OKI C130n User Manual

							91 - C130n User’s Guide
Important!
Be careful not to touch the paper exit sensor and the surface of 
the fuser roller in the fuser unit. 
  
1While lifting the fuser unit with 
the blue handles (one on each 
side), vertically insert the fuser 
unit.
 
 
 
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 
						

							92 - C130n User’s Guide
Important!
Do not touch the paper exit 
sensor on the fuser unit. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Important!
Do not touch the matching 
connectors of the fuser unit 
and the machine.
 
 
 
 
 
 
 
 
 
 
M
Downloaded From ManualsPrinter.com Manuals 
						

							93 - C130n User’s Guide
2After the fuser unit is firmly 
installed, flip the blue handles 
down toward you.
3Carefully close the top cover.
4Reconnect the power cord, and 
turn on the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							94 - C130n User’s Guide
Maintaining the 
Printer
Downloaded From ManualsPrinter.com Manuals 
						

							95 - C130n User’s Guide
Maintaining the Printer
CAUTION
Read all caution and warning labels carefully, making sure to 
follow any instructions contained in them. These labels are 
located on the inside of the printer’s covers and the interior of 
the printer body.
Handle the printer with care to preserve its life. If dust and paper scraps 
remain on the inside or outside of the printer, printer performance and print 
quality will suffer, so the printer should be cleaned periodically. Keep the 
following guidelines in mind.
WARNING!
Turn off the printer, unplug the power cord, and disconnect all 
interface cables before cleaning. Do not spill water or detergent 
into the printer; otherwise the printer will be damaged and an 
electric shock may occur.
CAUTION
The fuser unit is hot. When the top cover is opened, the 
fuser unit temperature drops gradually (one hour wait 
time).
Be careful when cleaning the inside of the printer or removing media 
misfeeds, as the fuser unit and other internal parts may be very hot.
Do not place anything on top of the printer.
Use a soft cloth to clean the printer.
Never spray cleaning solutions directly on the printer’s surface; the spray 
could penetrate through the air vents of the printer and damage the 
internal circuits.
Avoid using abrasive or corrosive solutions or solutions that contain 
solvents (such as alcohol and benzene) to clean the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							96 - C130n User’s Guide
Always test any cleaning solution (such as mild detergent) on a small 
inconspicuous area of your printer to check the solution’s performance.
Never use sharp or rough implements, such as wire or plastic cleaning 
pads.
Always close the printer’s covers gently. Never subject the printer to 
vibration.
Do not cover the printer immediately after using it. Turn it off and wait until 
it cools down.
Do not leave the printer’s covers open for any length of time, especially in 
well-lit places; light may damage the imaging cartridge.
Do not open the printer during printing.
Do not tap media stacks on the printer.
Do not lubricate or disassemble the printer.
Do not tilt the printer.
Do not touch the electrical contacts, gears, or laser devices. Doing so may 
damage the printer and cause the print quality to deteriorate.
Keep media in the output tray at a minimum level. If the media is stocked 
too high, your printer may experience media misfeeds and excessive 
media curl.
Keep the printer level to avoid toner spillage.
Downloaded From ManualsPrinter.com Manuals 
						

							97 - C130n User’s Guide
When lifting the printer, grasp the areas shown in the figure. 
Before moving the printer, remove the dust cover, and fold up Tray 1.
If the optional lower feeder unit, attachment and duplex option are 
installed, remove them and move them separately.
If you get toner on your skin, wash it off with cool water and a mild soap.
CAUTION
If you get toner in your eyes, wash it out immediately with cool 
water and consult a doctor.
Make sure any parts removed during cleaning are replaced before you 
plug in the printer.
15 kg
33 lbs
Downloaded From ManualsPrinter.com Manuals 
						

							98 - C130n User’s Guide
Cleaning the Printer
CAUTION
Be sure to turn off the printer and unplug the power cord before 
cleaning. However, be sure to turn on the printer when cleaning 
the print head window.
Cleaning the Exterior 
Control Panel 
Ventilation Grill 
YMCK
READYEADY
RO TAT EOTATETONERONER
ATTENTIONTTENTION
CANCELANCEL
Downloaded From ManualsPrinter.com Manuals 
						

							99 - C130n User’s Guide
Exterior Housing 
Cleaning the Interior
Cleaning the Media Feed Roller
1Open the top cover.
NoteIf there is paper in the 
output tray, remove it, 
and then fold up the 
output tray before 
opening the top cover.
Downloaded From ManualsPrinter.com Manuals 
						

							100 - C130n User’s Guide
2Grab the handle and lift it up 
slightly to the back, and then 
slowly pull the imaging cartridge 
out vertically.
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals