Home
>
Panasonic
>
Recording Equipment
>
Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide
Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide
Have a look at the manual Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 29
29
Connection of cameras
Up to 16 cameras (system cameras or combination cameras) can be connec\
ted to the video input connector 1-16.Important:
• When using with a Panasonic's matrix switcher or a coaxial communication unit, make sure that the loop-through output connection (of each video input) to the recorder are correctly made. When a monitor output or a spot output is connected to
the video input connector of the recorder, noise may be produced upon switching camera channels or images of...](http://img.usermanuals.tech/thumb/58/72217/w64_wj-hd616_716_installation_guide_d-28.png "Page 29
29
Connection of cameras
Up to 16 cameras (system cameras or combination cameras) can be connec\
ted to the video input connector 1-16.Important:
• When using with a Panasonic's matrix switcher or a coaxial communication unit, make sure that the loop-through output connection (of each video input) to the recorder are correctly made. When a monitor output or a spot output is connected to
the video input connector of the recorder, noise may be produced upon switching camera channels or images of...")
![Page 30
30
Connection of monitors
Connect monitors to the monitor output connector.
Connect a monitor to be used to display live images only to the monitor \
output connector 1.
Connect a monitor to be used to display not only live images but also recorded images and setup menu to the monitor output
connector 2.
The monitor can be connected using a BNC cable or a HDMI cable. (There is no difference in contents to be output to each
monitor.)
When connecting a monitor using a BNC cable
EXT STORAGEMODE
D...](http://img.usermanuals.tech/thumb/58/72217/w64_wj-hd616_716_installation_guide_d-29.png "Page 30
30
Connection of monitors
Connect monitors to the monitor output connector.
Connect a monitor to be used to display live images only to the monitor \
output connector 1.
Connect a monitor to be used to display not only live images but also recorded images and setup menu to the monitor output
connector 2.
The monitor can be connected using a BNC cable or a HDMI cable. (There is no difference in contents to be output to each
monitor.)
When connecting a monitor using a BNC cable
EXT STORAGEMODE
D...")
![Page 33
33
Connection of an extension unit
Up to 3 extension units (optional) can be connected to a single recorder. Use the dedicated cable (provided with the extension
unit) to connect between the extension unit and the recorder.
When connecting multiple extension units (WJ-HDE400) or when newly add\
ing extension units, connect as follows. Refer also to
the operating instructions of the extension unit.Important:
• Make sure to use the dedicated cable provided with the extension unit to connect.
• Fix...](http://img.usermanuals.tech/thumb/58/72217/w64_wj-hd616_716_installation_guide_d-32.png "Page 33
33
Connection of an extension unit
Up to 3 extension units (optional) can be connected to a single recorder. Use the dedicated cable (provided with the extension
unit) to connect between the extension unit and the recorder.
When connecting multiple extension units (WJ-HDE400) or when newly add\
ing extension units, connect as follows. Refer also to
the operating instructions of the extension unit.Important:
• Make sure to use the dedicated cable provided with the extension unit to connect.
• Fix...")
![Page 34
34
Connection of a VCR
When copying images recorded on the recorder to a VCR, connect cables from a VCR to the video output connector and the
audio connector inside the SDHC/SD memory card slot cover at the front of the recorder.Note:
• The same images displayed on Monitor 2 will be output from the video output connector on the front of the recorder (except when another recorder is connected in cascading connection).The audio output connectors o\
n the front and rear are
designed to output the same...](http://img.usermanuals.tech/thumb/58/72217/w64_wj-hd616_716_installation_guide_d-33.png "Page 34
34
Connection of a VCR
When copying images recorded on the recorder to a VCR, connect cables from a VCR to the video output connector and the
audio connector inside the SDHC/SD memory card slot cover at the front of the recorder.Note:
• The same images displayed on Monitor 2 will be output from the video output connector on the front of the recorder (except when another recorder is connected in cascading connection).The audio output connectors o\
n the front and rear are
designed to output the same...")
31
When connecting a monitor using a HDMI cable
Note:
• Make sure to use a HDMI cable compliant with the HDMI (high-speed) standard.
• Use a HDMI cable whose length is 10 m {32.81 ft} or less to prevent image quality deterioration and unstable performance.
• When using a HDMI cable, audio can be heard from the connected monitor. Audio can be heard only from Monitor 2.
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
1
34567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
HDMI cable
(locally procured)
Monitor 2
Recorder
Monitor 1
32
Connection of a PC
Connect a PC and the recorder. Required devices and cables vary depending on how to connect them. Before starting the con-
nection, prepare the required devices and cables.
