Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide

111
Change or delete the host information
Change or delete the host information that has been registered. 
    
Step 1
Select the [Edit/delete] button on the [Host] tab. 
  →  The "Host edit" page will be displayed. 
Step 2
Select the "Host IP address" of the host to change or delete 
the host information. 
  →  The host information of the selected host will be dis-
played. 
Note:
	 •	 Select	the	[Back]	button	to	return	to	the	screen	to	regis- ter a user.
    Step 3
To change the host...

112
Setting	of	operation	level	[User	level]
Select the [User level] tab on the "User mng." page. (+ Page 60)
A level (LV 2/LV 3) can be assigned to every user to restrict operable functions on this tab. To forbid user to operate, leave it 
blank. It is impossible to change the setting for LV1.
Refer to the diagram for further information about each function. 
    
Note:
	 •	 Available	functions	for	each	user	level	are	as	follows: LV1: Possible to perform all the operations (Administrators)
LV2:...

113
The settings relating to the intelligent video motion detection function (hereinafter, i-VMD) of SD5Link cameras connected to the 
recorder can be configured on the "SD5Link" page. It is possible to upload the settings to SD5Li\
nk cameras and download the 
settings to the recorder.
The "SD5Link" page has [i-VMD setup] and [Setup data] tabs.
To configure the settings for the SD5Link function, it is necessary to select "COAX\
" for "Type" of the camera channels to which...

114
Setting the detection areas and sensitivity
Step 1
Select the [Setup] button of the [i-VMD setup] tab. 
  →  The setup page for camera's i-VMD function will be dis-
played. 
Note:
	 •	 When	no	operation	is	made	for	approx.5	minutes	on	the	 setup page for camera's i-VMD function, the display will 
automatically return to Step 1.
Step 2
Select the desired camera. 
Select the [Cam.1] tab, and then select the desired camera 
(Cam.1/Cam.2...Cam.16) from the pull-down menu. 
    
Step 3
Select the...

115
Step 5
Set the start point of the detection area. 
Move the cursor to the desired start point, and click the 
mouse button. 
Step 6
Set the end point of the detection area.
Move the cursor to the desired end point, and click the 
mouse button. To determine the detection area, select the 
[Back] button.
Note:
	 •	 Detection	areas	will	be	set	according	to	the	grid	for	the	 detection areas of the SD5 camera. It may be possible 
that the actual detection areas will not be exactly the 
same as the...

116
Setting the scene change
Select "On" or "Off " to determine whether to provide an alarm signal when a change in the state of scene occurs by cove\
ring the 
camera with a cloth, a cap, or others, or by changing the camera direction largely. 
Setting the detection mode
Set the detection conditions for "Motion det." and "Object det.". In add\
ition, determine whether or not to display the frames of 
detection areas on the screen. 
    
Step 1
Display the setup page for...

117
Setting the detection depth
Set the detection depth of the detected areas. By setting the detection depth, it is possible to automatically cal\
culate the size of 
object to be detected on the screen to reduce the detection failure. 
To calculate the detection depth properly, mount the camera horizontally.
    
Step 1
Display the setup page for camera's i-VMD function, and 
select the desired camera and scene. (+ Page 114)
Step 2
Select the [Detection depth] tab. 
  →  The [Detection depth] tab...

118
Uploading or downloading the settings of SD5Link cameras [Setup 
data]
Select the [Setup data] tab on the "SD5Link" page. (+ Page 60)
It is possible to retrieve setup data of an SD5Link camera and to load the retrieved data to the SD5Link camera.
    
[Setup	data]
The setup data downloaded from SD5Link cameras are dis-
played. 
Displays the model numbers of the cameras and time & date 
when setup data are downloaded. "-" is displayed when the 
setup data are not downloaded. 
[Select]...

119
The version of the recorder and disk information is displayed, and the settings relating to hard disk drives can be configured on 
the "Maintenance" page. It is also possible to initialize the setup data\
 of the setup pages, format SD memory cards, and check 
the system logs on this page. 
The "Maintenance" page has [Product information], [Disk information], [Network information], [Disk], [\
Settings management] and 
[Logs] tabs. 
Check the product information such as the version...

120
[Recording	information]
When the [Display] button is selected, the "Recording infor-
mation" page will be displayed, and the disk capacity and 
the available capacity of each hard disk drive, the hour meter 
and the time range of the images recorded on each hard 
disk drive will be displayed. 
There are 2 setup pages. To move to another page, select 
the [] button.Note:
	 •	 Information	is	displayed	on	"HDD1"	in	the	RAID5	or	 RAID6 mode. 
[Main]	button/[Ext.1]	-	[Ext.3]	buttons
Select...