Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide

51
Mode	switch
Communication between the recorder and a system device using PS·Data can be performed by RS 485 inte\
rface. Devices on 
both ends of the RS485 connection are necessary to be terminated. 
The mode switch setting differs depending on whether to use the recorder as a receiver or a system controller.
When connecting RS485 cameras to the recorder, devices on both ends of the connection are necessary to be terminated.
	 •	 When	the	recorder	is	on	the	end	of	the	connection	with	a	sys-tem...

52
Install the HDD units
Install the HDD units by referring the disk slot number.
Detach the front cover in advance. (+ Page 21)
    
Install/remove	HDD	units
Step 1
Remove the HDD unit brace.
Step 2
Install the HDD units by referring the disk slot number.
  (1)  Lift the lever on the HDD unit while holding down the 
removal knob, and then insert the HDD unit all the way 
into the HDD slot.
  (2)  Pinch the rim on the HDD slot with the hook on the HDD 
unit securely.
      (3)  Press the lever down and...

53
Note:
	 •	 Hard	disk	drives	are	locally	procured.	Contact	your	deal- er for purchasing, installing, and replacing the hard disk 
drives.
	 •	 Refer	to	the	operating	instructions	of	the	extension	unit	 for how to install the HDD units on the extension unit.
 
Remove the HDD unit
Step 1
Remove the HDD unit brace. (+ Page 52)
Before removing an HDD unit, turn off the power of the 
recorder (+ page 55) or the power of the HDD unit to be 
removed (+ page 133). 
Step 2
  (1)  Pull the lever while holding...

54
Step 1
Turn off the power of the recorder. (+ Page 55)
Step 2
Detach the front cover. (+ Page 21)
Step 3
Determine the operational mode using the [RAID] switch. S: Single mode (default)
R5: RAID 5 mode
R6: RAID 6 mode
Step 4
When an extension unit is connected, boot the extension 
unit first before booting the recorder.
    Step 5
Press the power switch while holding down the [USE] but-
ton.
  →  When the recorder is booted, the setting will be applied, 
and the hard disk drives will be automatically...

55
Turn on the power
Turn on the power of the recorder.
    
Startup
Step 1
Connect the power plug to an electric outlet.
Step 2
Press the power switch at the rear of the recorder to turn on 
the power.
  →  The operate indicator will light and the system check 
(checking the recorder and the hard disk drives) will 
start.
    The startup screen will be displayed on Monitor 2 during 
the system check process.
    When the system check is complete, live images from 
the camera will be displayed (+...

56
Configure the minimum settings required to use the recorder such as the time and date setting, the language setting, the setting\
s 
relating to recording and the schedule settings on the "Quick" page of the setup menu.
Refer to page 59 for further information about the basic operations of t\
he setup menu.
    
Configure the minimum settings required to use the recorder
Step 1
Hold down the [SETUP/ESC] button for 2 seconds or more.
  →  The setup menu ("Setup" tab under the...

57
Configuration of each setting item in the setup menu should be completed\
 in advance to use this recorder. 
The operations in the setup menu are performed with either of the following:
	 •	 Displaying	the	setup	menu	on	Monitor	2	by	using	buttons	on	the	front	cover	or	a	mouse	connected	to	the	recorder
	 •	 Displaying	the	setup	menu	on	the	web	browser	of	a	PC	monitor	(when	controlling	the	recorder	via	a	network
When operating the recorder using the web browser, the setup menu will be displayed by...

58
 q	 [Quick]	button
    Select this button to display the "Quick" page (+ page 
63). The minimum settings required to operate the 
recorder such as the time & date, language, recording 
schedule, etc. can be configured on the "Quick" page. 
  w	 [Basic]	button
    Select this button to display the "Basic" page (+ page 
65). The basic settings relating to the system such as 
time & date, recording actions and audio and the set-
tings relating to the emergency recording can be...

59
 !1	 [Maintenance]	button
    Select this button to display the "Maintenance" page (+ 
page 119). 
    Check and setup of the hard disk drive information of 
the recorder, management of the setup data and check 
of log information can be carried out on the 
"Maintenance" page. Formatting SD memory cards and 
displaying the disk configuration page can also be car-
ried out on the "Maintenance" page. 
      
!2	 [Exit]	button
    Exits the setup menu when finishing the operation...

60
Step 3Select the desired tab. 
Press the [SET] button after moving the cur-
sor to the desired tab using the arrows button 
(C D A B). 
→	  The setup menu page of the selected tab 
will be displayed. 
    Step 3
Select the desired tab. 
Put the mouse cursor on the desired tab, and click the 
mouse button. 
  →  The setup menu page of the selected tab will be dis-
played. 
    
Operation using buttons on the front cover
Step 2
Select the desired setup menu. 
Press the [SET] button after moving the...