Panasonic Kx Taw848 Feature Manual

4.2 System [2]
Feature Guide 321
Master CS Port
Indicates the location of the master CS port (reference only).
Radio System ID
Indicates the radio system ID used to register a PS (reference only).
Call Pickup by DSS Key for Direct Incoming Call
Specifies whether a DSS button will light up or flash when a call rings at the specified 
extension. To enable this setting, DSS Key mode for Incoming call on this screen must be 
set to ON or Flash.
Call Pickup by DSS Key for ICD Group Call
Specifies whether a...

4.2 System [2]
322 Feature Guide
DSS Key mode for Incoming call
Enables the use of a DSS button to pick up an incoming call to another extension or an ICD 
group.
4.2.24 Audio Gain—Paging/MOH [2-10-1]
Gain levels for the External Pager/External BGM ports can be programmed.
EPG (External Pager)
Specifies the paging volume on the External Pager.
MOH (Music On Hold)
Specifies the music volume on the External BGM.
Feature Guide References
Feature References
1.4.1.3 Call Pickup
Programming References
None...

4.2 System [2]
Feature Guide 323
4.2.25 Extension Caller ID [2-11]
Various settings for extension Caller ID can be programmed.
Extension Caller ID Resource-1, 2
Specifies a group of 4 SLT ports that can send Caller ID information to an SLT.
When an extension has this feature activated, there will be a short delay before the extension 
rings for incoming calls.
Extension Caller ID Modulation Type
Specifies the modulation frequency to be used when sending Caller ID information to an SLT.
Channel Seizure...

4.2 System [2]
324 Feature Guide
Channel Seizure Wait Time
Specifies the length of time the PBX waits before starting to send the seizure signal following 
the first ring when sending Caller ID information to an SLT.
Additional Local Trunk Access Code to Extension Caller ID
Enables the PBX to automatically add a Trunk Access number to the received telephone 
number when sending a Caller ID number of an incoming trunk call to an SLT.
Send Date & Time of Extension Caller ID
Enables the PBX to send date and...

4.2 System [2]
Feature Guide 325
Send Name of Extension Caller ID
Enables the PBX to send caller’s name of an incoming call when sending Caller ID information 
to an SLT.
Send Long Distance of Extension Caller ID
Enables the PBX to send a call qualifier (Long Distance) when it is received from a trunk when 
sending Caller ID information to an SLT. DefaultEnable
Va lu e  Ra n g eDisable, Enable
Feature Guide References
Feature References
1.16.1 Caller ID
Programming References
None
DefaultEnable
Va lu e...

4.3 Groups [3]
326 Feature Guide
4.3 Groups [3]
4.3.1 Trunk Group—TRG Settings [3-1-1]
CO lines are grouped into CO line groups. The settings of the CO line groups determine the 
settings of their CO lines. A maximum of 64 CO line groups can be programmed.
Main
Group Name
Specifies the name of the CO line group for programming reference. As for the available 
characters, refer to the character code table described in section 3.2.1 Installing and Starting 
KX-TAW848 Maintenance Console.
COS
Specifies the...

4.3 Groups [3]
Feature Guide 327
DISA Tone Detection—Silence
Enables the disconnection of a DISA-originated CO-to-CO line call by silence detection.
DISA Tone Detection—Continuous
Enables the disconnection of a DISA-originated CO-to-CO line call by continuous signal 
detection.
DISA Tone Detection—Cyclic
Enables the disconnection of a DISA-originated CO-to-CO line call by cyclic signal detection.
Feature Guide References
Feature References
1.5.5.3 CO Line Access
2.2.2 Group
Programming References...

4.3 Groups [3]
328 Feature Guide
CO-CO Duration Time
Specifies the length of time a CO-to-CO line call can be maintained before being disconnected.
Extension-CO Duration Time
Specifies the length of time an extension-to-CO line call can be maintained before being 
disconnected.
Caller ID Modify Table
Specifies the table to be used for modifying the caller information (telephone number).Programming References
4.5.3 DISA—System Setting [5-3-1]
4.9.1 CO Line Setting [9-1]
Default10 min
Va lu e  Ra n g...

4.3 Groups [3]
Feature Guide 329
Intercept
Group Name
Specifies the name of the CO line group for programming reference. As for the available 
characters, refer to the character code table described in section 3.2.1 Installing and Starting 
KX-TAW848 Maintenance Console.
Intercept Destination—Day, Lunch, Break, Night
Specifies the intercept routing destination of unanswered calls (whose original destination is a 
floating extension number of a PS Ring Group, VM Group, External Pager [TAFAS], or DISA) 
in...

4.3 Groups [3]
330 Feature Guide
Host PBX Access Code 1–10
Specifies the feature number used to access a CO line from the host PBX.
4.3.2 Trunk Group—Local Access Priority [3-1-2]
CO line groups can be assigned a priority for Idle Line Access. When making a CO line call by 
Idle Line Access, the PBX will search CO line groups for an idle CO line according to a priority 
assigned here.
Trunk Group No. & Name
Specifies the CO line group assigned to the corresponding priority level.
4.3.3 Extension Group...