Panasonic Kx Ta308 User Manual

Telephone Features3-97
3.2 Telephone FeaturesP
Paging — DENY
A page sent to a built-in speaker can be denied by any extension in the system.
Setting
PT
Dial 7341#.Lift the handset or press 
SP-PHONE/MONITOR.Hang up or press 
SP-PHONE/MONITOR.
1437

Paging Deny
PT
Dial 7340#.Lift the handset or press 
SP-PHONE/MONITOR.Hang up or press 
SP-PHONE/MONITOR.
0437

Paging Allow
Canceling 

3-98Telephone Features
P3.2 Telephone Features
Paralleled Telephone Connection
Any extension can be connected in parallel with a proprietary telephone and a single line
telephone. In the event of a power failure, CO1 can be accessed using the single line
telephone that is connected in parallel with the proprietary telephone to jack number 01.
If the extension receives a call, ringing will be heard from the proprietary telephone and
the single line telephone. You can answer the call by using either the...

Telephone Features3-99
3.2 Telephone FeaturesP
Personal Speed Dialing
Allows you to store up to ten speed dial numbers at your extension. These numbers are
available for your extension only.
Storing a phone number
Any Telephone
Confirmation 
tone Lift the handset 
or press 
SP-PHONE/
MONITOR.
Dial 2   .Enter the personal speed 
dial number (0 through 9).
personal speed dial no.
Enter the 
desired number.
desired no.
Dial #.Hang up or press SP-PHONE/MONITOR.
2
Any Telephone
Lift the handset or press...

3-100Telephone Features
P3.2 Telephone Features
Conditions
•An account code must be stored by pressing “” and entering the account code after
the line access code in the account code verify-all and forced modes.
•You can store an extension number, telephone number, or feature number of up to
twenty-four digits. Valid digits are “0 through 9”.
•A pause can be stored by pressing the  key. However, in the account code verify-all,
verify-toll and forced modes, “” is not regarded as a pause.
•To store the...

Telephone Features3-101
3.2 Telephone FeaturesP
Conditions
•This feature will not work if you answer an incoming call or retrieve a call on hold.
•Up to thirty-two digits, consisting of “0 through 9” and “”, can be stored. The “”
button is used as a PAUSE. However, in the account code verify-all, verify-toll and
forced modes, “” is not regarded as a pause.
•An account code must be stored by pressing “” and entering the account code after
the line access code in the account code verify-all and forced...

3-102Telephone Features
P3.2 Telephone Features
Power Failure Transfer
During a power failure, the following outside (CO) line will be connected to an assigned
extension.
Outside (CO) line 1: jack number 01
Conditions
•During a power failure, all features cannot be used except for incoming and outgoing
outside calls from jack number 01.
•If jack number 01 is connected to a proprietary telephone, disconnect the unit and
connect a single line telephone. 

Telephone Features3-103
3.2 Telephone FeaturesP
Condition
•You cannot change from Tone to Pulse dialing mode.
Pulse to Tone Conversion 
Allows you to change the dialing mode from Pulse to Tone to access services that require
tones, such as computer telephone services.
Any Telephone
Dial    #.Enter the phone number 
(Pulse mode).
phone no. (Pulse mode)desired no. (Tone mode)
Enter the desired number 
(Tone mode). 

3-104Telephone Features
R3.2 Telephone Features
Conditions
•Up to sixty-four digits can be stored and redialed. This does not include an outside
(CO) line access code.
•If you hear a busy tone when attempting to redial, select another line and press the
REDIAL button or feature number.
•The stored number will be replaced even if only one digit is dialed the next time an
outside call is made. Dialing an outside (CO) line access code will not affect the stored
number.
•“ ”, “#”, “PAUSE”, and “INTERCOM”...

Telephone Features3-105
3.2 Telephone FeaturesR
Conditions
• Up to sixty-four digits can be stored and redialed. This does not include an outside(CO) line access code.
• “ ”, “#”, “PAUSE”, and “INTERCOM” (for secret dialing) are counted as one\
 digit.
• A flexible button can be assigned as the SAVE button.
• You can check the stored number. Press the pre-assigned SAVE button while on-hook, and the stored number will be displayed.
• You can change the outside (CO) line when dialing. You may press a CO...

3-106Telephone Features
R3.2 Telephone Features
Room Monitor
Allows you to monitor a room through a proprietary telephone with an
AUTO ANSWER/MUTE button. The proprietary telephone you want to monitor should
be prepared for monitoring beforehand. You can also monitor through a doorphone. You
can use a proprietary telephone with an AUTO ANSWER/MUTE button and single line
telephone with a MUTE button for monitoring.
Setting a monitored PT
PT
Lift the handset or 
press SP-PHONE.Press AUTO ANSWER/MUTE.Dial...