Connect a PC and the recorder directly
Use a LAN cable to connect a PC and the recorder directly.Important:
• When connecting a PC and the recorder directly (without using a hub/router), make sure to use a cross LAN cable.
• This connection is only for the setting configuration. Operation of the recorder cannot be performed by this connection.
Add the recorder to the existing network
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE12
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21
3
4
5
6
7 7
1
2
1
2
8
9
10
11
12
13
14
15
16 POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUT CASCADE1
2
IP address 192.168.0.x (except 0, 250 and 255)
Subnet mask 255.255.255.0
Recorder
IP address 192.168.0.250
Subnet mask 255.255.255.0
LAN cable
(locally procured: 10BASE-T/100BASE-TX,
category5, cross)
PC PC
Recorder
IP address 192.168.0.250
Subnet mask 255.255.255.0
Gateway address: 192.168.0.1 LAN cable
(locally procured: 10BASE-T/
100BASE-TX, category5, straight)
IP address 192.168.0.x
(except 0, 1, 250 and 255)
Subnet mask 255.255.255.0
Gateway address: 192.168.0.1
LAN*
Hub/Router
IP address: 192.168.0.1
Subnet mask: 255.255.255.0 FTP server
(for image transmission)
* Stands for Local Area Network
EXT STORAGE
MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21
3
4
5
6
7 7
1
2
1
2
8
9
10
11
12
13
14
15
16 POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUT CASCADE1
2
EXT STORAGE
MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE12
IP address 192.168.0.x (except 0, 250 and 255)
Subnet mask 255.255.255.0
Recorder
IP address 192.168.0.250
Subnet mask 255.255.255.0 LAN cable
(locally procured: 10BASE-T/100BASE-TX,
category5, cross)
PC PC
Recorder
IP address 192.168.0.250
Subnet mask 255.255.255.0
Gateway address: 192.168.0.1 LAN cable
(locally procured: 10BASE-T/
100BASE-TX, category5, straight)
IP address 192.168.0.x
(except 0, 1, 250 and 255)
Subnet mask 255.255.255.0
Gateway address: 192.168.0.1
LAN*
Hub/Router
IP address: 192.168.0.1
Subnet mask: 255.255.255.0 FTP server
(for image transmission)
* Stands for Local Area Network
33
Connection of an extension unit
Up to 3 extension units (optional) can be connected to a single recorder. Use the dedicated cable (provided with the extension
unit) to connect between the extension unit and the recorder.
When connecting multiple extension units (WJ-HDE400) or when newly add\
ing extension units, connect as follows. Refer also to
the operating instructions of the extension unit.Important:
• Make sure to use the dedicated cable provided with the extension unit to connect.
• Fix the connection cable firmly using the cable clamp provided with the extension unit. When the cable is not connected firm- ly or when it is disconnected, the system may become unstable or recording may fail.
• Do not loop and bundle the cable in a circle.
• When installing the recorder or the extension unit in the rack, make a space of 1U (44 mm) above and below each of them for ventilation.
EXT IN
POWERON
OFF
EXT IN
POWERON
OFF
EXT IN
POWERON
OFF
EXT STORAGE MODE
D ATA
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE INMONITOR
OUTOUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE121
23
Extension unit (Unit number: 3) Extension unit (Unit number: 2) Extension unit (Unit number: 1)
Connection cable (provided with the extension unit)
Recorder
Fix the connection cable
Attach the cable clamp to each connection cable.
Refer to the operating instructions of the extension
unit for how to attach the cable clamp.
Fix the connection cable
34
Connection of a VCR
When copying images recorded on the recorder to a VCR, connect cables from a VCR to the video output connector and the
audio connector inside the SDHC/SD memory card slot cover at the front of the recorder.Note:
• The same images displayed on Monitor 2 will be output from the video output connector on the front of the recorder (except when another recorder is connected in cascading connection).The audio output connectors o\
n the front and rear are
designed to output the same audio.
• When connecting multiple recorders in cascading connection, it is impossible to output video signals of another WJ-HD616K/WJ-HD716K from the video output connector. Connect VCRs to each recorder (WJ-HD616K/WJ-HD716K).
