Panasonic Kx-T123210 Installation Manual

until the desired mode appears 
Description 
Outside calls can be transferred to any 
extension manually. 
Programming Table 
See page 7-3. 
l While an extension paired with the DSS 
Console having a conversation with outside 
calls, “With Transfer” mode allows you to 
transfer outside call by only pressing the DSS 
button of the DSS Console. 
l While an extension paired with the DSS Console 
having a conversation with outside calls, “Without 
Transfer” mode allows you to transfer outside call 
by...

_ .......................... until the desired mode appears 
Man ......... Day/Night service is manually switched ....... default 
Auto ......... Day/Night service is automatically switched 
Description 
Allows Day/ Night service to be selected 
manually or automatically. 
In case of manual switching, refer to “Flexible 
Night Service” on page 4-37. 
In case of automatic switching, set the “Starting 
Time (Day/Night Service mode)” on page 3-13. 
The following features will be switched 
Day mode or Night...

AB= 111 
: to start at 1 o’clock for day service 
191 : to start at 9 o’clock for day service . . . . . . . ..default 
p$!-j : to start at 12 o’clock for day service 
L 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
CD=m,E[ : to start at 0 rninute.........................default 
jT/i-Gl : to start at 59 minutes 
:....“““.‘. until the desired mode awears 
AM . . . . . . 
. . . . . . . . . . . . . . . . . . . iifaul* 
PM 
EF= m 
: to start at 1 o’clock for night service 
m : to start at...

Description 
If you select the automatic switching mode for 
day/night service, enter the starting time. 
Refer to “Switching of Service Mode (Day/Night 
Service Mode)” on page 3-12. 
Programming 
1. Dial (07). 
“Day/Night Time” will be displayed. 
2. Press the NEXT button. 
“Day: 9:00 AM” will be displayed as a default 
value and “9” will blink. 
3. Enter the starting time for day service using 1 
or 2 digits. 
4. Press the “ +” button 
“00” will blink. 
5. Enter the minutes using 2 digits. 
6. Press...

i,.......................-until the desired extension group number (1 through 8) appears 
until the desired mode appears 
i ~............................~ 
Description 
Enables programming to automatically locate 
an idle extension within the same extension 
group as the dialed extension when the 
dialed extension number is busy. 
Call Hunting is set by group units. “Extension 
Group Assignment” (on page 3-63) is used to 
specify which extensions belong to the each 
group. 
Programming 
Dial (08)....

j........-.......until the desired extension group number (1 through 8) appears. 
;.. until the desired hunting type appears 
Terminate : searching for larger jack numbers upward ..... default (all 8 groups) 
Circular : circular searching for other numbers 
:........,...................... A=B : to assign the same of all 8 extension groups 
q : extension group 1 
I 0 8 : extension group 8 
Discription 
Specifies the order in which idle extensions 
are searched when “Call Hunting” is used. 
The “Terminate...

type A . . . . . . . . . . default 
Description 
Area types specific to local telephone numbers can be selected for toll restrictions. 
There are three area types available as shown below. 
Type A : Toll calls (long distance) Area code Exchange code 
Local calls .................................. 
Exchange code Subscriber number 
Type B : Toll calls (long distance) ........... Area code 
Local calls .................................. 
Exchange code 
Type C : Toll calls (long distance) .......... 
1 -...