Panasonic Kx Taw848 Feature Manual

3.3 PT Programming
Feature Guide 231
3.3.11 Card Programming
Slot Card Type Reference [900]
Slot Card Deletion [901]
Slot Card Reset [902]
[900]01–11 Reference onlySlot No.Card Name
STOREEND
[901]
01–11Slot No.Delete
To the Next Slot No.
NEXT Confirming the 
deleting operation.
STORESTOREEND
[902]
01–11Slot No.ResetConfirming the 
resetting operation.STORESTOREEND 

3.3 PT Programming
232 Feature Guide 

Feature Guide 233
Section 4
KX-TAW848 Maintenance Console Operating
Instructions 

4.1 Configuration [1]
234 Feature Guide
4.1 Configuration [1]
4.1.1 Slot [1-1]
The operating characteristics associated with each service card can be programmed.
Slot Type
Indicates the type of each slot (reference only).
Card Type
Indicates the type of service card that is installed or pre-installed in each slot (reference only).
This column offers two ways to open the screen to specify the property of each card:
Click the desired card in the column.
Use the arrow keys to select the desired card in...

4.1 Configuration [1]
Feature Guide 235
Status
Indicates the status of the service card in each slot (reference only).
This column offers two ways to open the screen to select the card command:
Click the desired cell in the column.
Use the arrow key to select the desired cell in the column, and then click Command. Value Range Card Type:
HLC4: 4-Port Hybrid Extension Card
PLC8: 8-Port Proprietary Extension Card
PLC4: 4-Port Proprietary Extension Card
SLC8: 8-Port Single Line Telephone Extension Card...

4.1 Configuration [1]
236 Feature Guide
Versi o n
Indicates the version of the installed card (reference only).
4.1.2 Slot [1-1] Extension Card Property
The property for the extension cards can be specified.
SLT Pulse Dial Mode
Selects the type of pulse dial transmission appropriate to your area.
SLT Off Hook Time
Specifies the minimum time required by the PBX to recognize the pulse dial sent from an SLT 
as an off-hook signal. Va lu e  Ra n g eINS: The card is in service.
OUS: The card is out of...

4.1 Configuration [1]
Feature Guide 237
SLT Off Hook Guard Time
Specifies the length of time used to prevent the PBX from mistaking an off-hook signal as a 
pulse dial.
SLT Pulse Maximum Break Width
Specifies the maximum length of the break signal in a pulse dial. 
SLT Pulse Minimum Make Width
Specifies the minimum length of the make signal in a pulse dial.  Default160 ms
Va lu e  Ra n g e8 × n (n=3–255) ms
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]...

4.1 Configuration [1]
238 Feature Guide
SLT Flash Detection
Enables the PBX to detect a flash signal an SLT user sent by pressing the hookswitch or the 
Flash/Recall button.
Flash Timing - Min.
Specifies the minimum time before the PBX starts recognizing a hookswitch flash signal sent 
from an SLT.
Flash Timing - Range
Specifies the length of time required by the PBX to recognize a hookswitch flash signal sent 
from an SLT.
DTMF-R STD Detection Time
Specifies the minimum time required by the PBX to...

4.1 Configuration [1]
Feature Guide 239
4.1.3 Slot [1-1] LCO Card Property
The properties of the analog CO line cards can be specified.
Outgoing Guard Time
Specifies the length of time after a CO line is disconnected, during which the PBX cannot seize 
the line.
First Dial Timer (CO)
Specifies the minimum time that the PBX waits after seizing a CO line, before sending the 
dialed digits to the telephone company. This allows the telephone company to have enough 
time to accept the dialed digits...

4.1 Configuration [1]
240 Feature Guide
Bell Detection—Bell Start Detection Timer
Specifies the minimum time required by the PBX to confirm the bell signal sent from the 
telephone company, before the PBX detects an arriving call.
Bell Detection—Bell Off Detection Timer
Specifies the minimum time required by the PBX to confirm that the bell signal is no longer sent 
from the telephone company, before the PBX realizes the call is lost.
Pulse / DTMF Dial—DTMF Inter Digit Pause
Specifies the length of the...