4321
8765
12110/109
16151413
STOP
MOUSEDigital Disk Recorder WJ-HD616
REV FWD
GOTO LAST
SUB
MENU SETHOLD
GOTO DATESEARCH COPY
SETUP /ESC
PAUSEPLAYRECREC STOPMONITORSEQOSD
MULTI SCREENERROR
TIMER STS
A/F
HDD 1
HDD 2
HDD 3
HDD 4
OPERATE ALARM
ALARM
RESET
ALARM
SUSPEND
VIDEO
OUT
AUDIO
OUT
VCR
AUDIO IN VIDEO
IN
Open the SDHC/SD memory card slot. Recorder
Audio cable with plugs
(locally procured)
Video cable with plugs
(locally procured)
35
Connection of a PS·Data compatible device
The following are examples when connecting PS·Data compatible devices to the recorder. When connecting a PS·Data compati-
ble system controller, it is possible to operate devices connected to the recorder using the system controller.
Use an RS485 cable to connect a PS·Data compatible system controller.Important:
• Select "On" for the termination setting of the devices on both ends of the connection. Refer to the operating instructions of each device on both ends of the connection. The termination setting of t\
he recorder can be set using the mode switch. (+
Page 51)
• When connecting a PS·Data compatible system controller, configure the settings on the [PS·Data setup] tab under the "Communication" page of the setup menu according to the connection. (+ Page 93)
• "PS·Data" is Panasonic's proprietary protocol. Contact your dealer for devices that can be connected.
• Do not assign the same unit address to two or more different PS·Data compatible devices.
When connecting a system controller to the recorder
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
1
34567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
7 8
ON6
1 2 3 4 5
Setup menu Communication - [PS·Data setup]
■ Unit address (system): 1
■ Unit address (controller): 2 Controller
Termination: On
Unit address: 1
RS485 cable (provided with the controller)
Recorder Mode switch
(No.7: ON)
(No.8: OFF)
36
When connecting the recorder between a system controller and a system device
When connecting a system device to the recorder
EXT STORAGEMODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
POWER ON
OFF ALARM
Data Multiplex Unit WJ-MP204
ALARM
SUSPEND1 2 34
ESC
SE T
RESE
TSUSPEND SE T UPALARM
UNIT
7 8
ON6
1 2 3 4 5
Mode switch
(No.7: OFF)
(No.8: OFF) RS485 cable
(provided with the controller)
Recorder Controller
Termination: On
Unit address: 1
Setup menu Communication - [PS·Data setup]
■ Unit address (system): 1
■ Unit address (controller): 2
Coaxial communication unit
Termination: On
Unit address: 2
RS485 cable
(WV-CA48/50)
EXT STORAGE
MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
POWER ON
OFF ALARM
Data Multiplex Unit WJ-MP204
ALARM
SUSPEND1 2 34
ESC
SE T
RESE
TSUSPEND SE T UPALARM
UNIT
POWER
ON
OFF ALARM
Data Multiplex Unit WJ-MP204
ALARM
SUSPEND1 2 34
ESC
SE T
RESE
TSUSPEND SE T UPALARM
UNIT
7 8
ON6
1 2 3 4 5
Mode switch
(No.7: OFF)
(No.8: ON) RS485 cable
(WV-CA48/50)
RS485 cable
(WV-CA48/10K)
Setup menu Communication - [PS·Data setup]
■ Unit address (system): 1
■ Unit address (controller): 1 Coaxial communication unit
Termination: OFF
Unit address: 2Coaxial communication unit
Termination: ON
Unit address: 3
Recorder
37
Cascading connection of multiple recorders
Up to 5 recorders can be connected in cascading connection.
When connecting recorders in cascading connection, images displayed on Monitor 2 connected to\
the second and subsequent
recorders can be switched and displayed on Monitor 2 connected to the first r\
ecorder.
Use the cascade input connector, cascade output connector (monitor output connector 2 is provided as the dual purpose con-
nector) and DATA port.
Cables are to be connected differently between when using HDMI cables and when using BNC cables.Important:
• When multiple recorders are connecting in cascading connection, select "On" for the "Cascade" setting on the [Cascade] tab under the "Display" page of the setup menu. (+ Page 91)
• When connecting in cascading connection, all cables used to connect to the monitor connector shall be HDMI cables only or BNC cables only. Do not use them together.
• Do not assign the same unit address to two or more different PS·Data compatible devices.
• Set the unit address (system) of the recorders to "1" to "5".
• In cascading connection, the time of recorders is automatically adjusted to that of the recorder whose unit address (system) is set to "1".
• When connecting in cascading connection, all recorders shall be WJ-HD616K.
