Panasonic Kx Taw848 Feature Manual

							3.3 PT Programming
Feature Guide 231
3.3.11 Card Programming
Slot Card Type Reference [900]
Slot Card Deletion [901]
Slot Card Reset [902]
[900]01–11 Reference onlySlot No.Card Name
STOREEND
[901]
01–11Slot No.Delete
To the Next Slot No.
NEXT Confirming the 
deleting operation.
STORESTOREEND
[902]
01–11Slot No.ResetConfirming the 
resetting operation.STORESTOREEND 
						

							3.3 PT Programming
232 Feature Guide 
						

							Feature Guide 233
Section 4
KX-TAW848 Maintenance Console Operating
Instructions 
						

							4.1 Configuration [1]
234 Feature Guide
4.1 Configuration [1]
4.1.1 Slot [1-1]
The operating characteristics associated with each service card can be programmed.
Slot Type
Indicates the type of each slot (reference only).
Card Type
Indicates the type of service card that is installed or pre-installed in each slot (reference only).
This column offers two ways to open the screen to specify the property of each card:
Click the desired card in the column.
Use the arrow keys to select the desired card in the column, and then click Property. DefaultNot applicable.
Va lu e  Ra n g eFixed Slot: For initially installed 4 Hybrid ports
Free Slots Type A (02–04): For LCOT4/HLC4/PLC4
Free Slots Type B (05–06): For PLC8/SLC8
Option Slots (08–09): For MSG2/DPH4/ECHO8/EXT-CID card
Option Slots (10–11): For MSG2/ECHO8/EXT-CID card
Installation Manual References
2.2.6 Installing/Removing the Optional Service CardsFeature Guide References
None
DefaultSlot 00: MPR (Main Processing Card: fixed)
Slot 01: HLC4 (Hybrid ports: fixed)
Slot 02: LCOT4 (4-Port Analog Trunk Card: installed by default)
Other slots: Not stored. 
						

							4.1 Configuration [1]
Feature Guide 235
Status
Indicates the status of the service card in each slot (reference only).
This column offers two ways to open the screen to select the card command:
Click the desired cell in the column.
Use the arrow key to select the desired cell in the column, and then click Command. Value Range Card Type:
HLC4: 4-Port Hybrid Extension Card
PLC8: 8-Port Proprietary Extension Card
PLC4: 4-Port Proprietary Extension Card
SLC8: 8-Port Single Line Telephone Extension Card
LCOT4: 4-Port Analog Trunk Card
MSG2: 2-Channel Message Card
DPH4: 4-Por t Doorphone Card
ECHO8: 8-Channel Echo Canceller Card
EXT-CID: Extension Caller ID Card
Maximum Quantity:
Extension card: 3 (1 in the Free Slots Type A; 2 in the Free Slots 
Ty p e  B )
Trunk card: 2
MSG2 card: 2
DPH4 card: 1
ECHO8 card: 1
EXT-CID card: 1
Installation Manual References
1.3.1 OptionsFeature Guide References
Feature References
None
Programming References
4.1.2 Slot [1-1] Extension Card Property
4.1.3 Slot [1-1] LCO Card Property
4.1.4 Slot [1-1] DPH Card Property
DefaultSlot 00: - (fixed)
Other slots: Current status 
						

							4.1 Configuration [1]
236 Feature Guide
Versi o n
Indicates the version of the installed card (reference only).
4.1.2 Slot [1-1] Extension Card Property
The property for the extension cards can be specified.
SLT Pulse Dial Mode
Selects the type of pulse dial transmission appropriate to your area.
SLT Off Hook Time
Specifies the minimum time required by the PBX to recognize the pulse dial sent from an SLT 
as an off-hook signal. Va lu e  Ra n g eINS: The card is in service.
OUS: The card is out of service.
Fault: The card has been removed from the slot, or is not 
communicating with the PBX.
Fault-OVER: The number of CO line and/or extension ports exceed 
the system capacity.
Fault-DIF: The card installed in the slot differs from the 
programmed card type.
Pre-Install: There is no card in the slot, but the card type is 
programmed for the slot.
Idle: There is no card in the slot, nor programming of the card type 
for the slot.
Feature Guide References
Feature References
None
Programming References
4.1.6 Slot [1-1] Card Command
DefaultCurrent version number
Va lu e  Ra n g eVersion number
Feature Guide References
None
DefaultNormal 
Va lu e  Ra n g eNormal, Sweden, New Zealand 
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1] 
						

