Panasonic Disk Recorder Management Software Wv As65 Operating Instructions

							51
Edit the name of the registered favorite
Step 1
Right click the desired icon to be edited and select
Rename(R) from the right click pop-up menu.
The selected favorite name will be highlighted and can
be edited.Step 2
Enter the new name for the favorite and press the
enter key of the keyboard.
The newly entered favorite name will be registered.
Note:
Enter up to 32 alphanumeric characters.
The following characters are not available (\, /, :, *,
?, , , |).
Delete the registered favorite
Step 1
Right click the desired icon to be edited and select
Delete(D)… from the right click pop-up menu.
The deletion confirmation window will be displayed.Step 2
Click the [Yes] button.
The selected favorite will be deleted.
Note:
It may take a while when trying to delete a number
of favorites at one time. 
						

							52
Step 3
Click the [PLAY] button.
The recorded images of the selected camera channel
will be played. (The icon on the status bar indicating
that live images are being displayed will change to the
icon indicating that recorded images are being dis-
played.)
When displaying images on a single screen, refresh
interval of recorded images can be selected. Right-
click on the image currently being played and change
the value of Video Rate(I).
Note:
When the [PLAY] button is clicked, the latest
recorded images will be played.
HD300
Play Recorded Images on the Recorder
Step 1
Display live images.
When displaying live images on a multi-screen, click
the desired area (camera channel). The clicked area
will be displayed with an orange frame.
Step 2
Click the [RECORDER] control tab.
The recorder control panel will be displayed.
Notes:
•Playback speed may become slow when load to be processed for the recorder or the PC is getting higher (such
when many cameras are connected or when live/recorded images are displayed on multiple windows).
•When the [NEXT IMAGE] button is repeatedly clicked, it may skip frames reversely and a frame of at a point sev-
eral seconds before the point where the [NEXT IMAGE] button is clicked may be displayed.
•When displaying images on a multi-screen, it may cause out-of-sync between each channel.  
						

							53

Step 4
Click the [STOP] button.
Playback of the recorded images will be changed to
live images. (The icon on the status bar indicating that
recorded images are being displayed will change to
the icon indicating that live images are being dis-
played.)
Note:
Operate during playback using buttons on the
recorder control panel.
Refer to page 33 for descriptions about the buttons
on the recorder control panel.
When controlling the recorded images of one cam-
era channel during the playback of recorded
images of multiple camera channels of the same
recorder, the recorded time of all the recorded
images of the other camera channels that are cur-
rently being played will be synchronized with the
recorded time of the recorded images of the select-
ed camera channel. The areas displaying recorded
images with the synchronized recorded time will be
displayed with a pale orange frame.
d 
						

							54
Search and Play Recorded Images
Search for the desired recorded images using any of
the following four methods.
Notes:
•Up to 10 000 recorded images can be searched.
When more than 10 000 recorded images are
found, a message window will be displayed. In this
case, search again with more detailed conditions.
•Up to 1 024 recorded images per a recorder can be
searched. When more than 1 024 recorded images
are found on a single recorder, a list of the latest
1 024 recorded images will be displayed in the
search result list window.
•It may take 10 minutes or more to complete
searching.
Search for a Recording Event
Search for the desired images with such parameters
as the date-and-time, the camera channel and the type
of events. (REC Event Search)
Step 1
Display the operation window in the network mode.
Step 2 
Select Search(S)... from Search(S) on the menu
bar.
The search window will be displayed.
Step 3
Click the [REC Event Search] tab.
qw
er
t
qRecorder & Camera(R)
Designate the desired recorder and the camera
channels to be searched.
wFROM(F)
Designate the start time of the time range to be
searched.
eTO(T)
Designate the end time of the time range to be
searched.
rREC Event(E)
Designate the recording event type to be searched
by checking the box next to the desired recording
event type.
CAM(C) :Recording performed when a
(camera) site alarm has been detected
VMD(V) :Recording performed when
motion has been detected
TERMINAL(M):Recording performed when a
terminal alarm has been detected
COMMAND(O):Recording performed when a
command alarm has been detected
VIDEO LOSS(L)  :Recording performed
when video loss has occurred
EMERGENCY(G):Emergency recording
MANUAL(A):Manual recording
SCHEDULE(H):Schedule recording
tText(X)
Search for only images recorded with or without
text information.
y[Search(S)…] button
Click this button to start searching with the selected
conditions.
u[Cancel] button
Click this button to cancel search with the selected
conditions and close the search window.
HD300
HD300
ND300
yu 
						

