Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide

11
Network security
As you will use this product connected to a network, your attention is called to the following \
security risks.
 q  Leakage or theft of information through this product
  w  Use of this product for illegal operations by persons with malicious intent
  e  Interference with or stoppage of this product by persons with malicious intent
It is your responsibility to take precautions such as those described below to protect yourself against the above network security 
risks.
	 •	 Use	this...

12
Power source
The input power source for this product is 120 V AC, 60 Hz. 
Do not connect to the outlet that provides the power to 
equipments that requires a measurable amount of power 
(such as a copy machine, air conditioner, etc.). Avoid placing 
this product in locations where is subject to water.
Ambient operating temperature
Use this product at temperatures between +5 °C to +45 °C 
{+41 °F to +113 °F}. Failure to do so may damage the inter-
nal parts or cause malfunction. Performance and...

13
Cleaning
	 •	 Turn	the	power	off,	and	then	use	a	soft	cloth	to	clean	this product. When the dirt is hard to remove, use a mild 
detergent and wipe gently. Wipe out the detergent com-
pletely using a soft cloth.
	 •	 Do	not	use	strong	or	abrasive	detergents	when	cleaning	 the body.
	 •	 When	using	a	chemical	cloth	for	cleaning,	read	the	cau- tion provided with the chemical cloth product.
Indication label
Refer to the indication label placed on the surface of this 
product as to the indications of...

14
Precautions for Installation
This product is designed for indoor use.
Avoid the following locations for installation.
	 •	 Locations	exposed	to	direct	sunlight
	 •	 Places	subject	to	having	strong	vibration	or	impact
	 •	 Near	magnetic	field	sources	such	as	a	television	or	speakers
	 •	 Place	where	condensation	forms	easily,	where	tempera- ture changes greatly, humid places
	 •	 Steamy	and	oily	places	such	as	kitchens
	 •	 Places	which	are	not	level
	 •	 Places	subject	to	dust
	 •	 Places	subject	to...

15
For BNC cable connection
Use only the recommended plug below when connecting the 
BNC plug to the connectors on the rear panel of the record-
er. 
Applicable plug: MIL-C39012C or MIL-C39012/16F
 * Suffixes attached to the standards may be updated. 
Tip dimensions inside the recommended BNC plug
Important:
	 •	 A	compatible	plug	shall	be	used.	Failure	to	observe	this	 may cause trouble such as poor contact. At worst, the 
connector of this product may be damaged. 
 
Avoid placing receptacles that...

16
Major	operating	controls	and	their	functions
■ Front view
 q  Status indicator
ERROR: Blinks when an error that can become a prob-
lem for the recorder to run the system occurs.
Blinks red: System error
Blinks orange: Thermal error, cooling fan malfunc-tion, etc.
ALARM: Blinks when an alarm occurs, and lights when  the alarm output stops. The blinking or lighting indi-
cator will go off when the alarm reset button is 
pressed.
ALARM SUSPEND: Lights when the alarm suspension  mode is selected. (+...

17
 u	 Maintenance	port
    The maintenance port that can be used for connection 
with a PC is provided inside the cover. Do not use for 
any operation other than maintenance.
  i	 HDD	indicator	[HDD1	to	HDD4]
STS (status): Indicates the operational statuses of the  respective hard disk drive.
Lights green: Indicates that the power of the respective hard disk drive (formatted) is on.
Blinks green: Indicates that the respective hard disk  drive is for playback use only. (Recording is 
unavailable using...

18
Insert	an	optional	SDHC/SD	memory	card
Step 1
Open the SDHC/SD memory card slot.
Step 2
Insert a SDHC/SD memory card to the slot until it clicks.
Step 3
Close the cover of the SDHC/SD memory card slot.
Note:
	 •	 When	removing	the	SDHC/SD	memory	card	from	the	 slot, push the card until it clicks and pull it up straight.
 
    
Insert	a	DVD	disc	(commercially	available)
Step 1
Open the DVD drive cover.
Step 2
After confirming that the power of the recorder is on, press 
the eject button located at the...

19
Step 4
Push the tray to the end. Click sound will be heard and the 
tray will be fixed.
Step 5
Close the DVD drive cover.
Important:
	 •	 When	opening/closing	the	DVD	drive	tray,	do	not	apply	 force on the tray. 
	 •	 When	not	using	the	DVD	drive,	close	the	disc	tray.
	 •	 When	removing	the	disc	from	the	tray,	press	the	spindle	 to detach the disc. If trying to detach the disc forcibly, it 
can damage both the disc and the DVD drive.
 
     

20
Behind the front cover
Refer to page 21 for descriptions of how to detach the front cover.
    
 q	 Use	button	[USE]
    Use this button when adding/replacing the HDD units, or 
when changing the operational mode.
    Install/remove HDD units (+ page 52)
    Determine the operational mode of the hard disk drives 
(+ page 54)
  w  Dummy board
    When installing an optional RAID board (WJ-HDB601), 
remove the dummy board and install it.
  e  Operation button
    Use this button to operate the menu...