battery in the case
with (+) side facing up.
ePut the case back.Tough pointed object
Back side
Insulation film
Warning
Keep batteries and insulation film out of reach of
infants. If an infant ingests a battery, please seek
immediate medical attention.
Cautions
¡Remove and dispose of an old battery immediately.
¡Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
¡Follow local regulations when disposing of a battery.
¡Improper use of a battery may cause overheating, an
explosion or ignition, resulting in injury or a fire.
Note:Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under normal use
(at room temperature)
For the first use, the following screen may appear
repeatedly.
1Set your car’s ignition switch to the ACC
or On position.
The demonstration screen appears.
2Press [SRC](PWR:Power).
3Press [MENU]to display the menu
display.
For using the remote control, hold down [SEL]
(MENU)for 2 sec. or more.
4Press []]or [[]to display the
DISPLAY menu.
5Press [{]or [}]to select
“DEMONSTRATION”.
6Press [BAND] (SET) to select “OFF”
7Press [MENU].
For using the remote control, hold down [SEL]
(MENU)for 2 sec. or more.
Note:This unit is operable as usual even if the
demonstration screen is activated. The demonstration
screen automatically appears if no operation is executed
for 1 minute. 
						

							CQ-C8803U
English
13
Note: Adjust the clock when “ADJUST” appears on the
display.
1Press [MENU]to display the menu
display.
For using the remote control, hold down [SEL]
(MENU)for 2 sec. or more.
2Press []]or [[]to display the
DISPLAY menu.
3Press [{]to select “CLOCK ADJ”.
4Press [BAND] (SET) to confirm the
display.
5Adjust the setting value.
[[]
:Adjusting minutes
[]]: Adjusting hours
[}]: Forward
[{]: Backward
6Press [BAND] (SET) to confirm the
adjustment.
7Press [MENU].
For using the remote control, hold down [SEL]
(MENU)for 2 sec. or more. You may need to set the following depending on the
devices to be connected.
Using Subwoofer
¡Subwoofer level adjustment (apage 31)
¡Subwoofer low pass filter (apage 31)
Connecting an AV device (TV, VTR)
If you connect TV to AUX1 terminal, set the AUX1 setting
to TV.
1Press [SRC](Source) to select the
AUX1 mode. 
(apage 16)
2Press [MENU]to display the menu display.
For using the remote control, hold down [MENU]
for 2 sec. or more.
3Press [BAND](SET)to adjust.
: For connection of other than a TV (default)
: For connection of a TV
4Press [MENU]to confirm the adjust-
ment.
Note: Other settings are required when a Sirius receiver,
an XM receiver, or a Hands-Free Phone System is
connected. (aSystem Upgrade Guidebook)
The following functions are activated when the Security
Function is ON. (a page 32)
¡The security indicator lights up when removing the
face plate.¡The alarm sounds and the message appears on the
screen to warn you to remove the face plate at ACC
off.
Security Indicator
Preparation
Security Function
Setting
Other Settings Clock adjustment 
						

							Power on
Press [SRC](PWR:Power).
Power off
Hold down [SRC](PWR:Power)until you
hear a beep, then release it.
14
General
This chapter explains how to turn on or off the power, how to adjust the volume, etc.
CQ-C8803U
You can remove the face plate to prevent it from being
stolen.
Removing
1Turn off the power (apage 14)
2Press [] (Release).
(The face plate disengages with a click when it is
removed.)
The face plate auto-
matically closes after a
lapse of 5 seconds
while it is open.
The power is automat-
ically turned off while
the unit is active.
3Put the face
plate in the case.
Mounting
1Slide the left side of the face plate in
place.
2Press the right end of the face plate
until “click” is heard.
Cautions:
¡It is recommended to remove or mount the face
plate when the plate is at the closed position.
Do not remove or mount the face plate when the
plate is in motion.
¡This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡Do not remove the face plate while driving your car.¡Do not place the face plate on the dashboard or
nearby areas where the temperature rises to high
levels.
¡Do not touch the contacts on the face plate or on the
main unit, since this may result in poor electrical
contacts.
¡If dirt or other foreign substances get on the con-
tacts, wipe them off with clean and dry cloth.
¡To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
Power On/off
(PWR: Power)
Face Plate Removing/Mounting
(Anti-Theft System) 
						