							55
Step 4
After designating the search conditions, click the
[Search(S)...] button.
The search status window will be displayed. The name
of the recorder to be searched will be displayed in the
result list. The check mark will be displayed next to the
name of the recorder to indicate that the search of the
recorder has finished.
When the check mark is displayed next to all the
recorders respectively, the search is complete.
qRecorder list
The recorder names to be searched are listed.
Search complete check:The check mark will be
displayed next to the name of the recorder to
indicate that the search of the recorder has fin-
ished.
Search result:The number of search result will be
displayed.
Status:The current status of search will be dis-
played.
w[Search list view(S)] button
When searching is completed, the button will be
operable. Click this button to display the search
results.
e[Cancel] button
Click this button to cancel searching and return to
the window where search conditions are set up.
Step 5
Click the [Search list view(S)] button.
The search result list window will be displayed.
Notes:
•About the search results
When 0 is displayed in the result column, no
recorded image was found with the selected condi-
tions.
When Search failed is displayed in the result col-
umn, the search failed. Check whether the recorder
is connected and located in the registered IP
address or the host name by performing the con-
nection test.
•When more than 10 000 recorded images are
found, a message window will be displayed. In this
case, search again with more detailed conditions.
•When searching for an event type that is not select-
ed, 0 will be displayed in the result column.
Searched countd
e w q
Note:
Channels of which the Model number setting is --
 will not be displayed in Recorder & Camera.
ND300 
						

							56
Search for a motion detected time and date from recorded
images 
Search for a motion detected time and date from all the images recorded in the designated recorder. (VMD Search)
It is impossible to designate two or more recorders  two or more camera channels.
HD300
Step 1
Display the operation window in the network mode.
Step 2
Select Search(S)... from Search(S) on the menu
bar.
The search window will be displayed.
Step 3
Click the [VMD Search] tab.qRecorder(R)
Designate the desired recorder to be searched.
wCamera(C)
Designate the camera channel to be searched.
eFROM(F)
Designate the start time of the time range to be
searched.
rTO(T)
Designate the end time of the time range to be
searched.
t[VMD area setup(V)…] button
Click this button to display the VMD area setup
window.
y[Search(S)…] button
Click this button to start searching with the selected
conditions.
u[Cancel] button
Click this button to cancel search with the selected
conditions and close the search window.
Step 4
Designate the search conditions.
q
w
e
r
t
yu 
						

							57
Step 5
When it is necessary to set the VMD areas, click the
[VMD area setup(V)…] button to display the VMD
setup window.
When the VMD areas have already been set, go to
step 9.
Note:
The VMD areas are registered for the respective
camera channel of each recorder.
Step 6
The VMD area setup window will be displayed.
Perform the following settings:
qRecorder title and Camera title
The name of the selected recorder and the camera
channel number to be searched will be displayed.
wVMD area setup display
A still image from the selected camera channel will
be displayed. Set the VMD area in this display
area.
eDeletion checkbox
Select the desired VMD area to be deleted by
checking the box next to the desired VMD area.
r[DELETE AREA(D)] button
Click this button after checking the box next to the
desired VMD area to be deleted.
tSensitivity(S)
Select the sensitivity for each VMD area from the
following: 
HIGH:High sensitivity
MID:Middle sensitivity
LOW:Low sensitivity
OFF:Ignores motion in the selected area
The default setting is OFF for each area.
yVMD mode
Select the VMD mode to be searched from the fol-
lowing: The default setting is ANY AREA.
ANY AREA(A)
uMask period(M)
Select a masking duration from the following:
1s/ 1min/1h/24h (The default setting is 1s for
each area.)
VECTOR(V)
iVMD area order
Select an order of the VMD areas.
oDetection time of vector mode
Select the duration of motion detection between
two VMD areas.
DURATION(U)
!0Detection time of duration mode
Select a detection time for each area.
!1[OK] button
Click this button to save the settings for the VMD
areas.
!2[Cancel] button
Click this button to cancel to save the settings and
close the VMD setup window.
q
we
r
u
y
t
i
o
!0
!1!2 
						

