Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide

71
Configure	the	settings	relating	to	event	[Event]
The settings relating to event actions of each event type (terminal alarm, video moti\
on detection (VMD), video loss, and camera 
alarm site) can be configured on the "Event" page. 
Details on how to operate this page are given on Operating Instructions (PDF). 
The "Event" page has [Common], [Terminal/Command], [Site alarm], [Video loss] and [VMD] tabs. 
Configure	the	common	settings	for	event	actions	[Common]
Select the [Common] tab on...

72
[Operation	mode]
Select the settings for the operation mode.
Refer to the operating instructions (PDF) for further informa-
tion about the operation mode.ADM	(Activity	Detection	Mode): Performs recording, writes the event log, and moves the cameras to pre-
set positions at an event occurrence.
  Other event actions will not be performed.
ALM	(Alarm	Mode): Performs every event action  according to the settings.
Off: Performs only writing an event log. Other event  actions will no be performed....

73
Configure the event action at a camera site alarm occurrence [Site 
alarm]
Select the [Site alarm] tab on the "Event" page. (+ Page 60)
The settings relating to event actions to be taken at a camera site alarm (+ Operating Instructions (PDF)) occurrence can be con-
figured on this tab.
    
[Operation	mode]
Select the settings for the operation mode. Refer to the 
operating instructions (PDF) for further information about the 
operation mode. ADM	(Activity	Detection	Mode): Performs recording,...

74
Configure	the	event	action	at	a	video	loss	occurrence	[Video	loss]
Select the [Video loss] tab on the "Event" page. (+ Page 60)
The settings relating to event actions to be taken at a video loss (+ Operating Instructions (PDF)) occurrence can be configured 
on this tab. 
    
[Operation	mode]
Select the settings for the operation mode.
Refer to the operating instructions (PDF) for further informa-
tion about the operation mode.ADM	(Activity	Detection	Mode): Performs recording, writes the event...

75
Configure	the	event	action	at	a	VMD	occurrence	[VMD]
Select the [VMD] tab on the "Event" page. (+ Page 60)
The settings relating to event actions to be taken at a VMD (+ Operating Instructions (PDF)) occurrence can be configured on 
this tab.
    
[Operation	Mode]
Select the settings for the operation mode. Refer to the 
operating instructions (PDF) for further information about the 
operation mode.ADM	(Activity	Detection	Mode): Performs only recording and writing an event log at an event...

76
[Search]
Select "On" or "Off" to determine whether or not to perform 
video motion detection.
When "Off" is selected, video motion detection will not be 
performed. When "On" is selected, VMD (video motion 
detection) areas can be set.
Up to 4 areas can be set for a camera channel for the detec-
tion area.Details on video motion detection are given on 
Operating Instructions (PDF).
[Area]	button
Configure the settings for each camera channel (1 to 16).  
(+ Page 77)
     

77
Step 1
Select the [Area/Sensitivity] tab and select the [Setup] button 
of one of the detection areas (A to D).
  →  A detection area setup page will open.
Note:
	 •	 When	selecting	the	[All	area]	button,	all	the	area	on	the	 displayed image can be set as the detection area.
 
    Step 2
Set the start point of the detection area. 
Press the [SET] button after moving the cursor to the desired 
start point of the detection area using the arrows button (C 
D A B). When using a mouse, click the start...

78
Step 3
Set the end point of the detection area. 
Press the [SET] button after moving the cursor to the desired 
end point of the detection area using the arrows button (C 
D A B). To finish the detection area setting, select the 
[Back] button.
Note:
	 •	 Detection	areas	will	be	set	according	to	the	grid	divided	 in 16 x 14 segments. It may be possible that the actual 
detection areas will not be exactly the same as the des-
ignated start and end points.
	 •	 To	delete	a	set	detection	area,	select	the...

79
Configure	the	settings	relating	to	recording/event	schedules	
[Schedule]
The settings for the recording schedules and event actions are performed on the "Schedule" page by designating a day of the 
week and time. 
It is possible to create a time table by dividing a day into up to 6 time zones and to create recording schedules by assigning pro-
grams to the created time zones and by setting "On" or "Off" for each event action. 
Up to 4 programs can be created for the recorder....

80
[Resolution]
Select a resolution for images to be recorded. Field: Standard resolution (704 x 240)
Frame 3D On: High resolution (704 x 480) with the motion blur compensation function
Frame 3D Off: High resolution (704 x 480)
Default: Field
[Maximum	REC	rate]	(Only	for	HD716K)
Select the maximum recording rate that is available for each 
channel. 
The available values vary depending on the setting of 
"Resolution". 
	 •	 When	"Frame	3D	On"	or	"Frame	3D	Off"	is	set	for...