OKI C130n User Manual

							41 - C130n User’s Guide
Interface Menu
With this menu, interface settings can be specified.
The printer must be rebooted after any setting in the ETHERNET menu (for 
example, the TCP/IP address) is changed.
Therefore, the following message appears when the configuration menu is 
exited (the + key is repeatedly pressed) after a setting has been changed. 
Select YES, and then press the Enter key to reboot the printer.
Otherwise, turn off the printer, and then turn the printer on again after a few 
seconds.
Interface Menu Tree
ETHERNET
> TCP/IP
- ENABLE
- IPV4
• DHCP/BOOTP
• IPV4 ADDRESS
• DEFAU7LT ROUTER
• SUBNET MASK
• ENABLE AUTO IP
- PV6
> IP SERVICES
- ENABLE HTTP
- DISABLE FILTERS
- DISABLE IPSEC
> IPX/SPX
- FRAME TYPE
> ETHERNET SPEED
> DISABLE 802.1X
> PS PROROCOL
> USB
- ENABLE
- JOB TIMEOUT
Downloaded From ManualsPrinter.com Manuals 
						

							42 - C130n User’s Guide
NoteIf  
MAIN MENU 
 /SYSTEM DEFAULT 
  /SECURITY 
   /CONFIG 
    /ENABLE 
is set to ON, the administrator password must be entered to display 
this menu.
 
 
For details on the default administrator password, refer to 
“SYSTEM DEFAULT” on page 46.
Downloaded From ManualsPrinter.com Manuals 
						

							43 - C130n User’s Guide
Interface Menu
NoteAll factory default values are shown in bold.
ETHERNETTCP/IPENABLESettingsYES/NO
If YES is selected, TCP/IP is enabled.
If NO is selected, TCP/IP is disabled.
IPV4DHCP/
BOOTPSettingsYES/NO
Select whether or not the IP address 
is automatically acquired.
If YES is selected, the IP address is 
automatically acquired.
If NO is selected, the IP address is 
not automatically acquired.
IPV4 
ADDRESSSettings192.168.001.002
Set the IPv4 address for this printer 
on the network.
Use the , , , and  keys to 
specify the value.
If the IP address is manually 
specified, DHCP/BOOTP is 
automatically set to NO.
DEFAULT 
ROUTERSettings000.000.000.000
Specify the IPv4 address of the router 
if one is on the network. Use the 
, 
, , and  keys to specify the value.
SUBNET 
MASKSettings000.000.000.000
Specify the subnet mask for the 
network.
Use the , , , and  keys to specify the value.
Downloaded From ManualsPrinter.com Manuals 
						

							44 - C130n User’s Guide
ETHERNET 
(cont.)ENABLE 
AUTO IPSettingsYES/NO
Select whether or not the IPv4 
address is automatically acquired 
when DHCP/BOOTP and PING, ARP 
are not functioning or when there is 
no response.
If YES is selected, the IP address is 
automatically acquired.
If NO is selected, the IP address is 
not automatically acquired.
IPV6ENABLESettingsYES/NO
If YES is selected, IPv6 is enabled.
If NO is selected, IPv6 is disabled.
IDENTIFIERDisplays the Link-Local address.
ENABLE 
AUTOSettingsYES/NO
If YES is selected, auto configuration 
of IPv6 is enabled.
If NO is selected, auto configuration 
of IPv6 is disabled.
GLOBAL 
PREFIXDisplays the global address.
IP 
SERVICESENABLE 
HTTPSettingsYES/NO
If YES is selected, HTTP is enabled.
If NO is selected, HTTP is disabled.
DISABLE 
FILTERSSettingsYES/NO
If YES is selected, filter is enabled.
If NO is selected, filter is disabled.
DISABLE 
IPSECSettingsYES/NO
If YES is selected, IPsec is enabled.
If NO is selected, IPsec is disabled.
Interface Menu
NoteAll factory default values are shown in bold.
Downloaded From ManualsPrinter.com Manuals 
						

							45 - C130n User’s Guide
ETHERNET 
(cont.)IPX/SPXFRAME TYPESettingsAUTO, 802.2, 802.3, ETHER II, 
SNAP
Specify the protocol used with NetWare.
ETHERNE
T SPEEDSettingsAUTO, 100 FULL DUPLEX, 100 HALF DUPLEX, 10 
FULL DUPLEX, 10 HALF DUPLEX
Specify the transmission speed for the network and the transmission 
method for bi-directional transmission.
DISABLE 
802.1XSettingsYES, NO
If YES is selected, IEEE802.1x function is enabled.
If NO is selected, IEEE802.1x function is disabled.
PS 
PROTOCOL
SettingsBINARY, QUOTED BINARY
Select whether PostScript jobs are received in the binary format or 
the quoted format.
USBENABLESettingsYES, NO
If YES is selected, USB is enabled.
If NO is selected, USB is disabled.
JOB 
TIMEOUTSettings0-60-999
Specify the length of time (in seconds) until the print job being 
received is timed out when USB is being used.
Interface Menu
NoteAll factory default values are shown in bold.
Downloaded From ManualsPrinter.com Manuals 
						