							58
Step 7
Perform the VMD area setup and detection parameter
setup.
VMD area setup
Set the motion detection areas by dragging the cur-
sor. Up to 4 areas (A, B, C, D) can be set for the
detection areas.
A: White, B: Blue, C: Green, D: Red
To delete a detection area, click the [DELETE
AREA(D)] button after selecting a detection area by
checking the box of the desired area to be deleted.
Sensitivity(S)
Select the sensitivity for each VMD area from the
following: Click the  button to select sensitivity
for the selected area from the following.
HIGH:High sensitivity
MID:Middle sensitivity
LOW:Low sensitivity
OFF:Ignores motion in the selected area
VMD mode setup
Perform the settings for the detection mode. It is
possible to set how motion is detected in the
motion detection area by performing the settings
for each detection mode.
Select the desired detection mode and perform the
settings by checking/not checking the radio but-
tons.
•
An event action will be performed according to
the settings when motion is detected in any of
the set motion detection areas.
•
Click the  button to create a series of VMD
areas in the desired order. Click the  button
to select a moving duration for an object from
the following.
--/5s/10s/20s/30s/40s/50s/1min

Click the  button to select a detection time
for each area.
0s/5s/10s/20s/30s/40s/50s/1minNote:
Refer to the Network Operating Instructions (PDF)
of the recorder for further information about the
VMD search.
Step 8
Click the [OK] button to save the settings for the VMD
areas.
The VMD setup window displayed on the search win-
dow will be closed.
Step 9
Click the [Search(S)...] button.
The search status window will be displayed.
Note:
When the VMD area is not yet set, a message win-
dow will be displayed.
Go to step 4 to set the VMD area.
Step 10
Click the [Search list view(S)] button.
The search result list window will be displayed.
Refer to page 61 for descriptions of how to operate on
the search result list window. 
						

							59
Search for a marked point 
Search for the point marked during playback the recorded images. (Marking Search)
HD300
Step 1
Display the operation window in the network mode.
Step 2
Select Search(S)... from Search(S) on the menu
bar .
The search window will be displayed.
Step 3
Click the [Marking Search] tab.w[Search(S)…] button
Click this button to start searching with the selected
conditions.
e[Cancel] button
Click this button to cancel search with the selected
conditions and close the search window.
Step 4
Designate the desired recorder subject to search.
Step 5 
Click the [Search(S)...] button.
The search status window will be displayed.
Step 6
Click the [Search list view(S)] button.
The search result list window will be displayed.
Refer to page 61 for descriptions of how to operate the
search result list window.
q
qRecorder(R)
Designate the desired recorder to be searched.
we 
						

							60
Search for images saved on the SD memory card on the camera
(SD memory data)
It is possible to search for SD memory data (images saved on the SD memory card on the camera). (SD search)
To search for SD memory data, designate a single recorder and a single camera channel. It is impossible to desig-
nate multiple recorders or multiple channels.
ND300
Step 1
Display the operation window in the network mode.
Step 2
Select Search(S)… from Search(S) on the menu
bar.
The search window will be displayed.
Step 3
Click the [SD search] tab.qRecorder(R)
Designate a recorder to be searched.
wCamera(C)
Designate a camera channel to be searched.
eFROM(F)
Designate the start time of the time range to be
searched.
rTO(T)
Designate the end time of the time range to be
searched.
t[Search(S)…] button
Click this button to start searching with the selected
conditions.
y[Cancel] button
Click this button to cancel search with the selected
conditions and close the search window.
Step 4
After designating the search conditions, click the
[Search(S)…] button.
The search status window will be displayed.
Step 5
When the search is completed, click the [Search list
view(S)] button.
The search result list window will be displayed.
Refer to page 61 for how to operate the search result
list window.
q
w
e
r
ty