Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide

31
When	connecting	a	monitor	using	a	HDMI	cable
Note:
	 •	 Make	sure	to	use	a	HDMI	cable	compliant	with	the	HDMI	(high-speed)	standard.
	 •	 Use	a	HDMI	cable	whose	length	is	10	m	{32.81	ft}	or	less	to	prevent	image	quality	deterioration	and	unstable	performance.
	 •	 When	using	a	HDMI	cable,	audio	can	be	heard	from	the	connected	monitor.	Audio	can	be	heard	only	from	Monitor	2.
 
    
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT...

32
Connection of a PC
Connect a PC and the recorder. Required devices and cables vary depending on how to connect them. Before starting the con-
nection, prepare the required devices and cables.
Connect a PC and the recorder directly
Use a LAN cable to connect a PC and the recorder directly.Important:
	 •	 When	connecting	a	PC	and	the	recorder	directly	(without	using	a	hub/router),	make	sure	to	use	a	cross	LAN	cable.
	 •	 This	connection	is	only	for	the	setting	configuration.	Operation	of	the	recorder...

33
Connection	of	an	extension	unit
Up to 3 extension units (optional) can be connected to a single recorder. Use the dedicated cable (provided with the extension 
unit) to connect between the extension unit and the recorder.
When connecting multiple extension units (WJ-HDE400) or when newly add\
ing extension units, connect as follows. Refer also to 
the operating instructions of the extension unit.Important:
	 •	 Make	sure	to	use	the	dedicated	cable	provided	with	the	extension	unit	to	connect.
	 •	 Fix...

34
Connection	of	a	VCR
When copying images recorded on the recorder to a VCR, connect cables from a VCR to the video output connector and the 
audio connector inside the SDHC/SD memory card slot cover at the front of the recorder.Note:
	 •	 The	same	images	displayed	on	Monitor	2	will	be	output	from	the	video	output	connector	on	the	front	of	the	recorder	(except	 when another recorder is connected in cascading connection).The audio output connectors o\
n the front and rear are 
designed to output the same...

35
Connection of a PS·Data compatible device
The following are examples when connecting PS·Data compatible devices to the recorder. When connecting a PS·Data compati-
ble system controller, it is possible to operate devices connected to the recorder using the system controller.
Use an RS485 cable to connect a PS·Data compatible system controller.Important:
	 •	 Select	"On"	for	the	termination	setting	of	the	devices	on	both	ends	of	the	connection.	Refer	to	the	operating	instructions	of	 each...

36
When connecting the recorder between a system controller and a system device
    
When connecting a system device to the recorder
    
EXT STORAGEMODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
POWER ON
OFF ALARM
Data Multiplex Unit WJ-MP204
ALARM...

37
Cascading connection of multiple recorders
Up to 5 recorders can be connected in cascading connection.
When connecting recorders in cascading connection, images displayed on Monitor 2 connected to\
 the second and subsequent 
recorders can be switched and displayed on Monitor 2 connected to the first r\
ecorder.
Use the cascade input connector, cascade output connector (monitor output connector 2 is provided as the dual purpose con-
nector) and DATA port.
Cables are to be connected differently between...

38
Cascading	connection	using	HDMI	cables
Important:
	 •	 Up	to	5	recorders	and	a	single	system	controller	can	be	connected.
	 •	 Connect	the	recorder	whose	unit	address	(system)	is	even	number	to	the	cascade	input	1	connector	of	the	first	recorder.	 Connect the recorder whose unit address (system) is odd number to the cascade input 2 connector of the sec\
ond recorder.
    Connect the fourth and fifth recorders to the cascade input 1 connectors of the second and third recorders respectively.
 
Note:
	 •...

39
Connection of PS·Data compatible devices
When connecting a PS·Data compatible system controller to the first recorder
    
The Unit address setting on the 
[PS·Data setup] tab under 
Communication of the setup 
menu
EXT STORAGEMODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON...

40
When connecting a PS·Data compatible system controller to the third recorder
    
EXT STORAGEMODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN...