Home > Panasonic > Wireless PBX > Panasonic Kx Taw848 PC Cprogramming Manual

Panasonic Kx Taw848 PC Cprogramming Manual

Here you can view all the pages of manual Panasonic Kx Taw848 PC Cprogramming Manual. The Panasonic manuals for Wireless PBX are available online for free. You can easily download all the documents as PDF.

Page 81

2.7 [1] Configuration
PC Programming Manual 81
Value Range
0 (no limit), 1, 2, 3
Maintenance Console Location
2.7.7 [1-1] Slot—LCO Card Property
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Caller ID—Caller ID (FSK) Carrier Detection
Enables the PBX to detect the carrier when receiving Caller ID. To enable this setting, Caller ID—
Caller ID Signalling on this screen should be set to FSK.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.7.7 [1-1]...

Page 82

2.7 [1] Configuration
82 PC Programming Manual
Feature Manual References
1.3.1 Caller ID
Caller ID—Caller ID (FSK) Header Examination
Enables the PBX to check the header of received Caller ID information. To enable this setting, Caller 
ID—Caller ID Signalling on this screen should be set to FSK.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.7.7 [1-1] Slot—LCO Card Property
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Caller ID—Caller ID (FSK)...

Page 83

2.7 [1] Configuration
PC Programming Manual 83
Default
2000 ms
Value Range
80 × n (n=13–50) ms
Maintenance Console Location
2.7.7 [1-1] Slot—LCO Card Property
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
2.7.8 [1-1] Slot—LCO Port
Various settings can be programmed for each analog CO line port. 
To change the status of ports, click Command.
Slot
Indicates the slot position (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location...

Page 84

2.7 [1] Configuration
84 PC Programming Manual
Value Range
Port number
Maintenance Console Location
2.7.8 [1-1] Slot—LCO Port
Programming Manual References
None
Feature Manual References
None
Connection
Indicates the port status (reference only). 
This column offers two ways to open the screen to select the port command:
 Click the desired cell in the column.
 Select the desired cell in the column, and then click Command.
Default
Current status
Value Range
INS: The port is in service.
OUS: The port is...

Page 85

2.7 [1] Configuration
PC Programming Manual 85
Programming Manual References
None
Feature Manual References
1.4.2 Dial Mode Selection
CPC Signal Detection Time—Outgoing, Incoming
Specifies the length of time required by the PBX to detect a CPC signal on outgoing or incoming CO 
line calls before disconnecting the line. When None is selected here, the line will not be disconnected 
when a CPC signal is not detected.
Default
400 ms
Value Range
None, 6.5 ms, 8 × n (n=1–112) ms
Maintenance Console Location...

Page 86

2.7 [1] Configuration
86 PC Programming Manual
Pulse Speed
Selects the speed at which pulse dials are sent to the analog CO line.
Default
Low
Value Range
Low, High
Maintenance Console Location
2.7.8 [1-1] Slot—LCO Port
Programming Manual References
None
Feature Manual References
None
Caller ID Detection
Enables the PBX to detect a Caller ID signal from the analog CO line.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.7.8 [1-1] Slot—LCO Port
Programming Manual References
2.7.7...

Page 87

2.7 [1] Configuration
PC Programming Manual 87
Maintenance Console Location
2.7.8 [1-1] Slot—LCO Port
Programming Manual References
None
Feature Manual References
1.8.5 Host PBX Access Code (Access Code to the Telephone Company from a Host PBX)
1.13.4 Pause Inser tion
1.16.2 Special Carrier Access Code
Flash Time
Specifies the length of a flash signal.
Default
608 ms
Value Range
None, 16 × n (n=1–255) ms
Maintenance Console Location
2.7.8 [1-1] Slot—LCO Port
Programming Manual References
None
Feature...

Page 88

2.7 [1] Configuration
88 PC Programming Manual
Feature Manual References
1.6.2 Flash/Recall/Terminate
2.7.9 [1-1] Slot—LCO Port—Port Command
Commands for the LCO ports can be programmed.
INS
Puts the port in service.
Default
Not applicable.
Value Range
Not applicable.
Maintenance Console Location
2.7.9 [1-1] Slot—LCO Port—Port Command
Programming Manual References
2.7.8 [1-1] Slot—LCO Port
Feature Manual References
None
OUS
Takes the port out of service. This enables a temporary non-use of the port, for...

Page 89

2.7 [1] Configuration
PC Programming Manual 89
2.7.10 [1-1] Slot—DPH Card Property
The status of the DPH ports can be viewed, and set to INS (in service) or OUS (out of service).
Slot
Indicates the slot position (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.7.10 [1-1] Slot—DPH Card Property
Programming Manual References
None
Feature Manual References
None
Por t Number
Indicates the por t number (reference only).
Default
Current port number
Value...

Page 90

2.7 [1] Configuration
90 PC Programming Manual
 Select the desired cell in the column, and then click Command.
Default
Current status
Value Range
INS: The port is in service.
OUS: The port is out of service.
Fault: The port is not communicating with the network.
Maintenance Console Location
2.7.10 [1-1] Slot—DPH Card Property
Programming Manual References
2.7.11 [1-1] Slot—DPH Port Command
Feature Manual References
None
For Output (EIO)—Device Type
Selects the type of connected output device (for output...
Start reading Panasonic Kx Taw848 PC Cprogramming Manual

Related Manuals for Panasonic Kx Taw848 PC Cprogramming Manual

All Panasonic manuals