							CQ-C8803U
English
15
Open/Eject
Press [u] (OPEN).
When a disc is already loaded, the disc will automatically
be ejected.
Close
Press [u] (OPEN).
Tilt
The display angle changes among 4 levels as follows
every time you hold down [u] (TILT)for 1 sec. or
more and release. 
Note:The last selected
angle is memorized even
after turning off the power.
Notes:
¡The volume level can be set independently for each
source. (For radio, one volume setting for AM, one
volume setting for all FMs)
¡The volume is not adjustable while an error display is
on the monitor. (apage 39)
¡This unit memorizes individual volume levels for each
source. Make volume adjustments of each source
appropriately to prevent large volume fluctuation when
the source is changed.
qUp
wDown
Setting Range: 0 to 40
Default: 18
Volume off (down)
Press [MUTE].
Cancel
Press [MUTE]again.
Note: 
Volume-down range can be specified. 
(
apage 32)
General
Face Plate Motion (Open/Close, Tilt)
(OPEN/CLOSE, TILT)
Volume Adjustment
(VOLUME)
Temporary Volume Off (Down)
MUTE (ATT: Attenuation)
Cautions:
¡To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
¡Do not pinch your finger or hand in the face plate.
¡Do not insert foreign objects into the disc slots.
¡For the following cases, the face plate automatical-
ly closes. Use caution not to catch your finger.
¡After a lapse of 20 seconds
¡When a disc is inserted
¡When the face plate is removed (apage 14)
¡When ACC is set to off
TILT 1
TILT 2
TILT 3
OPEN
TILT OFF 
						

							16
General
CQ-C8803U
Radio
FM1, FM2, FM3, AM (apage 21)
Source Selection
(SOURCE)
The source changes as follows every time
[SRC: Source]is pressed.
Player
When loading CD (apage 24)
When loading MP3/WMA disc (apage 26)
AUX 1
Device connected to the AUX terminal of the this unit 
System-up Connector
Device connected to the System-up Connector of the
this unit
When optional devices are connected:
Shift to connected devices
When an expansion module is connected:
The devices connected to the ports 1 to 4 are activated
in sequence after shifting to AUX2 (devices connected
to the AUX terminal of the expansion module).
Note:For information about connectable devices, refer
to the System Upgrade Guidebookor the instruction
manual for each device.
When connecting DVD Changer
When connecting CD Changer 
When connecting iPod Player 
When connecting XM Receiver 
When connecting Sirius Receiver
When connecting Expansion Module
When connecting a TV (apage 13)
When connecting other than a TV 
						

							CQ-C8803U
General
English
17
The display changes as follows every time [D] (DISP:
DISPLAY) is pressed.
Note:The graphic pattern and still image are selectable.
(apage 33)
At power-off:
Clock display (default) Mode
Folder hierarchy (MP3/WMA mode only.)
Ordinary display + graphic pattern
Ordinary display + still imageOrdinary display + clock
Display OFF
All displays disappear in 5 seconds.
At power-on:
Off
Only still image
Display Change
(DISP: Display)
The dimmer level changes as follows every time you hold
down [MENU] (DIM: Dimmer)for 2 sec. or more.
Dimmer Control
(DIM: Dimmer)
Note:This setting is not adjustable with the remote
control.
Brighter (default)
Medium
Darker Only graphic pattern 
						

