Panasonic Kx Taw848 PC Cprogramming Manual

2.7 [1] Configuration
PC Programming Manual 61
2.7.2 [1-1] Slot—Summary
Summary information is displayed for all cards installed in the PBX.
Slot
Indicates the slot number (reference only).
Default
Current slot number
Value Range
Available slot numbers.
Maintenance Console Location
2.7.2 [1-1] Slot—Summary
Programming Manual References
None
Feature Manual References
None
Slot Type
Indicates the type of each slot (reference only).
Default
Not applicable.
Value Range
Fixed Slot: For initially installed 4...

2.7 [1] Configuration
62 PC Programming Manual
Feature Manual References
None
Card Type
Indicates the type of service card installed in each slot of the PBX (reference only). 
Note that for MPR cards, the PBX model code is displayed in parentheses after the name.
Default
Slot 00: MPR (Main Processing Card: fixed)
Other slots: Not stored.
Value Range
HLC4: 4-Port Hybrid Extension Card
PLC4: 4-Port Proprietary Extension Card
PLC8: 8-Port Proprietary Extension Card
SLC8: 8-Port Single Line Telephone...

2.7 [1] Configuration
PC Programming Manual 63
Value Range
INS: The port is in service.
OUS: The por t is out of service.
Fault: The port is not communicating with the network.
Pre-Install: A card has been added to the slot in batch programming mode.
Idle: No card is installed in the slot..
Maintenance Console Location
2.7.2 [1-1] Slot—Summary
Programming Manual References
2.7.1 [1-1] Slot
Feature Manual References
None
2.7.3 [1-1] Slot—Extension Card Property
The property for the extension cards can be...

2.7 [1] Configuration
64 PC Programming Manual
Value Range
8 × n (n=3–255) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None
Feature Manual References
None
SLT Off Hook Guard Time
Specifies the length of guard time used for off-hook signals from SLTs, to prevent the PBX mistaking 
them for pulse dials.
Default
504 ms
Value Range
8 × n (n=12–63) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References...

2.7 [1] Configuration
PC Programming Manual 65
Feature Manual References
None
SLT Pulse Minimum Make Width
Specifies the minimum length of the make signal in a pulse dial.
Default
8 ms
Value Range
8 × n (n=1–5) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None
Feature Manual References
None
SLT Flash Detection
Enables the PBX to detect the flash signal sent when an SLT user presses the hookswitch or the 
Flash/Recall button.
Default
Enable
Value...

2.7 [1] Configuration
66 PC Programming Manual
Default
112 ms
Value Range
8 × n (n=3–63) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None
Feature Manual References
None
Flash Timing - Range
Specifies the maximum length that a signal sent from an SLT can be for the PBX to recognize it as a 
hookswitch flash signal.
Default
904 ms
Value Range
8 × n (n=3–191) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual...

2.7 [1] Configuration
PC Programming Manual 67
Programming Manual References
None
Feature Manual References
None
2.7.4 [1-1] Slot—Extension Port
Various settings can be programmed for each extension port. 
To change the status of extension ports, click Command. To view total numbers of each type of 
extension connected, click Por t Type View.
Slot
Indicates the slot position (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port...

2.7 [1] Configuration
68 PC Programming Manual
Feature Manual References
1.5.7 Extension Port Configuration
Por t Type
Indicates the port type (reference only).
Default
Current port type
Value Range
APT: APT port (PLC) 
SLT: SLT port (SLC) 
Hybrid: Hybrid port (HLC)
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port
Programming Manual References
None
Feature Manual References
1.5.7 Extension Port Configuration
Telephone Type
Indicates the connected telephone type (reference only). 
The number...

2.7 [1] Configuration
PC Programming Manual 69
Connection
Indicates the por t status (reference only). 
This column offers two ways to open the screen to select the por t command as follows:
 Click the desired cell in the column.
 Select the desired cell in the column, and then click Command.
Default
Current status
Value Range
INS: The port is in service.
OUS: The por t is out of service.
Fault: The port is not communicating with the PBX.
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port...

2.7 [1] Configuration
70 PC Programming Manual
Feature Manual References
None
Extension Name
Specifies the extension name of the port.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port
Programming Manual References
None
Feature Manual References
None
DPT Type—Type (for Hybrid port)
Selects the port type.
To change the port type of an extension port, follow the steps below:
1.Set the status of the extension port to OUS.
2.Change the port type...