Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide

21
How to detach the front cover
Step 1
(When detaching the front cover while the power is on)
Hold down the [ALARM RESET] button and the [MONITOR] 
button (for more than 2 seconds).
  →  The power of the front cover will be turned off.
Step 2
Open the maintenance port cover and the DVD drive cover, 
and then remove the fixing screws (x3).
Step 3
Pull the right side of the front cover first, and then detach the 
front cover.
Step 4
Disconnect the connection cable of the front cover.
	 •	 Detach	the...

22
Note:
	 •	 After	attaching	the	front	cover	to	the	recorder,	be	sure	to	 turn on the power of front cover.
 
■  Rear view
    
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
ALARM/CONTROL
VIDEO
OUT
-CASCADE-IN CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
q w e r t y u
!2 !3 !4 !5 !6 !7 !8!1
i
!0
o
 q	 Alarm/Control...

23
 !4	 Monitor	output	connector	(BNC)	[MONITOR	OUT	 
1,	2]
    Connect a monitor to this connector. Monitor output 
connector 1 shall be used to connect a monitor (Monitor 
1) to display live image only. Monitor output connector 2 
shall be used to connect a monitor (Monitor 2) to display 
live/recorded images and the setup menus. Monitor out-
put connector 2 can also be used for cascade output.
  !5	 Cascade	input	connector	(BNC/HDMI)	[CASCADE	
IN	1,	2]
    Connect the other recorder in cascading...

24
User/Host	management
It is necessary to register users who operates the recorder and hosts (PC) that accesses the recorder via a network such as a 
LAN. Up to 32 users and up to 8 hosts can be registered.
The following information can be registered as user information and host information.
ItemDescription Remarks
User name User name is to be registered to log in to the recorder.  
It will be required to log in to the recorder. This setting item can be configured only in 
the user registration.
IP...

25
Note:
	 •	 When	operating	from	a	system	controller	compatible	with	PS·Data,	log	in	to	the	recorder	automatically	as	the	user	registered	 in "PSD user" on the "Basic" tab under "User mng.".
	 •	 When	no	operation	is	made	for	approx.2	minutes	after	logging	in	from	a	system	controller	compatible	with	PS·Data,	the	PSD	 user will automatically be logged out.
	 •	 When	trying	to	log	in	as	the	same	user	name	used	by	a	user	who	is	already	logged	in,	both	users	will	be	authorized	to	log...

26
To directly operate the recorder, there are 2 ways of how to operate it: operations using the buttons on the front cover and opera-
tions using a mouse connected to the recorder.
Basic operation
Operations using a mouse
The recorder can be operated using a mouse connected to 
the mouse port on the front cover.
Move the mouse cursor onto a button or a tab on the screen 
of Monitor 2, and then click on it
When right-clicking, the operation panel representing the 
front cover (the monitor operation...

27
➜
Operations flow
The operation flow of the recorder is as follows.
    
Rack mounting (+ Page 28)z
➜
Connections (+ Page 29)x
➜
Installation of the hard disk drives  
(+ Page 52)c
➜
Determination of the operational mode
(+ Page 54)v
➜
Startup (+ Page 55)b
➜
Configuration of the settings for the  quick setup. 
(+ Page 63)n
	z Install the recorder in the rack.
    Go to step x when not installing it in the rack.
    
	x  Connect the recorder to each device.
    When using an optional extension unit,...

28
Rack mounting
Install the recorder in an EIA standard rack.
Equivalent to EIA standard rack (not manufactured by Panasonic): EIA 19-inch rack type (Depth: 550 mm or more)Note:
	 •	 Use	four	M5	x	12	screws	(locally	procured)	to	install	the	recorder	in	a	rack.
 
    
Step 1
Remove the five rubber feet from the bottom of the recorder 
using a flathead screwdriver. 
Use a screwdriver to remove the screws holding the rubber 
feet.
Step 2
Attach the rack handles to the rack mount brackets.
Fix them firmly...

29
Connection of cameras
Up to 16 cameras (system cameras or combination cameras) can be connec\
ted to the video input connector 1-16.Important:
	 •	 When	using	with	a	Panasonic's	matrix	switcher	or	a	coaxial	communication	unit,	make	sure	that	the	loop-through	output	 connection	(of	each	video	input)	to	the	recorder	are	correctly	made.	When	a	monitor	output	or	a	spot	output	is	connected	to	
the	video	input	connector	of	the	recorder,	noise	may	be	produced	upon	switching	camera	channels	or	images	of...

30
Connection of monitors
Connect monitors to the monitor output connector.
Connect a monitor to be used to display live images only to the monitor \
output connector 1.
Connect a monitor to be used to display not only live images but also recorded images and setup menu to the monitor output 
connector 2.
The monitor can be connected using a BNC cable or a HDMI cable. (There is no difference in contents to be output to each 
monitor.)
When connecting a monitor using a BNC cable
    
EXT STORAGEMODE
D...