							4.1 Configuration [1]
Feature Guide 237
SLT Off Hook Guard Time
Specifies the length of time used to prevent the PBX from mistaking an off-hook signal as a 
pulse dial.
SLT Pulse Maximum Break Width
Specifies the maximum length of the break signal in a pulse dial. 
SLT Pulse Minimum Make Width
Specifies the minimum length of the make signal in a pulse dial.  Default160 ms
Va lu e  Ra n g e8 × n (n=3–255) ms
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default504 ms
Va lu e  Ra n g e8 × n (n=12–63) ms
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default96 ms
Va lu e  Ra n g e8 × n (n=9–20) ms
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default8 ms
Va lu e  Ra n g e8 × n (n=1–5) ms
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1] 
						

							4.1 Configuration [1]
238 Feature Guide
SLT Flash Detection
Enables the PBX to detect a flash signal an SLT user sent by pressing the hookswitch or the 
Flash/Recall button.
Flash Timing - Min.
Specifies the minimum time before the PBX starts recognizing a hookswitch flash signal sent 
from an SLT.
Flash Timing - Range
Specifies the length of time required by the PBX to recognize a hookswitch flash signal sent 
from an SLT.
DTMF-R STD Detection Time
Specifies the minimum time required by the PBX to detect the DTMF tone. DefaultEnable
Va lu e  Ra n g eDisable: The PBX disconnects the line to prevent placing the call on 
hold.
Enable: The PBX places the call on consultation hold.
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default112 ms
Va lu e  Ra n g e8 × n (n=3–63) ms
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default904 ms
Va lu e  Ra n g e8 × n (n=3–191) ms
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default30 ms
Va lu e  Ra n g e2 × n (n=1–31) ms 
						

							4.1 Configuration [1]
Feature Guide 239
4.1.3 Slot [1-1] LCO Card Property
The properties of the analog CO line cards can be specified.
Outgoing Guard Time
Specifies the length of time after a CO line is disconnected, during which the PBX cannot seize 
the line.
First Dial Timer (CO)
Specifies the minimum time that the PBX waits after seizing a CO line, before sending the 
dialed digits to the telephone company. This allows the telephone company to have enough 
time to accept the dialed digits correctly.
CO Feed Back Tone
Specifies whether to turn on or turn off the pulse feedback tone. For outgoing CO line calls, the 
dialed number is toned out, which informs the extension user that the dialed number has been 
dialed out.
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default3 s
Va lu e  Ra n g e3–6 s
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default1.0 s
Va lu e  Ra n g e0.5 × n (n=1–16) s
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
DefaultYe s
Va lu e  Ra n g eNo, Yes 
						

							4.1 Configuration [1]
240 Feature Guide
Bell Detection—Bell Start Detection Timer
Specifies the minimum time required by the PBX to confirm the bell signal sent from the 
telephone company, before the PBX detects an arriving call.
Bell Detection—Bell Off Detection Timer
Specifies the minimum time required by the PBX to confirm that the bell signal is no longer sent 
from the telephone company, before the PBX realizes the call is lost.
Pulse / DTMF Dial—DTMF Inter Digit Pause
Specifies the length of the DTMF inter-digit pause. This allows the telephone company to have 
enough time to accept the dialed digits correctly.
Pulse / DTMF Dial—Pulse Inter Digit Pause
Specifies the length of the pulse inter-digit pause. This allows the telephone company to have 
enough time to accept the dialed digits correctly.
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default144 ms
Va lu e  Ra n g e24 × n (n=1–50) ms
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default6.0 s
Va lu e  Ra n g e1.0 s–15.0 s
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]
Default112 ms
Va lu e  Ra n g e16 × n (n=4–19) ms
Feature Guide References
Feature References
None
Programming References
4.1.1 Slot [1-1]