Panasonic Kx-tvs75, Kx-tvs100, Kx-tvs200 Voice Processing System Installation Manual

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
SYSTEM ADMINISTRATION
241
Ta b l e  7 3  
PBX TypeOther 
Manu-
facturersKX-T series
T308 T616T1232/
TA  
seriesT96 T336TD816/1232/
308TD500
Integration 
ModeNone
None NoneNone None None None
*D-
PITSNone*D-
PITS
Inband Inband Inband Inband Inband Inband
Operator 
Transfer 
SequenceFX FTX FTX FTX FTX FTX FTX FX FTX FX
Extension 
Transfer 
SequenceFX FTX FTX FTX FTX FTX FTX FX FTX FX
Alternate 
Extension 
Transfer 
SequenceFX FTX FTX FTX FTX FTX FTX FX FTX FX...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
242SYSTEM ADMINISTRATION
N/A: Not available 
—: Not needed
To program the following 10 Parameters on the following page, use the Special Commands 
and Dial Codes listed below. Up to 12 digits can be set for each parameter.
D: Disconnecting
F: Hook Flash
R: Ring Back Tone Detection
S: Silence Detection
T: Dial Tone Detection
W: Wait for 1 s
X: Extension dialing
A: Answer
1-9, 0,   , #: Dial CodesTable 74 
Parameter Value Range
(Default)Description/Function...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
SYSTEM ADMINISTRATION
243
Inband Signaling Parameters
These parameters are used if the PBX sends DTMF tones to the VPS to indicate the state of a 
call (busy, answered, disconnected, etc.). The integration Mode must be set to Inband. If PBX 
type is set to a KX-T series telephone system, the Inband Signaling Parameters will 
automatically default to the proper codes.Ta b l e  7 5  
Parameter Value Range
(Default)Description/Function
Operator 
Transfer...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
244SYSTEM ADMINISTRATION
The following parameters can be programmed using 0-9,  , #, and A-D.
Note
Default values in the above table vary depending on the settings of PBX type and
Inband Integration (PBX Interface Parameters)
. To select Inband Signaling Parameters, follow the menu path as shown:
System Administration Top Menu - 1 - 6 - 3 - 2
Ta b l e  7 6  
Parameter Value Range
(Default)Description/Function
Ringback
(1)Indicates Ringback Tone. Sent to the...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
SYSTEM ADMINISTRATION
245
N/A: Not available 
Digit Translation Table Parameters
The Digit Translation Table is used to translate the Follow On ID Signal from the PBX into the 
proper codes for the VPS. This translation table is only effective for the incoming signal.
Digit Translation Table Parameters - Inter-Digit Timeout
Table 77 
ParameterOther
ManufacturersKX-T series
T308 T616T1232/
TA seriesT96 T336TD816/
1232/308TD500
Ringback N/A N/A N/A 1 A1 A1 1 1...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
246SYSTEM ADMINISTRATION
Digit Translation Table Parameters - Input/Output
Table 78 
Parameter Value Range
(Default)Description/Function
Inter-digit 
Timeout1-4 sec
(1seconds)This parameter defines the incoming signal interval 
(Follow on ID). The Digit Translation Table is translated 
by a series of signals received within the specified time 
period.
To select Input/Output, follow the menu path as shown:
System Administration Top Menu - 1 - 6 - 3 - 3 - 2...

SYSTEM MANAGERS GUIDE247
Appendix C
SYSTEM MANAGERS GUIDE 

C1 ACCESSING THE SYSTEM MANAGERS MAILBOX
248SYSTEM MANAGERS GUIDE
C1 ACCESSING THE SYSTEM MANAGERS 
MAILBOX
Three items of information must be known before accessing the System Managers Mailbox— 
the telephone number connected directly to the Voice Mail Service, the System Managers 
Mailbox Number and the Password for that mailbox (if assigned). The System Managers 
Mailbox Number is 99, 999, 9999 or 99999 depending upon the mailbox number length 
specified in System Programming. The System Managers...

C2 SETTING UP MAILBOXES
SYSTEM MANAGERS GUIDE
249
C2 SETTING UP MAILBOXES
The System Managers primary function is to create mailboxes for new Subscribers and to 
maintain system organization by deleting unneeded passwords and mailboxes.
Creating and Editing a Mailbox
The System Manager is able to both create and edit Subscriber mailboxes. Mailboxes can be 
created or edited by following the steps below.
At any step, when editing an assigned mailboxs parameters, change current settings by 
Pressing [1]....

C2 SETTING UP MAILBOXES
250SYSTEM MANAGERS GUIDE
8.The All Calls Transfer to Mailbox parameter is the last parameter to be entered. When this 
entry is completed, the prompt at step 4 will appear. Continue assigning or editing other 
mailboxes by repeating steps 5-7.
9.To return to the Main Command Menu, 
Press [ ] twice.
Deleting a Mailbox
When mailboxes are no longer needed, they must be deleted. If the mailbox to be deleted is 
being used, the action is automatically cancelled and the message Sorry,...