Panasonic Kx-Td816c, Kx-td1232c Digital Super Hybrid System User Manual

User Programming
User Manual71
Using the Overlay
A programming overlay is packed with the telephone at the factory. This overlay should be 
used at all times in the programming mode since the functions of the telephone keys change 
during programming.
Location of Controls with the Overlay
The pictures below show the functions of the buttons of the KX-T7433, KX-T7436, KX-T7230 
and KX-T7235 in the programming mode. KX-T7431 is the same as KX-T7433 except for the 
Soft and SHIFT buttons. 

User Programming
72User Manual
SECRETPAUSEPROGRAM CLEAR
STORE
FLASH SELECT
END PREV NEXT
ABC DEF
JKL MNO GHI
TUV WXYZ
OPER PQRS
SHIFT Soft-1 Soft-2 Soft-3
SECRETPAUSEPROGRAM CLEAR
STORE
FLASH SELECT
END PREV NEXT
ABC DEF
JKL MNO GHI
TUV WXYZ
OPER PQRS
SHIFT Soft-1 Soft-2 Soft-3
PROGRAM
VOLUME
SHIFT
1
4
GHI
7PRS
5JKL
8TUV
0OPER
2ABC
6MNO
9WXY
3DEF
FLASH PREV END
STORE
SELECT
NEXT
SECRETPAUSE CLEAR
Soft-1 Soft-2 Soft-3
SECRETPAUSE CLEAR
PROGRAM
Soft 1 Soft 2 Soft 3
SHIFT
VOLUME1
4
GHI
7PRS
5JKL
8TUV
0OPER...

User Programming
User Manual73
Before entering the user programming mode
Before entering the user programming mode, confirm that:
Your telephone is on-hook, and
No calls are on hold at your telephone.
Entering the user programming mode
To enter the User Programming mode:
The display shows the Initial Message: USR-PGM NO? 
Note
If nothing is entered within five seconds after the PROGRAM button is pressed, 
programming mode is canceled.
During the programming mode, your extension is treated as a busy...

User Programming
74User Manual
3.1.2 Programming Methods
Advancing to the next stage
When USR-PGM NO?  is displayed, you can select one of the following:
To go to program [000], press the NEXT button.
To go to another program, enter the 3-digit program address.
Rotation of jack number
Each jack of the Digital Super Hybrid System supports the connection of a digital proprietary 
telephone and a single line device with different extension numbers (eXtra Device Port: XDP 
function). To program this...

User Programming
User Manual75
Making another selection within the same program address
To go to the next selection, press NEXT.
To go to the previous selection, press PREV.
To make a specific selection, press SELECT and then enter the number.
Accessing another program address
After pressing STORE, you can access another program by one of the following two methods:
a)To go to the next program address:
Larger program address

Press Soft 1 (SKP+) or VOLUME (DOWN).

Rotate the Jog Dial...

User Programming
76User Manual
3.2 User Programming
3.2.1 [000] Date and Time Set
Notice
It is assumed that you have read Section 3.1 User Programming Instructions. Soft button 
usage is explained in that section, therefore no references will be made to them in the following 
instructions. The soft buttons can be used in place of the overlay keys at any time.
Description
Sets the current date and time.
Selection
Ye a r :  00 through 99 
Month: Jan. through Dec.
Day: 1 through 31
Day of the week: SUN...

User Programming
User Manual77
Programming
Display PT
Dial 000. Enter the year
(last 2 digits).
000year


Press NEXT.
NEXT
Press →.
Keep pressing SELECT until
the desired month is displayed.
SELECT
Keep pressing SELECT until
the desired day of the week is
displayed.
SELECT
Press STORE.
STORE
Press NEXT.
NEXT
Enter the hour
(00 through 12).
hour
Press →.
Press END.
END
Press STORE.
STORE
Press SELECT for
AM or PM.
SELECT
Enter the minute
(00 through 59).
minute
Press →.Press SELECT for
12 or 24 (hour...

User Programming
78User Manual
Conditions
After changing an entry, you can press STORE. You do not have to perform the rest of the 
steps.
To return to the previous field, press   in steps 4 through 9 and steps 13 through 18.
If you hear an alarm after pressing STORE, check that the date is valid.
The clock starts immediately after the STORE button is pressed.
You cannot leave an entry empty.
Features Guide References
Display, in Idle  

User Programming
User Manual79
3.2.2 [001] System Speed Dialing Number Set
Description
Used to program the System Speed Dialing numbers. These numbers are available for any 
extension user in the system.
Selection
Speed dial numbers: 000 through 499 
Telephone number: 24 digits (max.) 
Default
All speed dial numbers — Not Stored 

User Programming
80User Manual
Programming
Conditions
Each speed dial number has a maximum of 24 digits. The valid characters are 0 through 9, 
, and # keys, and the FLASH, PAUSE, SECRET and
–(hyphen) buttons.
— To store the flash signal, press FLASH.
Note
: The Stored flash will only be effective during an established call.
— To store a hyphen, press the – button.
Display PT
Dial 001. Enter a speed dial number
(000 through 499).
speed dial no.

Press NEXT.
NEXT
 
SPD Code?→
To enter speed dial number...