Panasonic Kx Ncp500/1000, Kx Tde100/200, Kx Tde600 Operating Manual

Fixed Buttons
Function
KX-NT300/
KX-NT500/
KX-DT300 KX-NT136/
KX-T7600 KX-T7200/KX-T7400
*1 NEXT
STORE (ENTER)
None
Back to Previous Menu 
(CANCEL) SHIFT
PROGRAM
END
SELECT
FLASH
CLEAR
SECRET
*1
The buttons shown in this column are from  KX-T7400 series PTs. Procedure
The basic steps are shown below. Document Version  2013-05  
Operating Manual 201 3.3.1 Programming Information    SP-PHONE   FWD/DND    CONF    AUTO DIAL
STORE   SHIFT SHIFT SHIFT PAUSE PAUSE PROGRAMPAUSE  HOLD HOLD  AUTO ANS
MUTE
MESSAGE...

1.
Entering the programming mode 2.
Programming
You can enter each program number 
(3 digits).•
To exit the programming mode at any time,  lift the handset.
3. Exiting the mode •
To exit the programming mode at any time,  lift the handset.202 Operating Manual
Document Version  2013-05  3.3.1 Programming InformationEnter system password. Enter        . 
system password
Press PROGRAM
or PAUSE.
OR
PROGRAM
PAUSE  Press PROGRAM
or PAUSE.
OR
PROGRAM
PAUSE   

3.3.2  System Programming
 [000] Date & Time
The proprietary telephones display the current date and time while on -hook.•
After changing the desired values,  you can press the ENTER button. You do not have to
perform the rest of the steps.
• The clock starts immediately after the ENTER button is pressed.
• You cannot leave a value empty.
• You can clear the entry by pressing the CLEAR button.
• To confirm your entry after storing data:
–The STORE button light: Lights red
– Confirmation Tone:
One beep:...

 [001] System Speed Dialing Number
You can store the phone numbers of frequently dialed numbers. •
If the desired number is more than 32 digits, divide the number and store it into more than
one speed dialing number.
• " ", "#", FLASH/RECALL, PAUSE, and Secret (INTERCOM) can also be stored.
If you do not want to display the stored number when making a call, press the Secret 
(INTERCOM) button before and after the numbers you wish to conceal.
If you store an outside party’s number, you...

 [002] System Speed Dialing Name
You  can store the name associated with the speed dialing number. These names are displayed when making
calls using the display operation. To enter characters, refer to  "1.3.14  Character Entry". [003] Extension Number
You can assign an extension number to each extension. •
The leading number
 (s) should be the same as the number(s) assigned for Flexible
Numbering.
• A duplicate entry is invalid.  [004] Extension Name
You 
 can store the name of an extension...

To enter characters, refer to "1.3.14  Character Entry".
206 Operating Manual
Document Version  2013-05  3.3.2 System ProgrammingPress ENTER. Enter 004. Press ENTER. Press END.
Press CANCEL. Press NEXT. Press PREV.
To continue
To end
004
Enter extension 
number.
extension no.
Enter name
(max. 20 
characters).name
OR  

Section  4
Appendix
This chapter provides the Troubleshooting, the Feature
Number Table and Tone List. Check the
Troubleshooting section before consulting your dealer. Document Version  2013-05  
Operating Manual 207 

4.1  Troubleshooting
4.1.1  Troubleshooting
 Troubleshooting
Problem Remedy
The telephone does not work properly. •  Confirm with your manager that your settings are
correct.
•  If the problem persists, consult your dealer.
The telephone does not respond when
buttons are pressed. •
The telephone is locked.  Unlock your telephone. (  1.3.25  Extension
Dial Lock, 2.1.5  Remote Extension Dial Lock )
• Your telephone is connected to an eXtra Device
Port.  System programming is required. Consult your
dealer....

Problem
Remedy
A reorder tone is audible or "Restricted"  is
displayed. •
The telephone is locked.  Unlock your telephone. (  1.3.25  Extension
Dial Lock, 2.1.5  Remote Extension Dial Lock
 )
• Toll restriction is activated.  Consult your manager or dealer.
• An account code is required.  (  1.3.2  Account
Code Entry, 1.3.68  Verification Code Entry
 ,
1.3.74  Walking COS)
I cannot make an outside call using the
One-touch 
 Dialing button or speed dialing. •
A line access number was not stored....

Problem
Remedy
I cannot send a call waiting tone to the
dialed extension. •
The other party has not set the Call Waiting feature.
(  1.3.13  Call Waiting Tone, 1.3.46  OHCA
(Off-hook Call Announcement)
 , 1.3.77  Whisper
OHCA)
• The other party has set Data Line Security.
(  1.3.18  Data Line Security)
I forgot the password. •Ask the manager to assist you.
(  2.1.1  Dial Tone Transfer)
The background music started suddenly. •  Turn off the music.
(  1.3.5 
 BGM (Background Music), 2.1.2  External
BGM...