Panasonic Kx Td500 User Manual

Station Features and Operation (PT/SLT)
User Manual181
Conditions
[General]
Types of calls which are forwarded by these features are:
– Items marked with * are not available with Call Forwarding — No Answer to CO/TIE 
feature.
Forwarded call is not forwarded furthermore
Call Forwarding can only be extended to one target extension. For example, extension A 
is forwarded to extension B, and extension B is forwarded to extension C. A call to 
extension A is forwarded to extension B, but the call would not...

Station Features and Operation (PT/SLT)
182User Manual
Confirmation tone
Confirmation tone 2 (two beeps) is sent when the previously programmed data is same as 
the new data. If it is not, confirmation tone 1 (one beep) is sent. Please refer to Section 
6.1.3 Tone List for further information on tones.
You can call the original extension from the Call Forwarding destination extension.

Both the Call Forwarding and Do Not Disturb (DND) features can be programmed at the 
same time, but either one of...

Station Features and Operation (PT/SLT)
User Manual183
[To CO / TIE Line]
Class of Service
Class of Service programming determines the extension that can perform this feature 
.
Treatment of the forwarded call
Toll Restriction, Automatic Route Selection (ARS) and Account Code Entry requirements 
of the extension in Call Forwarding mode still apply to the call forwarded by this feature. 
If you are storing an account code, enter the account code and then the delimiter 99 before 
the line access code....

Station Features and Operation (PT/SLT)
184User Manual
Co-to-CO Line Call
If a call between two outside parties is established by this feature, the call duration is 
determined by System Programming .
An alarm tone is sent to both outside parties 15 seconds before the time-out. The call is 
disconnected at the time-out.
Trunk-to-Trunk Connection 
Before utilizing this feature, Trunk to Trunk Restriction should be enabled by System 
Programming.
You can store the telephone number up to 24 digits. Valid...

Station Features and Operation (PT/SLT)
User Manual185
1.8 Ringing Features
Do Not Disturb (DND)
1.11 Transferring Features
Call Forwarding
3.1 TIE Line Features
TIE Line and Outside (CO) Line Connection
User Manual References
2.2.3 Flexible Button Assignment
3.2.5 [005] Flexible CO Button Assignment
4.3.27 Do Not Disturb (DND)
4.3.83 VPS Integration 

Station Features and Operation (PT/SLT)
186User Manual
4.3.10 Call Forwarding — All Calls to an Incoming Group
Automatically transfers all calls to an Incoming Group to the pre-assigned Incoming Group or 
Extension Group.
Setting
Canceling
PT and SLT
Lift the handset or press
SP-PHONE/MONITOR.Confirmation tone
and dial tone 
FDN
Enter the FDN for a 
source Incoming
Group (3 or 4 digits).Dial 7141.
174

G-FWD
1
Hang up or press
SP-PHONE/MONITOR.
FDN
Enter the FDN for a 
destination Incoming/
Extension...

Station Features and Operation (PT/SLT)
User Manual187
Conditions
Types of calls which are forwarded by this feature are:
Class of Service (COS) programming
COS programming  determines the extension that can perform this feature. 
The Call Forwarding setting extension varies depending on the following three modes:
Disable:
Disables this feature.
Own Group(s):
Enables forwarding all calls to other Incoming Groups or Extension Groups. Only its own 
group(s) can be set as the Call Forwarding setting...

Station Features and Operation (PT/SLT)
188User Manual
While setting, you can temporarily cancel this feature by pressing the Group FWD button. 
Pressing the Group FWD button alternates between setting and canceling the mode.
The lighting patterns of the Group FWD button are as follows:
Off: This feature is not set.
Red on: Group FWD mode
The Group FWD button cannot be used to store or cancel this feature.
Please use the feature number for Group FWD instead.
Programming Guide References
2.3 Numbering...

Station Features and Operation (PT/SLT)
User Manual189
4.3.11 Call Hold
You can place a call (intercom or outside) on hold (Call Hold). While the call is on hold, you 
can make or receive other calls. The held call can be retrieved not only from your extension but 
from any other extension in the same tenant (Call Hold Retrieve).
Preventing other extension users from retrieving a call held at your extension is also possible 
[PT user only] (Exclusive Call Hold). In this case, the call can only be...

Station Features and Operation (PT/SLT)
190User Manual
Retrieving an outside call held at another extension
Retrieving an intercom call / an outside call held at another extension
PT and SLT
PT
Enter the held
trunk port physical
number. Dial 53.
trunk port physical no.
Lift the handset or press
SP-PHONE/MONITOR.Confirmation
tone
(optional)
At another extension;
53
The CO indicator light
turns steady green.
Press CO whose indicator
is flashing red slowly.
At another extension;
(CO)
Confirmation
tone...