Panasonic Kx-tvs75, Kx-tvs100, Kx-tvs200 Voice Processing System Installation Manual

B6 SYSTEM ADMINISTRATION - SYSTEM PARAMETER SETTINGS
SYSTEM ADMINISTRATION
231
Message 
Waiting Lamp 
PortsPort No.
(1, 2, 3, 4)Specifies the port numbers used for the Message Waiting 
Notification Lamp feature. 
The VPS turns on the Message Waiting Lamp of the 
extension using the port specified in this field. At least 1 
port must be specified.
Note: The value range depends upon the VPS model. 
TVS75: 1-2, TVS100: 1-4, TVS200: 1-12
Message 
Waiting Lamp 
for Every 
Message1. No
2. Yes
(No)When set to...

B6 SYSTEM ADMINISTRATION - SYSTEM PARAMETER SETTINGS
232SYSTEM ADMINISTRATION
Other Parameters - External Message Delivery Parameters
Used to control the handling of External Message Delivery calls.
To select the External Message Delivery Parameter, follow the menu path as shown:
System Administration Top Menu - 1 - 5 - 6 - 4
Table 64 
Parameter Value Range
(Default)Description/Function
Retry Times 0-9 times
(3)Specifies the number of times that an external message 
delivery call should be attempted when...

B6 SYSTEM ADMINISTRATION - SYSTEM PARAMETER SETTINGS
SYSTEM ADMINISTRATION
233
Other Parameters - Call Hold Parameters
To select Call Hold Parameters, follow the menu path as shown:
System Administration Top Menu - 1 - 5 - 6 - 5
Ta b l e  6 5  
Parameter Value Range
(Default)Description/Function
Call Hold 
Mode1. Disable
2. Enable
(Enable)If set to Enable, the VPS gives callers the option of 
either holding for a specific extension or selecting one of 
several Incomplete Call Handling service options....

B6 SYSTEM ADMINISTRATION - SYSTEM PARAMETER SETTINGS
234SYSTEM ADMINISTRATION
Other Parameters - Rotary Telephone Service
This parameter defines how callers are treated who are calling from rotary telephones (unable 
to input DTMF signals) or who are unable to properly respond to VPS guidance.
Other Parameters - Intercom Paging Parameters
Intercom Paging is a PBX feature that makes it possible to page the callers party through 
telephone speakers. To utilize this feature, the PBX must have the Intercom...

B6 SYSTEM ADMINISTRATION - SYSTEM PARAMETER SETTINGS
SYSTEM ADMINISTRATION
235
Other Parameters - Fax Management
The VPS can be programmed to automatically transfer incoming fax calls to a fax extension. 
A maximum of 2 fax extensions can be specified as the destination for the Automatic Fax 
Transfer. If the main fax extension is not available to receive a fax, the VPS will transfer the 
fax transmission to the alternate fax extension. Release for 
Intercom 
PagingUp to 12 digits con-
sisting of 0-9, ,...

B6 SYSTEM ADMINISTRATION - SYSTEM PARAMETER SETTINGS
236SYSTEM ADMINISTRATION
Table 68 
Parameter Value Range
(Default)Description/Function
Automatic 
Transfer of 
Incoming Fax 
Call1: Disable
2: Enable
(Disable)Used to enable or disable the Automatic Transfer of 
Incoming Fax Call Service.
Note: Auto detection works for only the first 30 s.
Main Fax 
Extension No.2-5 digits
(None)Specifies the main fax extension number.
Alternate Fax 
Extension No.2-5 digits
(None)Specifies the backup fax extension...

B6 SYSTEM ADMINISTRATION - SYSTEM PARAMETER SETTINGS
SYSTEM ADMINISTRATION
237
Other Parameters - Disconnect Parameter
Fax Notification 
Mode1. No
2. Mbx
3. Ext
(No)If set to Mbx, the VPS will leave the number of 
successfully received fax calls in the Fax Managers 
mailbox.
Example: 
You have 1 FAX message.
1) If set to Ext, after a fax extension successfully 
receives a fax call, the VPS will automatically call the 
Fax Managers extension and play a voice prompt - 

You have 1 FAXmessage. The VPS will...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
238SYSTEM ADMINISTRATION
B7 SYSTEM ADMINISTRATION - HARDWARE 
SETTINGS
For System Administration (system setup, mailbox setup, and system diagnosis) an RS-232C 
terminal must be connected to the serial interface of the VPS.
B7.1 RS-232C Parameters
System Administration Top Menu - 1 - 6
To the RS-232C Parameter, follow the menu path as shown:
System Administration Top Menu - 1 - 6 - 1 
Ta b l e  7 0  
Parameter Value Range
(Default)Description/Function
Baud...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
SYSTEM ADMINISTRATION
239
B7.2 Port Setting
Port Setting Menu
Note
The port assignment procedure for other ports (TVS75:2, TVS100: 2- 4, 
TVS200: 2-12) is the same as Port 1. To select Port Setting, follow the menu path as shown:
System Administration Top Menu - 1 - 6 - 2 
To select the Port Setting Menu for Port 1, follow the menu path as shown:
System Administration Top Menu - 1 - 6 - 2 - 1
Ta b l e  7 1  
Parameter Value Range
(Default)Description/Function...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
240SYSTEM ADMINISTRATION
B7.3 PBX Interface Parameters
Three separate parameters are used to program the VPS for optimal signaling and performance 
with the PBX.
Dialing Parameters
These parameters specify how the VPS will initiate and control call transfers, setup outgoing 
calls, and control message waiting lamps on extensions. The procedure for verifying the correct 
code sequences for non-Panasonic KX-T series telephone systems is to manually execute the...