							18
Sound Control
This unit is equipped with CS AUTO technology as well as conventional tone adjustment. Select your favorite sound world.
CQ-C8803U
CS AUTO Setting(CS AUTO Menu Display)
CS AUTO allows your car interior to change to a splendid
audio room in a moment. Every speaker can be fine-
tuned.
You can toggle the CS Auto function on and off every
time you hold down [VOLUME](SRS CS) for 2 sec or
more.
Note:If you enable CS AUTO, the following functions
are automatically disabled:
SQ, POSITION, BASS/TREBLE, BALANCE/FADER, SUB-
WOOFER LEVEL, LPF, HPF, SBC-SW
You can make a fine adjustment to CS AUTO.
1Set the CS AUTO mode to on.
2Hold down [SQ]for 2 sec. or more to
display the audio menu display.
3Press [}]or [{]to select a function to
be adjusted.
4Press [BAND](SET) to adjust.
5Press [D] (DISP:DISPLAY)to confirm
the adjustment.
CS AUTO MODE
Three-dimensional natural sound field is reproduced with
clarity in response to sound.
: Music 
(default in other than the AM mode)
: Cinema
: Monaural (default in the AM mode)
Lights when CS AUTO is activated.
At CS Auto ON
Available items
¡Mode selectable from among MUSIC/CINEMA/
MONO (apage 18)
Adjustable items in audio setting(apage 30)
FRONT-TruBass, REAR-TruBass, SUB.W-TruBass, 
FRONT-FOCUS, REAR-FOCUS, F-R MIX
At CS Auto OFF
The following items are available only at CS AUTO off.
Available items
¡SQ (mode selectable from among
FLAT/ROCK/POP/VOCAL/JAZZ/CLUB) (apage 19)
¡SQ advanced setting/POSITION (apage 19)
¡SBC-SW (apage 20)
Adjustable items in audio setting(apage 31)
Bass, Treble, Balance, Fader, Subwoofer level adjustment,
Subwoofer Low Pass Filter, High Pass FilterSound control CS Auto 
(Circle Surround 
Automotive 
)
is a trademark of SRS Labs, Inc.
CS Auto technology is incorporated under license
from SRS Labs, Inc. 
						

							CQ-C8803U19
English
Sound Control
The equalizer curve is selectable from among preset 6
types (FLAT, ROCK, POP, VOCAL, JAZZ, and CLUB)
depending on your listening category.
Note:SQ is not changeable when CS AUTO is enabled.
(apage 18)
SQ changeover
The SQ category is changed every time [SQ](Sound
Quality) is pressed.
Note:Setting of SQ, bass/treble and volume are
influenced one another. If the influence mentioned above
causes distortion to the audio signal, readjust bass/treble
or volume. (apage 31)Lights when activated.
SQ is adjustable in accordance with your taste.
1Hold down [SQ]
(Sound Quality) for 2
sec. or more when CS
AUTO is disabled.
2Press [}]or [{]to select a function to
be adjusted.
3Press [BAND]
(SET) to adjust.
4Adjust the setting value.
5Press [DISP]to confirm the adjustment.
SQ ADJUSTMENT (SQ9)
(Band: 62.5, 125, 250, 500, 1 k, 2 k, 4 k, 8 k, and 16 kHz
(default), Setting range: –12 dB to 12 dB, in 2 dB steps)
You can make a fine adjustment to the currently selected
SQ presetting in each type.
[]][[]:Frequency band selection
qw:Frequency selection
[
}][{]:Level up/down
Note:If you hold down [BAND]for 2 sec. or more, the
presetting that is called up can be turned into the default.
POSITION
You can make the optimal sound field in accordance with
your seat.
[]][[]:Selection
(): Disabled (default)
(): Right side of front seat
(): Left side of front seat
(): Both sides of front seat
(): Both sides of rear seat
SQ Selection Based on Genre
(SQ: Sound Quality)
SQ adjustment
(USER) 
						

							20CQ-C8803U
Sound Control
The rear speaker can be used as a substitutional
subwoofer when a subwoofer is not connected.
Holding down [MUTE](SBC-SW)for 2 sec.
or more toggles SBC-SW on and off.
Lights when activated.
Off (default)
On
Notes:
¡If ON is selected, the settings of subwoofer level
adjustment and subwoofer low pass filter are activat-
ed. (apage 31)
¡SBC-SW is not changeable when CS AUTO is enabled.
(apage 18)
Substitutional Subwoofer (SBC-SW: Super Bass Control·Subwoofer)