Panasonic Kx-tvs50, Kx-tvs80 Voice Processing System Installation Manual

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
SYSTEM ADMINISTRATORS GUIDE
251
To program the following 10 Parameters on the following page, use the Special Commands and 
Dial Codes listed below. Up to 12 digits can be set for each parameter.
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
S: Silence Detection
T: Dial Tone Detection
W: Wait for 1 s
X: Extension dialing
A: Answer
1-9, 0,   , #: Dial Codes
Ta b l e  6 8  
Parameter Value Range
(Default)Description/Function
Operator 
Transfer...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
252SYSTEM ADMINISTRATORS GUIDE
Inband Signaling Parameters
These parameters are used if the PBX sends DTMF tones to the VPS to indicate the state of a 
call (busy, answered, disconnected, etc.). The integration Mode must be set to Inband. If PBX 
type is set to a KX-T series telephone system, the Inband Signaling parameters will 
automatically default to the proper codes.
The following parameters can be programmed using 0-9,  , #, and A-D.Call Waiting...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
SYSTEM ADMINISTRATORS GUIDE
253
Note
Default values in the above table vary depending on the settings of PBX type and Inband 
Integration (PBX Interface Parameters).Forward to VM 
Busy (7)Sent to the VPS if the called extension is forwarded to a 
voice mail port and that voice mail port is not available to 
accept the call.
Forward to 
Other 
Extension(8)Sent to the VPS if the called extension is forwarded to 
another, non-voice mail extension.
Confirmation...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
254SYSTEM ADMINISTRATORS GUIDE
The Digit Translation Table is used to translate the Follow On ID Signal from the PBX into the 
proper codes for the VPS. This translation table is only effective for the incoming signal. Digit Translation Table Parameters
To select the Digit Translation Table Parameters, follow the menu path as shown:
System Administration Top Menu - 1 - 6 - 3 - 3
Digit Translation Table Parameters - Inter-Digit Timeout
To select Inter - Digit...

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
SYSTEM ADMINISTRATORS GUIDE
255
Ta b l e  7 2  
Parameter Value Range
(Default)Description/Function
Ta b l e
1-8Input digit Up to 8
digits
consisting of
0-9, , #,
A-D
(None)Do not assign more than 1 code to an incoming 
signal. If this occurs, the system will take the first 
assignment.
Output 
digit 

B7 SYSTEM ADMINISTRATION - HARDWARE SETTINGS
256SYSTEM ADMINISTRATORS GUIDE 

SYSTEM MANAGERS GUIDE257
Appendix C
SYSTEM MANAGERS GUIDE 

C1 ACCESSING THE SYSTEM MANAGERS MAILBOX
258SYSTEM MANAGERS GUIDE
C1 ACCESSING THE SYSTEM MANAGERS 
MAILBOX
The System Managers Mailbox must be accessed before any System Manager task can be 
performed. Three items of information must be known before accessing the System Managers 
Mailbox — the telephone number connected directly to the Voice Mail Service, the System 
Managers Mailbox Number and the Password for that mailbox (if assigned). The System 
Managers Mailbox Number is 99, 999, 9999 or 99999...

C2 SETTING UP MAILBOXES
SYSTEM MANAGERS GUIDE
259
C2 SETTING UP MAILBOXES
The System Managers primary function is to create mailboxes for new Subscribers and to 
maintain system organization by deleting unneeded passwords and mailboxes.
Note
While the System Administrator programs via a computer, the System Manager cannot set 
up mailboxes and Sorry, this function is not available.  is played.
Creating and Editing a Mailbox
The System Manager is able to both create and edit Subscriber mailboxes....

C2 SETTING UP MAILBOXES
260SYSTEM MANAGERS GUIDE
6.Press [2] to accept the entry.
7.As each parameter is played:
a)Press [1] to enter the new parameter or 
[2] to leave the parameter unchanged.
b)Enter the parameter and 
Press [1].
c)Confirm the new parameter is correct and 
Press [2] to accept it.
8.The All Calls Transfer to Mailbox parameter is the last parameter to be entered. When this 
entry is completed, the prompt at Step 4 will appear. Continue assigning or editing other 
mailboxes by repeating...