Panasonic Kx Tda50 Tda100 Tda200 Tda600 Operating Manual

Table 1 (Standard mode)Document Version  2010-11  Operating Manual511.3.14 Character Entry  

Table 2 (Option mode)
 To enter "Ann"
Note
•To erase the character on the cursor, press CLEAR.
• To move the cursor to the left, press 
.
• To move the cursor to the right, press 
. When entering two or more characters that use the same
button consecutively (e.g.  "G" and  "I"), you must press this button or the FWD/DND button after entering
the first character.
• If the SELECT button is pressed, the characters for each button will be displayed in reverse order.
• To toggle...

1.3.15  Conference–Conference
– Leaving Three-party Conference
 Conference
You can add one or more parties to your conversation.
To establish a conference call
Document Version  2010-11  Operating Manual531.3.15 Conference Press CONF. Dial desired 
phone number.
Seize CO line before 
dialing outside phone number.
PT/PS
Talk with 
multiple parties.
During a conversation
desired 
phone no.
Talk to the 
new party.CONF
Press CONF
or TRANSFER.
OR
CONF
TRANSFERC.ToneC.Tone Dial desired
phone number.
desired...

To establish a conference call when receiving a call from an outside party during a two-party
conversation
54Operating ManualDocument Version  2010-11  1.3.15 ConferenceDial desired
phone number.
desired 
phone no.
SLT
Talk with multiple parties.
Enter 3. Press Recall/
hookswitch.Talk to the 
new party.
3
During a conversation
Seize CO line before 
dialing outside phone number.
Press Recall/
hookswitch.
C.Tone PT/PS
Press HOLD.
During a conversation
HOLD
Press flashing CO,
PDN, or SDN.Talk to the
new...

To add four or more parties to a conference
To add another party on hold to a conference
To talk to two parties alternately in a three-party conversation
Document Version  2010-11  Operating Manual551.3.15 ConferencePress CONF. Press CONF. Dial desired 
phone number.
desired 
phone no.
Seize CO line before 
dialing outside phone number.
PT/PS
Talk.
During a conversation
Talk.
To continue
CONFCONF
C.Tone PT/PS
During a 3- to 7-party conference
Press flashing CO, ICD Group,
PDN, or SDN corresponding to
the...

To disconnect one party and then talk to the other in a three-party conversation
•* In this case, the FLASH/RECALL button on a proprietary telephone must be set to
Flash/Recall mode through system programming.
• During a three-party conversation, pressing the TRANSFER button or Recall/
hookswitch alternates between the two other parties in the conversation.
• You can have a conference with a maximum of eight parties (comprising intercom or
CO lines) simultaneously.
• During a conversation involving four...

To leave a conference involving at least one other extension
To leave a conference involving two outside parties
•To leave a conference call involving two outside parties and have the conversation continue,
your extension must be enabled to transfer calls to CO lines through COS programming.
1.3.16  Conference, Unattended
The person who originated a conference can leave the conference, and allow the other parties
to continue the conversation.Document Version  2010-11  Operating Manual571.3.16 Conference,...

To leave a conference
To return while others are talking
To complete a conversation
•Time limit
Both parties will hear an alarm tone before a specified timeout. The originating extension user
will hear an alarm tone before timeout. The call is disconnected when the timer runs out
unless the originating extension returns to the conference.Customizing Your Phone
• 3.1.4  Customizing the Buttons
Create or edit a Conference button.
1.3.17  Conference Group Call (KX-TDA50 only)
You can call multiple parties,...

To make/answer a conference group call•A caller using an SLT can originate a conference group call but cannot perform additional
operations, such as making a conversation with a specific party or ending a conversation with
a specific party.
• With some PS models, the call is not automatically answered. In this case, go off-hook to
answer a conference group call.
 For a caller
To make a conversation with a specific party
Document Version  2010-11  Operating Manual591.3.17 Conference Group Call (KX-TDA50...

To make a conversation with a party in the group’s preassigned order
To end a conversation with a specific party
•In this case, the FLASH/RECALL button must be set to Flash/Recall mode through system
programming.60Operating ManualDocument Version  2010-11  1.3.17 Conference Group Call (KX-TDA50 only)PT/PS
Press CONF.
During an announcement
CONF PT/PS
   To end a conversation with a specific party
During a conversation
(DSS)
Press DSS.
   To end a conversation with the party who 
   joined the...