OKI C130n User Manual
Have a look at the manual OKI C130n User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 103 Oki manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
81 - C130n User’s Guide Important! Do not touch the contact indicated in the illustration. 10Press in the toner cartridge until it locks into place. 11Close the front cover. NoteThe printer must complete a calibration cycle (less than 2 minutes) after the toner cartridge has been replaced. If you open the top or front cover before the message IDLE appears, the printer stops and repeats the calibration cycle. Downloaded From ManualsPrinter.com Manuals
82 - C130n User’s Guide Replacing All Toner Cartridges at the Same Time CAUTION Be careful not to spill toner while replacing a toner cartridge. If toner spills, immediately wipe it off with a soft, dry cloth. By using the REMOVE ALL mode, all toner cartridges can be replaced at the same time. 1Perform the operation described below to switch the printer to the REMOVE ALL mode. Press KeyUntil Display Reads MANU MAIN MANU MAIN MENU PRINT MENU × 2MAIN MENU QUALITY MENU QUALITY MENU REPLACE TONER REPLACE TONER BLACK REPLACE TONER REMOVE ALL REMOVE ALL *NO REMOVE ALL YES *YES IS SELECTED Then the display changes to OPEN DOOR AND REMOVE M TONER ENTER ENTER ENTER ENTER ENTER Downloaded From ManualsPrinter.com Manuals
83 - C130n User’s Guide NoteIt is not possible to exit REMOVE ALL mode before the operation is finished (even if the Cancel key is pressed). If the printer has incorrectly been switched to REMOVE ALL mode, open, then close the front cover four times to exit REMOVE ALL mode. 2Perform the operations described in steps 2 through 10 of “Replacing a Toner Cartridge” starting on page 6-77 to replace the magenta toner cartridge. 3Follow the same procedure to replace the cartridges for the cyan, black, then yellow toners. NoteThe printer must complete a calibration cycle (less than 2 minutes) after a toner cartridge has been replaced. If you open the top or front cover before the printer is reset, the calibration stops, then starts over again after the cover is closed. 4Press the key three times to exit the configuration menu. Downloaded From ManualsPrinter.com Manuals
84 - C130n User’s Guide Imaging Cartridges Replacing the Imaging Cartridge Important! When replacing an imaging cartridge, use only a genuine Oki imaging cartridge for your specific printer type. 1Open the top cover. NoteIf there is paper in the output tray, remove it, and then fold up the output tray before opening the top cover. 2Grab the handle and lift it up slightly to the back, and then slowly pull the imaging cartridge out vertically. Downloaded From ManualsPrinter.com Manuals
85 - C130n User’s Guide CAUTION Dispose of the used imaging cartridge according to your local regulations. Do not burn the imaging cartridge. 3Prepare the new imaging cartridge. Important! Do not touch the PC drum and the transfer belt on the imaging cartridge. 4Slowly insert the new imaging cartridge vertically, and then push it slightly down toward you to finish installing the imaging cartridge. Downloaded From ManualsPrinter.com Manuals
86 - C130n User’s Guide 5Carefully close the top cover. NoteThe printer must complete a calibration cycle (less than 2 minutes) after the imaging cartridge has been replaced. If you open the top cover before the message IDLE appears, the printer stops and repeats the calibration cycle. Downloaded From ManualsPrinter.com Manuals
87 - C130n User’s Guide The Fuser Unit Replacing the Fuser Unit Important! For optimum print quality and performance, use only a genuine Oki fuser unit for your specific printer type. 1Turn off the printer and disconnect the power cord. WARNING! There are extremely hot parts within the printer. Before replacing the fuser unit, wait about 20 minutes after turning off the printer, and then check that the fusing section has reached room temperature, otherwise, you may get burnt. Downloaded From ManualsPrinter.com Manuals
88 - C130n User’s Guide 2Open the top cover. NoteIf there is paper in the output tray, remove it, and then fold up the output tray before opening the top cover. 3Push the blue handles back as far as possible. 4Grab the blue handles and lift the fuser unit to remove it. Downloaded From ManualsPrinter.com Manuals
89 - C130n User’s Guide Important! Do not touch the matching connectors of the fuser unit and the machine. 5Prepare a new fuser unit. Downloaded From ManualsPrinter.com Manuals
90 - C130n User’s Guide aPull the fuser separator levers forward as far as pos - sible. bRemove the fuser separator material, and then return the fuser separator levers to their original positions. Downloaded From ManualsPrinter.com Manuals