OKI MC560n User Manual

Maintenance > 81
REPLACING CONSUMABLE ITEMS
TONER CARTRIDGE REPLACEMENT
The toner used in this machine is a very fine dry powder. It is contained in four cartridges: 
one each for cyan, magenta, yellow and black.
Have a sheet of paper handy so that you have somewhere to place the used cartridge while 
you install the new one.
Dispose of the old cartridge responsibly, inside the pack that the new one came in. Follow 
any regulations, recommendations, etc., which may be in force concerning waste...

Maintenance > 82
3.Note the positions of the four cartridges.
(a) Pull the coloured toner release lever (1) on the cartridge to be replaced fully 
towards the front of the MFP.
4.Lift the right-hand end of the cartridge and then draw the cartridge to the right to 
release the left-hand end as shown, and withdraw the toner cartridge out of the 
MFP.
5.Put the cartridge down gently onto a piece of paper to prevent toner from marking 
your furniture.
6.Remove the new cartridge from its box but leave its...

Maintenance > 83
7.Gently shake the new cartridge from end to end several times to loosen and 
distribute the toner evenly inside the cartridge.
8.Remove the wrapping material and peel off the adhesive tape from the underside of 
the cartridge.
9.Holding the cartridge by its top centre with the coloured lever to the right, lower it 
into the printer over the image drum unit from which the old cartridge was removed.
10.Insert the left end of the cartridge into the top of the image drum unit first, pushing...

Maintenance > 84
13.Gently lower the scanner.
IMAGE DRUM REPLACEMENT
The MFP contains four image drums: cyan, magenta, yellow and black.
1.Gently raise the scanner.
2.Press the cover release (a) and open the MFP’s top cover (b) fully.
CAUTION!
 Static sensitive devices, handle with care.
WARNING!
If the MFP has been powered on, the fuser will be hot. This area is 
clearly labelled. Do not touch.
b
a
Downloaded From ManualsPrinter.com Manuals 

Maintenance > 85
3.Note the positions of the four cartridges.
4.Holding it by its top centre, lift the image drum, complete with its toner cartridge, up 
and out of the MFP.
5.Put the cartridge down gently onto a piece of paper to prevent toner from marking 
your furniture and to avoid damaging the green drum surface.
6.With the coloured toner release lever (1) to the right, pull the lever towards you. 
This will release the bond between the toner cartridge and the image drum 
cartridge.
7.Lift the...

Maintenance > 86
image drum cartridge. Place the cartridge on a piece of paper to avoid marking your 
furniture.
8.Take the new image drum cartridge out of its packaging and place it on the piece of 
paper where the old cartridge was placed. Keep it the same way round as the old 
unit. Pack the old cartridge inside the packaging material for disposal.
9.Place the toner cartridge onto the new image drum cartridge as shown. Push the left 
end in first, and then lower the right end in. (It is not necessary...

Maintenance > 87
13.Gently lower the scanner.
TRANSFER BELT REPLACEMENT
The belt unit is located under the four image drums. This unit requires replacement 
approximately every 60,000 pages.
Switch off the MFP and allow the fuser to cool for about 10 minutes before opening the 
cover.
1.Gently raise the scanner.
2.Press the cover release (a) and open the MFP’s top cover (b) fully.
NOTE
If you need to return or transport this product for any reason, please make 
sure you remove the image drum unit...

Maintenance > 88
3.Note the positions of the four cartridges. It is essential that they go back in the same 
order 
4.Lift each of the image drum units out of the MFP and place them in a safe place away 
from direct sources of heat and light.
5.Locate the two fasteners (5) at each side of the belt and the lifting bar (6) at the 
front end.
1. Cyan cartridge 2. Magenta cartridge
3. Yellow cartridge 4. Black cartridge
CAUTION!
The green image drum surface at the base of each cartridge is very 
delicate and...

Maintenance > 89
6.Turn the two fasteners 90° to the left. This will release the belt from the MFP 
chassis.
7.Pull the lifting bar (6) upwards so that belt tilts up towards the front, and withdraw 
the belt unit from the MFP.
8.Lower the new belt unit into place, with the lifting bar at the front and the drive gear 
towards the rear of the MFP. Locate the drive gear into the gear inside the printer by 
the rear left corner of the unit, and lower the belt unit flat inside the MFP.
9.Turn the two...

Maintenance > 90
2.Press the cover release (a) and open the MFP’s top cover (b) fully.
3.Identify the fuser handle (1) on the top of the fuser unit.
4.Pull the two fuser retaining levers (2) towards the front of the printer so that they 
are fully upright.
5.Holding the fuser by its handle (1), lift the fuser straight up and out of the MFP. If 
the fuser is still warm, place it on a flat surface which will not be damaged by heat.
6.Remove the new fuser from its packaging and remove the transit material....