Panasonic Kx-T123210 Installation Manual

until the desired time appears 
lsec : dials after 1 second 
2sec : dials after 2 seconds 
3sec : dials after 3 seconds . . . . . . . . . default 
4sec : dials after 4 seconds 
Description 
Enables programming of the pickup dial (on 
page 5-17) start time (the delay between 
picking up the handset and automatic dialing). 
The default is 3 sec.,Which can be changed to 1, 
2, or 4 sec. 
Programming Table 
See page 7-6. 
Programming 
1. Dial (21). 
“Pickup Dial Time” will be displayed. 
2. Press the NEXT...

............................................. . AB= 111 : to limit the time to 1 minute 
: to limit the time to IO minutes.. .... default 
I : to limit the time to 32 minutes 
Description 
Enable limiting of the time any outside line can be 
used when “Call Transfer-To Outside Line” (on 
page 4-19) or “Call Forwarding-To Outside Line” 
(on page 4-28) is used to forward a outside call 
to an outside line. 
Conditions 
0 To erase a wrong entry, press the CLEAR 
button. 
Programming Table 
See page 7-7....

Description 
SMDR is a cost saving feature that records on a printer a record of all incoming and outgoing calls. 
The following information is provided on the printout. 
The SMDR will print out the security code of the long distance service. ( MCI, SPRINT etc. ) 
NOTE : 
When plugging a printer into the KX-T123210 make sure that the printer power is off. 
Select the RS-232C Communication Parameters, SMDR Parameters, Incoming/Outgoing Call Selection for printing, 
Secret Speed Dial/One Touch Dial...

(Carriage return for a new line) 
(Baud rate) 
until the desired baud rate appears 
- 110B 
150B 
300B 
600B 
1200B . . . . . . . . . . . . . default 
2400B 
4800B 
_ 9600B 
(Word length) 
(Parity) 
I . . . . . . . . . . . . until the desired mode appears 
- None 
Mark . . . . . . default 
Space 
Even 
_ Odd 
(Stop bit length) 
: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . until the desired mode appears 
3-32  

Carriage return for a new line 
A new line code indicates’what type of code is 
needed for the print head on a printer to move the 
first character position on the next line. 
when “CR + LF” is required from 
when “CR” is required from a printer. 
CR=Carriage Return 
LF=Line Feed. 
Baud rate 
A baud rate code indicates the data transmission 
speed from the system to a printer. 
-1lOB 
150B 
300 B 
600 B 
1200 B 
2400 B 
4800 B 
9600 B : when 110 baud is required. 
when 150 baud is required. 
when 300...

Programming 
1. Dial (23). 12. 
“RS232C Parameter” will be displayed. 
2. 
Press the NEXT button. 
“NI-Code : CR + LF” will be displayed and 
“CR+ LF” will blink. 
13. 
14. 
3. Press the SELECT button to alternate 
between 
“CR+LF and “CR” to select the 
desired mode. 
15. 
4. Press the MEMORY button. 
The LCD will stop blinking. 
5. Press the NEXT button. 
“Baud Rate : 12008” will be displayed and the 
“12006” will blink. 
16. 
17. 
6. Repeat pressing the SELECT button until the 
desired baud rate is...

(Page length) , 
(Skip perforation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ABa : 4 lines 
k;k[ : 66 lines ....... default 
Page length 
The page length may be selected to position a 
title and data on each page. 
A page length code indicates the number of 
lines per page. 
A title will be printed on the first 3 lines of each 
page. 
I 
4 lines per page 
99 99 lines per page 
STANDARD CONTINUOUS PAPER(ll inches) 
I 
paw z 66 lines z 
‘engtj i 1 i 
.~ _____...._......

f.. .......................... until the desired mode appears 
Outgoing : On ...... to print outgoing calls ...... default 
Outgoing : Off ...... to stop printing 
, ...... 
until the desired mode appears 
Incoming : On ...... to print incoming calls ...... default 
Incoming : Off ...... to stop printing 
InIInnIIIIEl 25 NEXT SELECT MEMORY NEXT SELECT MEMORY END 
Description 4. Press the MEMORY button. 
It is possible to print either outgoing outside 
calls, incoming outside calls or both. The LCD will...

0 stop output 
I~~~~~~~~~~~~~~~~~~~- until the Stop Output appears 
l All Parameters ,.................................... 
l System Parameter 
l Speed Call until desired data dump mode appears 
All Para . . . . . . . . . . . . . . . . . . . . . . . . default 
System Para 
co 
Para 
EXT 
Para 
DSS Para 
Speed Call 
stop output 
l CO Parameter (Outside) 
~~~~~~~~~~~~~~~~~~~~~ until the CO Para appears 
AB=m : to assign the same on all 12 CO’s 
?..~I 
I I 
l Extension Parameter 
~““““““..““‘- until the EXT...

Description Extension parameters 
Six separate printouts are available. 
They are (1) System parameters (2) CO 
parameters (3) Extensionparameters (4) DSS 
parameters (5) Speed call (6) All parameters aWhen the Proprietary telephone is connected 
at extension. 
Telephone type 
Extension name 
Extension group 
Toll restriction 
Account code input mode 
CO transfer mode 
CO forward mode 
Executive busy override 
Executive busy override deny 
DND override 
Outgoing preference 
Incoming preference 
Line...