Home
>
Panasonic
>
Communications System
>
Panasonic Kx-Td816c, Kx-td1232c Digital Super Hybrid System User Manual
Panasonic Kx-Td816c, Kx-td1232c Digital Super Hybrid System User Manual
Here you can view all the pages of manual Panasonic Kx-Td816c, Kx-td1232c Digital Super Hybrid System User Manual. The Panasonic manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 41
DPT Overview User Manual41 To adjust the ringer volume VOLUME 7230 / 7235 Ringer:*** (-volume level 3) While the telephone is ringing; Press VOLUME (UP /DOWN ) Control button. VOLUME S 1 S 2 S 3 RING 7230 / 7235 Press RING (S2). Press VOLUME (UP /DOWN ) Control button. The telephone will stop ringing in about 4 seconds. When the volume level is 0 (no * indication), the display shows RNGOFF. While the telephone is idle and on-hook; The telephone will ring. OFF HIGH LOW 7220 / 7250...
Page 42
DPT Overview 42User Manual To adjust the speaker volume SP-PHONE VOLUMEMONITOR 72XX Press SP-PHONE or MONITOR. SP:************ (-volume level 12) You may also adjust the speaker volume while listening to background music (BGM On mode), receiving a voice call, receiving a page or hearing a call progress tone such as a dial tone. Press VOLUME (UP /DOWN ) Control button.
Page 43
DPT Overview User Manual43 1.1.7 LED Indication The Light Emitting Diode (LED) buttons indicate the line conditions with lighting patterns. Flashing light patterns LED Indication on the INTERCOM Button The table below shows the lighting patterns for intercom line conditions. LED Indication on the CO Button The table below shows the lighting patterns for CO line conditions. — Items marked with * are only available on the Single-CO button.INTERCOM button Intercom Line Condition Off Green On Green slow...
Page 44
DPT Overview 44User Manual BLF on DSS Button The Busy Lamp Field (BLF) indicator button is red when the corresponding extension is busy. This is available for Direct Station Selection (DSS) buttons on DSS consoles and for flexible CO buttons assigned as DSS buttons on proprietary telephones. LED Indication on the FWD/DND Button The table below shows the lighting patterns for the FWD/DND Button. Programming Guide Reference [990] System Additional InformationSystem Programming [990] Area (09), Bit...
Page 45
Station Programming User Manual45 Section 2 Station Programming Note: All illustrations used in this section are based on model KX-T7235.
Page 46
Station Programming 46User Manual 2.1 Station Programming Instructions 2.1.1 Station Programming Instructions Station Programming allows you, the proprietary telephone (PT) users, to program certain features from your telephone individually. To program, you need to switch your telephone to the Station Programming mode. During programming mode, your telephone is in the busy condition to both inside and outside callers. If you want to make a normal call handling operation, you must finish the...
Page 47
Station Programming User Manual47 Exiting Station Programming mode PT Press PROGRAM or lift the handset. PROGRAM To exit the Station Programming mode, press PROGRAM. You are in the call handling mode. When the display shows the initial programming mode; or
Page 48
Station Programming 48User Manual Confirming the assigned function data — Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9]. — To exit the Station Programming mode: Press [PROGRAM] or lift the handset. — If you wish to change the data, follow the programming procedure explained in this section. PT Press HOLD (END). Enter the program access number. program access numberHOLD Enter the program access number* as follows. - 1:Preferred Line Assignment - Outgoing - 2:Preferred...
Page 49
Station Programming User Manual49 Confirming the assigned data on the Flexible button — Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9]. — To exit Station Programming mode: Press [PROGRAM] or lift the handset. — If you wish to change the data, follow the programming procedure explained in this section. Clearing the data on the Flexible button — Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9]. — To exit Station Programming mode: Press [PROGRAM]...
Page 50
Station Programming 50User Manual Station Programming [Flexible Button Assignment] (Station Programming) Direct Station Selection (DSS) Button One-Touch Dialing Button Message Waiting (MESSAGE) Button FWD/DND Button SAVE Button Account Button Conference (CONF) Button Log-In / Log-Out Button Phantom Extension Button Night Button Voice Mail (VM) Transfer Button Two-Way Record Button Two-Way Transfer Button Live Call Screening (LCS) Button Live Call Screening (LCS) Cancel Button Single-CO (S-CO) Button...