Cascading connection using BNC cables
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE12
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE12
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE12
7 8
ON6
1 2 3 4 5
7 8
ON6
1 2 3 4 5
7 8
ON6
1 2 3 4 5
Monitor 2 Monitor 1
Monitor 1
Monitor 1 Mode switch
Mode switch
Mode switch
(No.7: OFF)
(No.8: ON)
(No.7: OFF)
(No.8: OFF)
(No.7: OFF)
(No.8: ON)
* When also connecting audio cables in cascading connection
Powered
speaker
BNC cable
(locally procured)
BNC cable
(locally procured)
BNC cable
(locally procured) Audio cable
(locally procured)
RS485
cable
(WV-CA
48/50)
RS485
cable
(WV-CA
48/50) First recorder
System: 1
Controller: 1
Second recorder
System: 2
Controller: 2
Audio cable
(locally procured) Third recorder
System: 3
Controller: 3The Unit address setting on the
[PS·Data setup] tab under
Communication of the setup
menu
38
Cascading connection using HDMI cables
Important:
• Up to 5 recorders and a single system controller can be connected.
• Connect the recorder whose unit address (system) is even number to the cascade input 1 connector of the first recorder. Connect the recorder whose unit address (system) is odd number to the cascade input 2 connector of the sec\
ond recorder.
Connect the fourth and fifth recorders to the cascade input 1 connectors of the second and third recorders respectively.
Note:
• Connection using the DATA port (with RS485 cables) can be made in the same manner as connection using the BNC cables (+ page 37).
• When connecting using the HDMI cables, audio will be output together (However, audio will not be output from the audio output connector (RCA pin jack).)
• In cascading connection, it may take time to change the monitor display.
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE12
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE12
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE12
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE12
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 21345677
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE12
The Unit address setting on the
[PS·Data setup] tab under
Communication of the setup
menu
Monitor 2
First recorder
System: 1
Controller: 1
Third recorder
System: 3
Controller: 3 Second recorder
System: 2
Controller: 2
Fifth recorder
System: 5
Controller: 5 Fourth recorder
System: 4
Controller: 4
HDMI cable
(sold separately)
39
Connection of PS·Data compatible devices
When connecting a PS·Data compatible system controller to the first recorder
The Unit address setting on the
[PS·Data setup] tab under
Communication of the setup
menu
EXT STORAGEMODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
7 8
ON6
1 2 3 4 5
7 8
ON6
1 2 3 4 5
7 8
ON6
1 2 3 4 5
Mode switch
Mode switch
Mode switch (No.7: OFF)
(No.8: OFF)
(No.7: OFF)
(No.8: OFF)
(No.7: ON)
(No.8: OFF) RS485 cable
(WV-CA48/50)
RS485 cable
(WV-CA48/50) First recorder
System: 1
Controller: 2
Second recorder
System: 2
Controller: 3Third recorder
System: 3
Controller: 4
RS485 cable
(provided with the controller)
Controller
Termination: On
Unit address: 1
40
When connecting a PS·Data compatible system controller to the third recorder
EXT STORAGEMODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
EXT STORAGE MODE
D ATARS485(CAMERA)10/100BASE-T
ALARM
VIDEO
OUT
-CASCADE-IN
ALARM/CONTROL CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD) AUDIO IN AUDIO
OUT
3
2 1
1 2 3 4 5 6 7 81
2
3
4 4 2 3 1
12
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT 2
134567
7
12
1
2
8910111213141516
POWER
AC IN SIGNAL
GND ON
OFF
OUT
IN
OUTCASCADE
1
2
POWER ON
OFF ALARM
Data Multiplex Unit WJ-MP204
ALARM
SUSPEND1 2 34
ESC
SE T
RESE
TSUSPEND SE T UPALARM
UNIT
7 8
ON6
1 2 3 4 5
7 8
ON6
1 2 3 4 5
7 8
ON6
1 2 3 4 5
Mode switch
Mode switch
Mode switch (No.7: OFF)
(No.8: ON)
(No.7: OFF)
(No.8: OFF)
(No.7: OFF)
(No.8: OFF)
RS485 cable
(WV-CA48/50)
RS485 cable
(WV-CA48/50)
RS485 cable
(WV-CA48/50) First recorder
System: 1
Controller: 1
Second recorder
System: 2
Controller: 2
Third recorder
System: 3
Controller: 3Coaxial communication unit
Termination: On
Unit address: 6
The Unit address setting on the
[PS·Data setup] tab under
Communication of the setup
menu
* Set 6 or greater numbers for the unit addresses of system devices such as a coaxial communication unit.