Panasonic Kx-T123210 Installation Manual

,.............................- until the desired memory code number (01 through 20) 
appears 
, 
I _ .............................. ..- CDE= exchange code with 3 digits 
Nothing is stored -......-defaul t (all 20 memory codes) 
AB= ml[ : memory code 01 
[?ll: memory code 20 
Description 
The exchange code and area code usually differ 
for local and non-local calls, but in some 
circumstances an area code may be the same as 
a local exchange code. These are important 
when Type B or Type C is selected...

~...-....,.............,....... until the desired memory number (01 through 20) appears 
_ . . . . . . . . . . . . . . . . . . . . 
CDE = area code with 3 digits 
Nothing is stored ‘.....,defauIt (all 20 memory numbers) 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
AB= ml] : memory number 01 for storage of an area code 
memory number 20 for storage of an area code 
Description 
For Service Class 3 (see “Toll Restriction” on 
page 3-li’), up to 20 area codes can be...

,,........,..................... 
A= 111 : to select boundary class I+..... default 
121: class 2 
131: class 3 
q 4 :class4 
151: class 5 
q 6 :class6 
171: class 7 
q : class 8 
Description 
“Toll Restriction”, if it is programmed, prohibits 
CO Operator Calls. However, the desired 
extensions can be permitted to call to CO 
Operator by programming a boundary number 
of service class. 
CO Operator Calls are allowed at all the 
extension from service class 1 to the same 
service class number as the...

,....................... 
until the desired mode appears 
Restriction : will be restricted by a Service Class.........default 
No Restriction: will not be restricted. 
Description 
Through programming, Toll restrictions (service 
classes 1 through 8) set for each extension can 
be applied to speed dialing, too. 
In the “Restriction” mode, Speed dialing is 
restricted by the Service Class. 
In the “No Restriction” mode, Speed dialing is 
not restricted by the Service Class. 
Programming 
1. Dial (12)....

~.............................. until the desired memory number (01 through 20) appears 
: ........................ CDE = exchange code with 3 digits 
Nothing is stored ......... default (all 20 memory numbers) 
I................................... AB=llb]: memory number 01 for storage of exchange code 
memory number 20 for storage of exchange code 
Description 
For Service Class 5 (See “Toll Restriction” on 
page 3-17) up to 20 exchange codes can be 
selected for use in local dialing (charged). 
All...

:‘............................. until the desired memory number (01 through 20) appears 
:........................... 
CDE = exchange code with 3 digits 
Nothing is stored,-....default (all 20 memory numbers) 
i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AB=lO(r/: 
memory number 01 for storage of exchange code 
pi-q 
: memory number 20 for storage of exchange code 
Description 
For Service Class 7 (See “Toll Restriction” on 
page 3-17) up to 20 exchange codes can be...

*.......................................... 
A= 111: to sound after 1 minute 
cl 2 :after 2 minutes 
0: 3 after 3 minutes . . . . . . . ..default 
141 : after 4 minutes 
151 :after 5 minutes 
0 6 : after 6 minutes 
171 : after 7 minutes 
cl 8 :after 8 minutes 
q 9 :after 9 minutes 
Description 
An alarm tone indication will be heard at the 
holding extension to remind the user that he 
still has a call on hold. 
The reminder will sound after 3 minutes but can 
be changed. 
There are 9 choices ranging...

_............................................. I until the desired time appears 
30sec--default 
1 min. 
1.5min. 
2min. 
_ Disable 
Description Example: 
When the handset of the holding extension is 
replaced back on call, you may have the 
automatic hold recall after the desired time 
elapses. 1.5 minutes= 
~INIKFj~ 
jIzGFlMEMoRVI(ENDI 
The hold recall time set can be removed or 
Programming Table 
added at the customer’s request. See page 7-6. 
Programming 
1. 
2. 
3. 
4. 
5. Dial (18). 
“Hold Recall...

until the desired mode appears 
Description Programming 
If a call is transferred to an extension, and the 
other extension does not answer the transferred 
call within 30 seconds, the call will return to you. 
The time may be changed to 15 seconds. 
Refer to “Call Transfer-To Extension” on page 4- 18. 1. 
2. 
3. 
4. 
5. Dial (19). 
“Transfer Recall” will be displayed. 
Press NEXT button. 
“Time: 30 set” will be displayed and the “30” 
will blink. 
Press the SELECT button to alternate between 
“15 set”...

: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . until the desired time appears 
1 ring delay 
2rings delay 
3rings delay _. default 
4rings delay 
Description 
Enables programming the call forwarding 
delayed start time (after 1, 2, 3, or 4 rings) in 
case of no receiving the call when the “Call 
Forwarding-Busy or No Answer” (on page 4-26) 
feature is set. 
Programming 
1. Dial (20). 
“Call FWD Delay” will be displayed. 
2. Press the NEXT button. 
“3 rings delay” will be...