Panasonic Kx Td500 User Manual

User Programming
User Manual131
3.2.6 [006] Caller ID Dial Set
Description
Sets the identification code of the calling party (Caller ID Code) to utilize Caller ID Service 
provided by a specific central office (CO). If an ID Code transmitted from CO is found in the 
Caller ID Code Table, the callers ID Code or a name given to the code in program [007] Caller 
ID Name Set is displayed on the telephone, allowing the called party to recognize the caller.
Selection
Location number: 000 through 999  
Caller...

User Programming
132User Manual
Programming
Conditions
Up to 1000 Caller ID Codes per tenant, 2000 per system, can be assigned.
Program [007] Caller ID Name Set is used to give names to Caller ID Codes. If an ID 
Code is given a name, the called partys telephone shows the name with the ID Code.
Display PT
Dial 006. Enter a location number
(000 through 999).
location no.

Press NEXT.
NEXT
 
Location NO?→
To enter location number 000,
you can also press NEXT.
   
000:Not Stored
Press END.
END

Repeat...

User Programming
User Manual133
Features Guide References
1.5 Attended Features
Caller ID Service 

User Programming
134User Manual
3.2.7 [007] Caller ID Name Set
Description
With Caller ID Service, the calling party is displayed either by its ID Code or by its name. If 
the name display is required, use this program to give a name to a Caller ID Code stored in 
program [006] Caller ID Dial Set.
Selection
Location number: 000 through 999 
Caller ID Name: 16 characters (max.) consisting of 0 through 9, A through Z, a through 
z or the following marks: ! # $ % &     ( ) + , - . / : ; < = > ? @
Default...

User Programming
User Manual135
Programming
Conditions
Up to 1000 Caller ID Names per tenant, 2000 per system, can be assigned. Each name 
corresponds to a Caller ID Code programmed by [006] Caller ID Dial Set. 
A Caller ID Name cannot be assigned if the corresponding Caller ID Dial is not assigned.
For entering characters, please refer to Section 2.2.17 Station Speed Dialing Number/
Name Assignment [KX-T7235/KX-T7431/KX-T7433/KX-T7436 only].
Display PT
Dial 007. Enter a location number
(000 through...

User Programming
136User Manual
Features Guide References
1.5 Attended Features
Caller ID Service 

User Programming
User Manual137
3.2.8 [008] Absent Messages Set
Description
Used to program the absent messages. An absent message, if set by the extension user, is 
displayed on the display of calling extensions PT to show the reason for the users absence.
Selection
Message number: 1 through 9 
Message: 16 characters (max.)
Default
1: Will Return Soon
2: Gone Home
3: At Ext %%%%
4: Back at %%:%%
5: Out Until %%/%%
6: In a Meeting
7: through 9: Blank (not stored) 

User Programming
138User Manual
Programming
Display PT
Dial 008. Enter a message number
(1 through 9).
message no.

Press NEXT.
NEXT
 
MSG NO?→
To enter message number 1, you
can also press NEXT.

MSG1:Will Return
Press END.
END
 [When SELECT is pressed]
Repeat these steps
Enter the message.
message
Press STORE.
Press NEXT or
PREV or SELECT.Enter the desired message
number (1 through 9).
message no.
To delete the current entry, press CLEAR. 
To change the current entry, press CLEAR
and enter the new...

User Programming
User Manual139
Conditions
There is a maximum of nine messages. Messages 1 through 6 are programmed at the factory 
but can be changed. Each message has a maximum of 16 characters.
For entering characters, please refer to Section 2.2.17 Station Speed Dialing Number/
Name Assignment [KX-T7235/KX-T7431/KX-T7433/KX-T7436 only].
You can enter a maximum of seven % characters per message which can be programmed 
at each users station. The extension user can enter 0 through 9,   and # for the...

User Programming
140User Manual
3.2.9 [009] Quick Dial Number Set
Description
Stores up to eight quick dial numbers.
Selection
Location number: 1 through 8
Desired number: 24 digits (max.)
Default
All location numbers — Not Stored