Panasonic Kx-T123210 Installation Manual

EIA SIGNALS: 
Frame Ground (FG); 
Connects to the unit frame and the earth ground 
conductor of the AC power cord. 
Transmitted Data (TXD);..................(output) 
Conveys signals from the unit to the printer. A 
“Mark” condition is held unless data or BREAK 
signals are being transmitted. 
Received Data (R)(D);. . . . . . . . . . . . . . . . . . . . . . . .(input) 
Conveys signals from the printer. 
Request To Send (RTS);...................(output) 
This lead is held ON whenever DSR is ON. 
Clear To...

Paging jack 1 
Speaker Use an RCA connector. 
l Output impedance: 
6OOfl 
Amplifier 
Paging equipment 1 
Speaker 
/  Use shielded cable. 
Paging equipment 2 Pa\ging jack 2 
l 
Use a two- 
conductor plug 
(9/64 inch in diameter) 
l Input impedance 
5kfl 
0 Input Level 
-1OdBm 
- 
“‘I ~llllllll~~, 
‘I” ~lllllll1l~, 
;plrrr 
‘I” llllllllllll 
0 
11111l 
0 
!!!!!~llll1 
Please use a 
cord that has 
. . . 
‘I 
EXT MUSIC Jack 
2-20  

PROGRAMMING 
To activate this system, the requirements from telephone company and the customer must be programmed once 
the Power Switch has been turned on. 
1. At extension connected to jack number 01: All system 
4. 
programming changes (example : system clear, 
5. 
toll restriction, system speed dialing entry...) are 
done through extension connected to jack 
number 01. 
l Extension connected to jack number 01 must 
always be a Panasonic model, KX-Tl23230. 
2. System Program Switch setting: 
The...

When the System Program Switch on the KX-T123210 is set to the “PITS” position, the operation of the 
KX-T123230 connected to jack number 01 will change as follows. 
PAUSE button I 
+ button 
Overlay 
 + button CLEAR button 
I--- 
PROGRAMMABLE 
FEATURE button 
- LIQUID CRYSTAL 
Display (LCD) 
CENTRAL OFFICE (CO) 
AUTO/M EMORY button 
PREVIOUS button SELECT button 
FLASH button ICM (SECRET) button 
3-2  

1. Turn the Power Switch to ON. 
2. Set the System Program Switch to “PITS” position. 
The LCD on the KX-T123230 will show “SYS-PGM NO ?-I’. 
o Be sure the handset of the extension connected to jack number 
01 is in the cradle and the speakerphone button off. 
3. To program automatic line access number 9 and the phone 
number 987-654-3210 into speed access code 00. (Refer to 
page 3-5.) 
- 
1 
- 
2 
- 
3 
- 
4 
- 
5 
- 
6 
- 
7 
- 
8 
KX-Tl23230 at extension connected to jack number 01. 
(Extension...

System Feature 
: . . . . . . . . . . . . . . ‘. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._ enter the year with 2 digits. 
18)k/ :1987 year 
I . . .._. _ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
until the 
desired month is 
displayed 
~............................................... 
enter the day with 1 or 2 digits...

AB=mk[ : speed access code 00 
_........................................ 
F[k[ : speed access code 99 
: automatic line access number 
= access number of Trunk Group1 
m%i : access number of Trunk Group8 
or 
,................. 
until the desired speed access code (00 through 99) appears 
lmm(INEXTImIphone number IIMEMoRV(EI 
Description 
100 system phone numbers can be stored with 
each number capable of storing 32 digits and 
may be accessed from any extension. 
Pushing the “ ++‘I, ‘I#” “PAUSE”, “-‘I,...

Conditions 
6. Press the MEMORY button. 
l The memory indicator will be lit. 
7. 
l To advance to the next speed access code, 
press the NEXT button. 
l To return to the previous speed access 
code, press the PREV button. 
l To go to the desired speed access code, 
press the SELECT button and then dial the 
speed access code. 
8. Repeat steps 4 to 7, to program the other 
phone numbers. 
9. To return to the initial program mode, press 
the END button. 
To change 
Repeat steps 1 to 9. 
To erase after...

’ Examples 
1) To enter trunk group access number 81 and telephone number 201-392-4669 into speed access code 00. 
(01 NEXT008; 201-392-4669MEMORYw 
Speed access i Telephone 
code number 
Trunk’group 
access number 
l If punctuation is not entered in a phone number, the LCD will show as below. 
( 00 : 812013924669 ) 
2) To enter automatic line access number 9, account code 1234 and telephone number 201-392-4669 into 
speed access code 02. 
(01 NEXT02 9 * * 1234201-392-4669 MEMORY END) 
--- 7 
: : 
Speed...

l...................until the desired Jack number (01 through 32) appears 
~.......,....................... 
CDE=rI(OI(OI : to assign phone number 100 
111191191: to assign phone number 199 
default 
is assigned to extension of Jack number 01 
132 is assigned to extension of Jack number 32 
,......._.__................................. 
AB=mm : to assign to Jack number 01 
I* : to assign to Jack number 32 
Description 
Enables programming of a 3-digit extension 
number (100 through 199) for each...