Panasonic Kx Taw848 Feature Manual

4.3 Groups [3]
Feature Guide 351
VM DTMF Status Signal—Reorder Tone
Specifies the DTMF status signal the PBX sends to the VPS when the dialed number is invalid.
VM DTMF Status Signal—DND tone
Specifies the DTMF status signal the PBX sends to the VPS when the called extension is in 
DND mode.
VM DTMF Status Signal—Answer
Specifies the DTMF status signal the PBX sends to the VPS when the called extension has 
answered the call.
Feature Guide References
Feature References
1.19.1 Voice Mail (VM) Group...

4.3 Groups [3]
352 Feature Guide
VM DTMF Status Signal—Confirm
Specifies the DTMF status signal the PBX sends to the VPS when a certain feature (e.g., 
Message Waiting) has been successfully set or canceled on an extension.
VM DTMF Status Signal—Disconnect
Specifies the DTMF status signal the PBX sends to the VPS when the caller hangs up.
VM DTMF Status Signal—FWD to VM Ringback Tone
Specifies the DTMF status signal the PBX sends to the VPS when the call has been forwarded 
to the VPS and the PBX is...

4.3 Groups [3]
Feature Guide 353
VM DTMF Status Signal—FWD to Extension Ringback Tone
Specifies the DTMF status signal the PBX sends to the VPS when the call has been forwarded 
to another extension and the PBX is calling the destination extension.
VM DTMF Command—Recording Message
Specifies the DTMF command the PBX sends to the VPS when a call is forwarded, intercepted, 
or transferred to the VPS, so that the caller can leave a message in a certain mailbox.
VM DTMF Command—Listening Message
Specifies...

4.3 Groups [3]
354 Feature Guide
VM DTMF Command—Switching to AA
Specifies the DTMF command the PBX sends to the VPS when in the VM Service Mode to 
activate the AA Service Mode instead.
VM DTMF Command—Switching to VM
Specifies the DTMF command the PBX sends to the VPS when in the AA Service Mode to 
activate the VM Service Mode instead.
Timing—DTMF Length for VM
Specifies the length of the DTMF signal the PBX sends to the VPS.
Timing—Inter-digit Time
Specifies the length of pause time between DTMF...

4.3 Groups [3]
Feature Guide 355
Timing—Waiting Time before Sending Follow on ID 
Specifies the length of time the PBX waits before sending the Follow on ID to the VPS after the 
VPS has answered a call.
Timing—Waiting Time before Sending VM DTMF Status Signal
Specifies the length of time the PBX waits before sending the DTMF status signal to the VPS 
after the VPS has finished dialing.
Others—Call Waiting on VM Group 
Enables the queuing of calls when all extension ports of the VM (DTMF) group are busy....

4.3 Groups [3]
356 Feature Guide
Others—Intercept Routing to the VPS Sequence
Specifies which DTMF commands the VPS receives from the PBX when a call is intercepted 
to the VPS, so that the VPS can answer the call either with a mailbox or in the AA service mode. 
It is also possible to send no DTMF signal to the VPS.
Others—Mailbox for Extension
Specifies whether the mailboxes use the same numbers as the extensions and incoming call 
distribution groups, or use different numbers as programmed for each...

4.3 Groups [3]
Feature Guide 357
4.3.13 VM(DTMF) Group—Group Setting [3-8-2]
A VM (DTMF) group has a floating extension number, and can be assigned as the destination 
for redirected calls and incoming calls.
Floating Ext No.
Specifies the floating extension number of the VM (DTMF) group.
Group Name
Specifies the name of the VM (DTMF) group, which will be shown on the display of the 
extension that has called the VM (DTMF) group. As for the available characters, refer to the 
character code table...

4.3 Groups [3]
358 Feature Guide
Extension Number of the SLT Port Connected to VM 1–24
Specifies the extension number of the SLT ports that belongs to the VM (DTMF) group.
To assign an extension port to a VM (DTMF) group, follow the steps below:
1.Type the extension number of the SLT port that belongs to the VM (DTMF) group.
2.Set the status of the extension port to OUS, then INS.
4.3.14 PS Ring Group [3-9]
PS ring group is a group of PS extensions that receives incoming calls. Each group has a 
floating...

4.3 Groups [3]
Feature Guide 359
Incoming Trunk Call Information Display
Specifies the information of the incoming CO line call to be shown on the displays of the PSs 
that belong to the PS ring group. If the caller’s name or called party’s name is not recognized, 
the telephone number will be shown.
Portable Station 1–28
Specifies whether the PS belongs to the PS ring group. A PS can be assigned to a PS ring 
group, even when the PS is working in parallel with a wired telephone (in Wireless XDP Parallel...

4.4 Extension [4]
360 Feature Guide
4.4 Extension [4]
4.4.1 Wired Extension—Extension Settings [4-1-1]
For each slot in which an extension card is installed, a certain number of extension ports are 
displayed. For each extension port, various extension settings can be assigned.
Main
Slot
Indicates the slot position of each extension card (reference only).
Port
Indicates the port number (reference only).
Extension Number
Specifies the extension number of the extension.
To change the extension number of a...