Panasonic Kx Taw848 Feature Manual

4.2 System [2]
Feature Guide 271
Unattended Conference : Recall Start Time
Specifies the length of time until the conference originator receives an Unattended Conference 
Recall tone.
Unattended Conference : Recall Continuous Time before Sending Alarm Tone to CO
Specifies the length of time until the parties involved in the Unattended Conference receive an 
alarm tone after the conference originator has received the Unattended Conference Recall 
tone but remained unattended to the conference.
Unattended...

4.2 System [2]
272 Feature Guide
Busy Tone / DND Tone Continuation Time
Specifies the length of time a busy/DND tone is heard when a call is made to an extension in 
busy status or DND mode. A reorder tone will be sent when this timer expires. (For a call 
through DISA, the call will be disconnected when this timer expires.)
Reorder Tone Continuation Time for PT Handset Mode
Specifies the length of time a reorder tone is heard from the handset of a PT. The PT will return 
to idle status when this timer...

4.2 System [2]
Feature Guide 273
DTMF Length while talking
Specifies the length of time a DTMF signal is sent when a number is dialed from a PT or PS 
during a conversation.
DTMF Inter Digit Pause while talking
Specifies the length of time between DTMF signals when numbers are dialed in succession 
from a PT or PS during a conversation.
Pause Time while talking
Specifies the length of the pause inserted when the PAUSE button is pressed during a 
conversation.
Waiting Timer to Receive Analog Caller ID...

4.2 System [2]
274 Feature Guide
Visual Caller ID Display Timer
Specifies the length of time the Caller ID number, with the Call Waiting tone offered by an 
analog line from the telephone company, is shown on the display. The Caller ID number flashes 
on the display twice for five seconds at 15-second intervals. 
4.2.8 Time Service—Week Table [2-5-1]
A specific time mode (day, night, lunch, or break) can be selected for operation depending on 
the time of the day. The time mode can be switched either...

4.2 System [2]
Feature Guide 275
Day 1 Start—Minute
Specifies the minute of the Day 1 start time.
Lunch Start—Setting
Enables the setting of the Lunch start time.
Lunch Start—Hour
Specifies the hour of the Lunch start time. Default9
Va lu e  Ra n g e0–23
Feature Guide References
Feature References
2.2.4 Time Service
Programming References
4.2.14 Class of Service—COS Settings [2-7-1]
4.3.3 Extension Group [3-2]
Default0
Va lu e  Ra n g e0–59
Feature Guide References
Feature References
2.2.4 Time...

4.2 System [2]
276 Feature Guide
Lunch Start—Minute
Specifies the minute of the Lunch start time.
Day 2 Start—Setting
Enables the setting of the Day 2 start time (Lunch end time).
Day 2 Start—Hour
Specifies the hour of the Day 2 start time.
Day 2 Start—Minute
Specifies the minute of the Day 2 start time.Programming References
4.2.14 Class of Service—COS Settings [2-7-1]
4.3.3 Extension Group [3-2]
Default0
Va lu e  Ra n g e0–59
Feature Guide References
Feature References
2.2.4 Time Service
Programming...

4.2 System [2]
Feature Guide 277
Night Start—Setting
Enables the setting of the Night start time.
Night Start—Hour
Specifies the hour of the Night start time.
Night Start—Minute
Specifies the minute of the Night start time.
Feature Guide References
Feature References
2.2.4 Time Service
Programming References
4.2.14 Class of Service—COS Settings [2-7-1]
4.3.3 Extension Group [3-2]
DefaultEnable
Va lu e  Ra n g eDisable, Enable
Feature Guide References
Feature References
2.2.4 Time Service
Programming...

4.2 System [2]
278 Feature Guide
Break
Break start and end times can be programmed for each day of the week for Time Tables that 
contain breaks.
Break 1, 2, 3 Start—Setting
Enables the setting of each break mode start time.
Break 1, 2, 3 Start—Hour
Specifies the hour of each break mode start time.
Break 1, 2, 3 Start—Minute
Specifies the minute of each break mode start time.
Break 1, 2, 3 End (Day Mode)—Setting
Enables the setting of each break mode end time (back to day mode). DefaultDisable
Va lu e...

4.2 System [2]
Feature Guide 279
Break 1, 2, 3 End (Day Mode)—Hour
Specifies the hour of each break mode end time.
Break 1, 2, 3 End (Day Mode)—Minute
Specifies the minute of each break mode end time.
4.2.9 Time Service—Holiday Table [2-5-2]
A specific time mode (day, night, lunch, or break) can be selected for operation during holidays. 
Select the desired time mode from the Holiday Mode list. The start and end dates of a 
maximum of 24 different holidays can be programmed.
Setting
Enables the setting...

4.2 System [2]
280 Feature Guide
Start Date—Month
Specifies the month of the holiday start date.
Start Date—Day
Specifies the day of the holiday start date.
End Date—Month
Specifies the month of the holiday end date.
End Date—Day
Specifies the day of the holiday end date.
Feature Guide References
Feature References
2.2.4 Time Service
Programming References
None
Default1
Va lu e  Ra n g e1–12
Feature Guide References
Feature References
2.2.4 Time Service
Programming References
None
Default1
Va lu e...