							46 - C130n User’s Guide
SYSTEM DEFAULT
With this menu, settings can be specified to adjust the operation of the printer, 
such as the time until the machine enters Energy Saver mode.
System Default Menu Tree
PRINT QUALITY
COLOR MODE
EMULATIONS
> DEFAULT
> AUTO DEFAULT
> POSTSCRIPT
- ERROR PAGE
> PCL
- LINE TERMINATION
- FONT
• PITCH SIZE
• FONTNUMBER
• POINT SIZE
• SYMBOL SET
STARTUP OPTIONS
> START PAGE
DATE & TIME
ENERGY SAVER
SECURITY
> CONFIG
- ENABLE
FORMAT
> FLASH
- SET USER PASSWD
RESTORE/SAVE
> RESTORE FACTORY
> SAVE CUSTOM
> RESTORE CUSTOM
Downloaded From ManualsPrinter.com Manuals 
						

							47 - C130n User’s Guide
NoteIf  
MAIN MENU 
/SYSTEM DEFAULT 
/SECURITY 
/CONFIG 
/ENABLE  
is set to ON, the administrator password must be entered to display 
this menu. 
System Default Menu
NoteAll factory default values are shown in bold.
PRINT 
QUALITYSettingsHIGH, STANDARD
Select the image quality for prints.
COLOR 
MODESettingsCOLOR, GRAYSCALE
Specify whether printing is in full color or grayscale.
NoteThe color mode setting specified from the printer driver has 
priority over the setting specified for this menu item.
Downloaded From ManualsPrinter.com Manuals 
						

							48 - C130n User’s Guide
EMULA-
TIONS
DEFAULTSettingsAUTOMATIC, POSTSCRIPT, PCL5, PCL XL, 
HEX DUMP
Specify the printer control language.
If AUTOMATIC is selected, the printer automatically 
selects the printer control language from the data stream.
AUTO 
DEFAULTSettingsPCL5, POSTSCRIPT
Select the printer description language when it cannot be 
identified from the data.
POSTSCRIP
TERROR 
PA G ESettingsON, OFF
Select whether or not an error page is printed 
when a PostScript error occurs.
PCLLINE 
TERMINA
TIONSettingsCR=CR LF=CRLF,  CR=CR LF=LF, 
CR=CRLF LF=LF, 
CR=CRLF LF=CRLF
Select the definitions of the CR/LF codes in 
the PCL language.
FONTPITCH 
SIZESettings44-1000-9999
Specify the bitmap font size in the 
PCL language.
FONT 
NUMBERSettings0-32767
Specify the font used with the PCL 
language.
The font numbers that appear 
correspond to the PCL font list. 
For details on printing the font list, 
refer to 
“PRINT MENU” on page 32.
POINT 
SIZESettings400-1200-99975
Specify the outline font size in the 
PCL language.
SYMBOL 
SETSpecify the symbol set used with 
the PCL language.
The default setting is PC8.
System Default Menu
NoteAll factory default values are shown in bold.
Downloaded From ManualsPrinter.com Manuals 
						

							49 - C130n User’s Guide
STARTUP 
OPTIONSSTART 
PA G ESettingsYES, NO
Select whether or not a startup page is printed when the 
printer is turned on.
If YES is selected, the startup page is printed when the 
printer is turned on.
If NO is selected, the startup page is not printed.
DATE & 
TIMESettingsyyyymmdd:hhmmss
Set the date and time on the time-of-day (TOD) clock.
The settings appear in the following order: year, month, day:hour, 
minutes, seconds.
ENERGY 
SAVERSettings15 MINUTES, 30 MINUTES,1 HOUR,2 HOURS
Specify the length of time until the machine enters Energy Saver mode.
Note2 HOURS is displayed only on 120 V units.
SECURITYCONFIGENABLESettingsON/OFF
Select whether or not the menus are protected 
with a password.
If ON is selected, all menus are protected with 
a password.
SET 
USER 
PASSWDSettings: 1
Specify the user password for displaying the 
user menus. The specified password is 
applied only if MAIN MENU/SYSTEM 
DEFAULT/SECRITY/CONFIG/ENABLE is set 
to ON.
The password can contain a maximum of 16 
characters.
NoteEmpty passwords are not allowed.
System Default Menu
NoteAll factory default values are shown in bold.
Downloaded From ManualsPrinter.com Manuals 
						

							50 - C130n User’s Guide
SERVICE MENU
With this menu, the service representative can adjust the printer and perform 
maintenance operations. This menu cannot be accessed by the user.
SECURITY 
(cont.)SET 
ADMIN 
PASSWDSettings: the last four digits of the printer serial 
number
Specify the administrator password for 
displaying the administrator menus. The 
specified password is applied only if MAIN 
MENU/SYSTEM DEFAULT/SECRITY/
CONFIG/ENABLE is set to ON.
The password can contain a maximum of 16 
characters.
NoteEmpty passwords are not allowed.
FORMATERASE 
FLASHSettingsYES, NO
Select whether or not to initialize the flash RAM.
If YES is selected, the flash RAM is initialized.
RESTORE 
/SAVERESTORE 
FA C TO RYSettingsYES, NO
Select whether or not all menu items are reset to their 
initial settings.
If YES is selected, all menu items are reset to their initial 
settings.
SAVE 
CUSTOMSettingsYES, NO
Select whether or not all changed menu settings are 
saved.
If YES is selected, all changes are saved.
RESTORE 
CUSTOMSettingsYES, NO
Select whether or not menu items are reverted to the 
previously saved settings.
If YES is selected, the menu items revert to the previously 
saved settings.
System Default Menu
NoteAll factory default values are shown in bold.
Downloaded From ManualsPrinter.com Manuals